LED WORLD QL-F2216C150SA-X-24-M No Spot Lighting LED Flex Strip Instruction Manual

NO SPOT LIGHTING LED FLEX STRIP

Model: QL-F2216C150SA-X-24-M (X = COLOR W:Deep Warm White / P:Pure White)

ledworldlighting.com | ledworld.ca
1-800-387-4081

IMPORTANT INSTRUCTIONS

use only with Class 2 Type power units

Never Nail or use Staples

Only power with 24VDC Class 2 Power Source

Never apply weights or walk on strips

Apply to surface at room temperature. Keep away from flammable materials. Surface temperature MAX 40°C (104°F). Don’t install under, above or near heat sources (i.e. stoves, fireplaces)

SAFETY & WARNINGS

Please read instructions before using product and SAVE THESE INSTRUCTIONS. Before using this product make sure you have right color, product (item number) and voltage (printed on product). Check for possibility of damage during shipping. If damaged, or wrong product, do not use. Disconnect power before installing or using.

Use only with Class 2 Type power supply. Using with any other type of power supply will void the limited warranty.

Use only with LED World’s Class 2 Type power supply.
Disconnect power before installing or servicing (at breaker point).
This product is intended to be installed and serviced by a qualified licensed electrician. Install in accordance with the National Electric Code, and local regulations. Only power with a (listed) constant voltage Class 2 power supply (24V DC).
Never plug into 120V AC. The product requires a optional class 2 Transformer.

• Do not power when rolled. Lighting must be installed in a straight line on a flat surface. Do not curl or twist and roll out completely straight before applying power.
• Only install on smooth flat surfaces free of burrows that are fire retardant.
• Rigidly support wires with wire clamps.
• During installation, do not damage the printed circuit. Exposed wires can cause short circuit damaging product and creating a serious hazard. Do not mount in a manner or support LED Strip light in a manner that can damage the outer jacket or cord insulation. Do not install this lighting system where the exposed bare conductors can be shorted or contact any conductive materials. Carefully check that there is no wire cross-over or possibility in the future in area of installation.
• To reduce the risk of fire and overheating, make sure all connections are tight.
• Product is sold in the maximum length. Do not exceed or extend the length of the roll.
• Only qualified electrician or engineer can perform installation familiar with low voltage wiring techniques. Correct polarity is imperative (+/- is marked on printed circuit). Parallel connection only.
• DO NOT install on flammable material or possibility of in the future. Do not install any luminaire closer than 6 inches (15.25 cm) from any curtain, or similar combustible materials.
• The light and all its components cannot be mechanically pressed. Never apply to surface above 40°C (104°F).
• Voltage must not exceed 24VDC and must be regulated. Check that it is the correct voltage before applying power.
• This is not a toy. Keep out of children’s reach.
• Keep Flex strip spaced ¾” apart if placing next to each other.
• LED Flex Strip is flexible on horizontal axis.
• Not for use in mission critical, aircraft, emergency signs or lifesaving equipment.
• Static electricity can damage LED(s). Handle with care.
• Inspect installation after one hour and thereafter regularly.
• For stationary use only and not subjected to possible pressure or movement (or in the future).
• Not for in-wall use.
• Max. Soldering temperature cannot exceed 250°C (482°F) for a max of 4 seconds. Use 22~20 AWG wire to connect.
• Use correct wiring as required by local electrical code. Use a 20 gauge wire to attach to strip by solder (2464 type of wire). Connection to power source may use Wago™ 221-413 in hardwire applications.
• Cable lighting systems not be installed in bathrooms.
• Conductors of extra-low-voltage circuits be rigidly supported.
• Conductors not be installed in contact with combustible materials and not run through walls, ceilings, floors or partitions, and; Uninsulated conductors not be installed less than 2.2 m (86″) from the floor.
• Do not stare directly into the LED Light. Install LED lighting out of direct sight.

THREE YEAR LIMITED LIGHTING WARRANTY

LED WORLD INC. warranties this product for three year (some exceptions may apply) from the date of shipping unless otherwise noted in writing. This warranty is expressly in lieu of all other warranties expressed or implied. Under this Limited Warranty, the obligation of the company is limited to replacing on a prorated basis, at its option, any component found to be defective. This Limited Warranty does not apply to damage caused by buyer or alteration to the product or incorrect power supply. Factory warrantees are covered by the original manufacturer and claims must be submitted to them. This product must be used with LED World’s class 2 power supply. Failure to do so will void limited warranty.

LED World Inc. And its providers will never be liable to you or any other person for any indirect, incidental, consequential, special, punitive or exemplary loss or damage arising from, connected with, the purchase of products, including but not limited to loss of data, business, markets, cost of labour, savings, income, profits, use, production, reputation or goodwill, anticipated or otherwise, or economic loss, under any theory of liability (whether in contract, tort, strict liability or any other theory or law or equity), regardless of any negligence or other fault or wrongdoing (including without limitation gross negligence and fundamental breach) by led world inc or any person for whom led world inc is responsible, and even if led world inc has been advised of the possibility of such loss or damage being incurred.

If a product is defective, we will replace the product with similar or identical product or at our option a credit towards a future purchase. To make a claim under this warranty, obtain a return authorization number.

APPLICATIONS

• Back Lighting
• Cove Lighting
• Task Lighting
• Display Lighting
• Lighting Store
• Under Cabinet Lighting
• Accent Lighting
• Sign Lighting

FLEX STRIP CONNECTION

Wire connection using WAGO block connectors

LED Flex Strip

Connect No Spotting LED Strip with Power Connector
Note: Check the polarity. Red Wire(+), Black Wire(-)

INSTALLATION PLANNING

LED Flexstrip is a versatile lighting product that can provide a superior lighting solution in a variety of applications.
Recommend design steps before starting the installation process:
General questions based on lighting requirements:

• Where will your power supply be located
• How will you switch your LED lighting ON and OFF?
• What is the best layout configuration for your installation with wiring consideration?
• How will you run your wiring to your LED strip lighting?

WATTAGE CALCULATION

The LED Flex Strips have a label on each roll that indicates the voltage and wattage. You must have the correct Class 2 Power Supply (Transformer) for LED Strip model. To calculate the wattage, measure the total length of LED Strip in your run multiplied by the wattage of the LED Strip. Remember that a power source should only operate at a maximum 80% of it’s rated capacity.

For example : 10 feet of QL-F2216C150SA-X-24-M x 3.7W = 37 Watts

Never Extend the Length of rolls. Rolls are sold in there max length.

WIRING FOR VOLTAGE DROP

Voltage drop is normal loss of voltage that occurs as power flows along a wire connection in a low voltage systems, and increases as the length of a wire connection is increased. Wire length and thickness as well as total light wattage influence the amount of voltage drop.

Recommended maximum wire lengths – 24VDC

Wire Guage (AWG)| 20W| 30W| 50W| 60W| 90W| 100W
20 AWG| 13 FEET| 9 FEET| 5 FEET| 4 FEET| 3 FEET| 3 FEET
18 AWG| 21 FEET| 14 FEET| 8 FEET| 7 FEET| 5 FEET| 4 FEET
16 AWG| 34 FEET| 22 FEET| 13 FEET| 11 FEET| 7 FEET| 7 FEET

Download Magnitude app for voltage drop calculations:

Android App                        IOS App

LAYOUT OPTIONS

Note: Always check the Wattage of your LED Strip or Fixture.
Power Supply Wattage x 0.8 = Available Wattage

Layout 1

Layout 2

Layout 3

POWERING OPTION

Regulated Class 2 Power Supply

Figure shows LED Flexstrip connected to a Regulated Class 2 Power Supply

CUTTING AND CONNECTING

STEP 1: Turn Off power at the breaker.
STEP 2: Cut the LED Strip about 2 inch longer than required length.

STEP 3: Peel the extra length Silicone cover and look for cut-marks on the strip inside.

STEP 4: Make sure to cut the Strip at cut-mark only. Carefully check. STEP 5: Solder the 2464 low voltage wire to contact points if extending the length and use the provided end-cap with the holes. Check the polarity. For End of run use end-cap without the holes. Use with RTV type 108 silicone glue to seal with end cap.

IMPORTANT NOTE
Polarity marks must match ((+) to(+) and (-) to (-)) otherwise strip will not work

Seal with RTV type 108 silicone glue rated for use with electric wiring

TROUBLESHOOTING

Tape light strip does not light

• Make sure your power supply is turned on and has the correct voltage.
• Confirm you have the correct polarity (+ to + and – and -) throughout the run of LED Lighting.
• Have a electrician check all connections and any switch or dimmer connections from the power supply to the LED Light Strips.
• Consider testing with a multimeter to ensure light strip is receiving 24V power.

LED Flex Strip lights blink on, then go off

• The power supply is not adequate for the length of LED Light Strips you are powering. Install a adequate Class 2 power supply.

LEDs farthest from the power supply are noticeably dimmer

• This is the result of voltage drop. Decrease the length of the 24V power feed or use thicker power feed wires between the 24V power supply and the lighting strips.

IMPORTANT !

It is recommended to mount No Spotting LED Strip into 13 mm U channel PVC profile or use the included clip to install on surfaces.

IMPORTANT !

NOTE: Our LED Strip has female end connector at the one end. Cut end connector if soldering is required . Do not connect to another LED Strip. The LED Strip is sold in its maximum length to connect to a Class 2 power supply.

MAXIMUM FLEXSTRIP LENGTH SUPPORTED BY LED WORLD’s CLASS 2 POWER SUPPLY

LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 4.2 – 10/15/21

Copyright © 2021 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).

References

• LED World Canada - A Commercial LED lighting supplier
• LED World Lighting - A Commercial LED lighting supplier

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>