welldana 34-131030 Flat LED lamp Instruction Manual

: June 3, 2024
: welldana

Table of Contents

well dana 34-131030 Flat LED lamp
Dimensione
Contents
Required tools for assembly
installation instructions
SAFETY WARNINGS
WARRANTY
ENVIRONMENTAL INFORMATION
Technical features
features
Documents / Resources

well dana 34-131030 Flat LED lamp

Dimensione

welldana-34-131030-Flat-LED-lamp-FIG-1

Required tools for assembly

welldana-34-131030-Flat-LED-lamp-
FIG-3

Alternative: 3 parts installation kit for freestanding pools

installation instructions

welldana-34-131030-Flat-LED-lamp-
FIG-4

IMPORTANT: This instruction manual contains highly important information about safety measures to be taken when installing and commissioning the device. It is therefore important for you to read these instructions before assembling and operating the product. Please keep this manual for later use. Lack of compliance with the instructions stated in this manual during the installation, operating, and maintenance phases shall relieve the manufacturer or distributor of any liability in the face of damages caused to people, to the product, or to the installation of the site, and will result in you losing the warranty.

GENERAL INFORMATION
This LED light was designed for immersed use in swimming water. It is a class III lighting system with Safety Extra Low Voltage of ∿12V(AC) or ⎓20V(DC). The light source cannot be replaced. If it stops working, the engine light will need replacing. It has an IP68 protection level and must be installed at a maximum immersed depth of 1 meter. This light also complies with international light safety standards, in particular standard IEC 60598-2-18 pertaining to swimming pool lights. It must be connected to a ﬂexible power lead with a minimum size of 2x1mm².
INSTALLATION
Correct installation requires for the light’s power circuit to be protected by a residual current device, with a maximum intensity of 30 mA. This light can only be connected to a double-insulated transformer or a double-insulated compatible stabilized safety power source. Any other type of voltage transformer is prohibited. We recommend for the transformer power be higher than the total power of all lights connected to the device. The manufacturer or distributor can in no way be held responsible for the assembly, installation, or operation of the product if it was manipulated or if non- provided electrical components were added.
ASSEMBLY AND REPLACEMENT
Please refer to the instruction sheet provided in this manual.
MAINTENANCE
This LED light does not require any form of maintenance. When the LED on the remote control no longer lights up, it’s very (model CR2032/3V/120mAh) needs to be replaced. If the light malfunctions, please contact either our customer service department or your retailer.
USAGE
This LED light should be used like any traditional incandescent lamp for swimming pools. Commands are given through the main ON/OFF switch on the pool’s electrical panel. You also have the option of connecting a remote control module of the same brand. The system oﬀers a 16-program cycle (11 set colors and 5 automatic color splashes). It requires manual control, once the power has been cut.

<3 s: switch to the following program
15s: switch back on to the program selected prior to the power cut
OFF > the 20s + ON 3-5s + OFF 3-5s + ON: light synchronisation (multiple installs)
Using the remote control requires you to be at a maximum distance of 10 meters from the light. The presence of metal, concrete or deep immersion can restrain the use of the remote control to a much shorter distance (1 to 2 meters). When ﬁrst using the remote control, you will need to conﬁgure it with its receiver – already integrated in the light system. (Please refer to the instructions in this manual)
On/Oﬀ (O): Switched on/Standby Colors (C): Access to 11 set colours Programs (P): access to 5 colour splashes Synchro (S): light synchronisation (multiple installations)

SAFETY WARNINGS

Before working on the light, it must be unplugged from the electrical network
All electrical connecons must be done outside the water
Never work on the device with wet feet
All prevenon standards currently in force must be complied with
IEC 364-7-702 standards in parcular must be complied with:

ELECTRICAL INSTALLATIONS INSIDE BUILDINGS. SPECIAL POOL INSTALLATIONS

Those in charge of assembly must be suitably qualiﬁed for this type of work
Switching the device oﬀ with the remote control will simply put it on standby
If the device stays oﬀ for more than 24h, we recommend using the switch located just before the transformer.

WARRANTY

This LED light is guaranteed against any material and/or manufacturing defects (electronic components) for 2 years starng from the date of delivery. (Substanang documents must be preserved) This light is not guaranteed against breakage caused by an external impact, a short circuit or excessive screwing, nor against power surges caused by the main power network. (In this case, the home insurance policy will kick in). This warranty is valid under the strict condion that the assembly and maintenance instrucons are complied with. Within the framework of this warranty, the manufacturer or distributor’s only obligaon will be to have their aer-sales service replace or repair the product or component recognised as defecve for free (the choice is theirs to make). Any other costs are to be covered by the purchaser. To beneﬁt from this warranty, products must ﬁrst be sent in to the manufacturer or distributor’s aer-sales service; their consent is mandatory if the product is to be replaced or repaired. The warranty shall not apply in the case of a visible defect. Defects and deterioraons caused by normal wear, malfuncons resulng from non- compliant assembly and/or usage, and product modiﬁcaons made without the manufacturer’s prior wrien consent are also excluded from the warranty.

ENVIRONMENTAL INFORMATION

In accordance with European Direcve 2002/96/EC, pertaining to waste electrical and electronic equipment (WEEE), the consumer must return any used products to suitable collecon points.