LED WORLD FC84M50-5M-24V-RGBW 24VDC LED Neo-Flex RGBW Strip Light Instruction Manual
- June 4, 2024
- LED WORLD
Table of Contents
LED WORLD FC84M50-5M-24V-RGBW 24VDC LED Neo-Flex RGBW Strip Light
IMPORTANT INSTRUCTIONS
Please read the instructions before using the product and SAVE THESE INSTRUCTIONS. Before using this product make sure you have the right color, product (item number) and voltage (printed on the product). Check for the possibility of damage during shipping. If damaged, or wrong product, do not use. Disconnect power before installing or using.
Use only with Class 2 Type power supply. Using with any other type of power supply will void the limited warranty.
- Use only with LED World’s Class 2 Type power supply.
- For wet location installations,seal all possible water entry points and covers using silicone Disconnect power before installing or servicing (at breaker point).
- This product is intended to be installed and serviced by a qualified licensed electrician. Install in accordance with the National Electric Code, and local regulations. Only power with a (listed) constant voltage Class 2 power supply (24V DC).
- Never plug into 120V AC. The product requires an optional class 2 Transformer.
- Ensure the overall length of the neon flex does not exceed the maximum run length as 15m one-end powered;30m two ends powered.
THREE-YEAR LIMITED LIGHTING WARRANTY
LED WORLD INC. warranties this product for five year (some exceptions may
apply) from the date of shipping unless otherwise noted in writing. This
warranty is expressly in lieu of all other warranties expressed or implied.
Under this Limited Warranty, the obligation of the company is limited to
replacing on a prorated basis, at its option, any component found to be
defective. This Limited Warranty does not apply to damage caused by buyer or
alteration to the product or incorrect power supply. Factory warrantees are
covered by the original manufacturer and claims must be submitted to them.
This product must be used with LED World’s class 2 power supply. Failure to do
so will void limited warranty. LED World Inc. And its providers will never be
liable to you or any other person for any indirect, incidental, consequential,
special, punitive or exemplary loss or damage arising from, connected with,
the purchase of products, including but not limited to loss of data, business,
markets, cost of labour, savings, income, profits, use, production, reputation
or goodwill, anticipated or otherwise, or economic loss, under any theory of
liability (whether in contract, tort, strict liability or any other theory or
law or equity), regardless of any negligence or other fault or wrongdoing
(including without limitation gross negligence and fundamental breach) by led
world inc or any person for whom led world inc is responsible, and even if led
world inc has been advised of the possibility of such loss or damage being
incurred. If a product is defective, we will replace the product with similar
or identical product or at our option a credit towards a future purchase. To
make a claim under this warranty, obtain a return authorization number.
TOOLS REQUIRED
INSTALLATION STEPS
- Solder the wire
- Use RTV 108 type silicon glue to connect end
- Complete connection
MOUNT NEO-FLEX STRIP INTO ALUMINUM CHANNEL/MOUNTING CLIP
- The mounting clip comes with self-lock bracket
- The aluminum channel comes with a self-lock bracket
- Place the self-locking bracket into the strip
- Push strip into Mounting clip/Aluminium channel
TROUBLESHOOTING
The tape light strip does not light
- Make sure your power supply is turned on and has the correct voltage.
- Have an electrician check all connections from the power supply to the LED Light Strips.
- Consider testing with a multimeter to ensure light strip is receiving 24V power.
LED Flex Strip lights blink on, then go off
- The power supply is not adequate for the length of LED Light Strips you are powering. Install an adequate Class 2 power supply.
LEDs farthest from the power supply are noticeably dimmer
- This is the result of a voltage drop. Decrease the length of the 24V power feed or use thicker power feed wires between the 24V power supply and the lighting strips.
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.1 – 09/20/21 Copyright © 2021 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specifications are subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>