welldana 34-131050 LED Mini Light Instruction Manual
- June 3, 2024
- welldana
Table of Contents
welldana 34-131050 LED Mini Light
WHAT’S INCLUDE
Necessary
tools for assembly:
Options:
IMPORTANT: this instruction manual contains highly important information about safety measures to be taken when installing and commissioning the device. It is therefore important for you to read these instructions before assembling and operating the product. Please keep this manual for later use. Lack of compliance with the instructions stated in this manual during the installation, operating and maintenance phases shall relieve the manutacturer or distributor of any liability in the face of damages caused to people, to the product or to the installation Site, and will result in you losing the warranty.
DIMENSION
GENERAL INFORMATION
This LED light was designed for immersed use in swimming water. It is a class ll ighting system with Safety Extra Low Voltage of w 12V(AC) or -20V(DC). The light source cannot be replaced. If it stops working, the entire light will need replacing. t has an IP68 protection level and must be installed at a maximum immersed depth of 1 metre. This light also complies with international light safety standards in particular standard IEC 60598-2-18 pertaining to swimming pool lights. It must be connected to a flexible power lead with a minimum size of 2x1mm2.
INSTALLATION
Correct installation requires for the light’s power circuit to be protected by a residual current device, with a maximum intensity of 30 mA. This light can only be connected to a double-insulated transformer or a double-insulated compatible stabilized safety power source. Any other type of voltage transformer is prohibited. We recommend for the transformation power to be higher than the total power of all lights connected to the device. The manufacturer or distributor can in no way be held responsible for the assembly, installation or operation of the product if it was manipulated or if non-provided electrical components were added.
ASSEMBLY AND REPLACEMENT
Please refer to the instruction sheet provided in this manual.
MAINTENANCE
This LED light does not require any form of maintenance. If the light
malfunctions, please contact either our customer service department, or of
your retailer.
USAGE
This LED light should be used like any traditional incandescent lamp for swimming pools. Commands are given through the main ON/OFF switch on the pool’s electrical panel. You also have the option of connecting a remote control module of the same brand. The system offers a 16-programme cycle (11 set colours and 5 automatic colour splashes). Cutting the power supply allows for manual control.
- < 3 S: Switch to the following programme
- > 15s: switch back on to the programme selected prior to the power cut
- OFF >20s + ON 3-5s + OFF 3-5s + ON: light synchronisation (multiple installations)
SAFETY WARNINGS
- Before working on the light, it must be unplugged from the electrical network
- All electrical connections must be done outside the water
- Never work on the device with wet feet
- All prevention standards currently in force must be complied with
- IEC 364-7-702 standards in particular must be complied with: ELECTRICAL INSTALLATIONS INSIDE BUILDINGS. SPECIAL POOL INSTALLATIONS
- Those in charge of assembly must be suitably qualified for this type of work
- Switching the device off with the remote control will simply put it on standby
- If the device stays off for more than 24h, we recommend using the switch located just before the transformer.
WARRANTY
This LED light is guaranteed against any material and/or manufacturing defects (electronic components) for 2 years starting from the date of delivery (Substantiating documents must be preserved) This light is not guaranteed against breakage caused by an external impact, a short circuit or excessive screwing, nor against power surges caused by the main power network. (In this case, the home insurance policy will kick in). This warranty is valid under the strict condition that the assembly and maintenance instructions are complied with. Within the framework of this warranty, the manufacturer or distributor’s only obligation will be to have their after-sales service replace or repair the product or component recognized as defective for free (the choice is theirs to make). Any other costs are to be covered by the purchaser. To benefit from this warranty, products must first be sent in to the manufacturer or distributor’s after-sales service; their consent is mandatory if the product is to be replaced or repaired. The warranty shall not apply in the case of a visible defect. Defects and deteriorations caused by normal wear, malfunctions resulting from non-compliant assembly and/or usage, and product modifications made without the manufacturer’s prior written consent are also excluded from the warranty.
ENVIRONMENTAL INFORMATION
In accordance with European Directive 2002/96/EC, pertaining to waste electrical and electronic equipment (WEEE), the consumer must return any used products to suitable collection points.
Technical features
- SHOULD ONLY BE USED WITH A TRANSFORMER OR SAFETY POWER FEED
- USE ONLY IN OUTDOOR POOL
- «SPECIAL USE LAMP, COLOR CHANGING MODE NOT CONCERNED BY 1194/2012 PERFORMANCE»
FEATURE
Made in China and imported by
Welldana A/S – info@welldana.com
www.welldana.dk
Welldana A/S
Randersvej 6 DK-6700 Esbjerg
Phone +45 75 27 23 33
Fax +45 75 27 21 11
E-mail: info@welldana.com
www.welldana.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>