welldana 500743 Radio Remote Switches Instruction Manual
- June 3, 2024
- welldana
Table of Contents
welldana 500743 Radio Remote Switches
**RADIO REMOTE SWITCHES, 500743 & 500750
**INSTALLATION & MAINTENANCE
| 1 | Input ~12V |
|---|---|
| 2 | Output channel 1 |
| 3 | Output channel 2 |
| 4 | Output channel 3 |
| 5 | Output channel 4 |
| 6 | Fuse 20A |
| 7 | Pairing button |
| 8 | Pairing red LED |
IMPORTANT : This instruction manual includes essential information on the safety measures to be implemented for installation and start-up. It is important to read these instructions before beginning installation and start- up. Keep this manual for future reference. Failure to comply with the instructions given by the manufacturer in this manual regarding installation, operational start up and maintenance of the product exonerates the manufacturer or the distributor from any liability for damages affecting persons , the concerned product or the other installations, and shall void the guarantee .
VERIFY THE CONTENT OF THE PACKING
☑ Radio remote switch
☑ Antenna
☑ Radio remote controller with battery
☑ Installation and maintenance manuel.
GENERAL CHARACTERISTICS
This radio remote switch has been designed for inside or outside use. It is a
radio equipment accessory, class III electric apparatus, with a very low
safety voltage ~12V. It is recommended to be used ONLY with the lighting
systems of the SeaMAID range, working under the same voltage. This radio
remote switch complies with IP65 degree of protection.
This radio remote switch also complies with international safety standards for
electric devises, especially the IEC 61059 – 1 : 2002 +A2
INSTALLATION
For a correct installation, the power socket which feeds the installation lamp
will have to possess a device of protection by residual current with a maximal
intensity of 30mA. This radio remote switch will be only connected to a ~12V
security transformer with double winding. The maximum power of the one channel
switch is 120W and the maximum power of the four channels switch is 240W (120W
per channel max).
The radio remote switch must be installed vertically against a smooth wall,
antenna on the top of the box. To increase the radio signal, it is recommended
to install the radio remote switch outside with a direct view to the emitter.
The manufacturer is not responsible in any circumstances for assembly,
installation or start-up of any electric components which have been inserted
or handled at locations other than its own premises.
ASSEMBLY
Before any installation, it is important to verify that the total power of the connected projectors is lower than the maxi power admitted by channel and by the radio remote switch.
- Before installing this switch, ensures that the power supply is turn OFF.
- Undo and remove the cover of the box
- Fix the box vertically against the selected smooth wall with antenna base on the top
- Screw the antenna on its base
- Connect the 12VAC power cable from the transformer to the INPUT connector (1)
- Connect the low voltage projector(s) on the corresponding channel
- Restore the current
- Proceed to the radio remote controller pairing
- Replace the cover and re-screw it
- Test all functions by pressing buttons O and X of each channel
MAINTENANCE
This radio remote switch does not require any type of maintenance work. When
the red LED of the remote controller does not light anymore, replace the 12V
MN23 type alkaline battery.
In case of improperly working, please contact our customer service or the
customer service of our dealer.
OPERATION
The system works like an ON/OFF switch, driven by a radio remote controller. First use needs to proceed to a pairing process between the radio remote controller and the radio receiver installed in the box.
Pairing process :
- Install the battery in the remote controller
- Press the black button on the electronic board of the switch (7)
- The red LED lights fixedly (8)
- Press any button of the remote controller
- The red LED flash and stops (8)
- The system is ready for use
Remote control function:
On/Off: press O button.
Program change: press X button.
Channel synchronizing: (ref: 500750)
To synchronize the 4 channels of the switch, press 20 seconds X3 and X4
buttons together till getting a flashing confirmation of the connected lamps.
To unsynchronized the channels, press 20 seconds O3 and O4 buttons together
till getting a flashing confirmation of the connected lamps.
Metallic parts and electrical devices close to the radio switch can disturb
the radio signal. In this case, it is recommended to install the switch in a
better place or add a wired external antenna in option.
SAFETY WARNINGS
Before any operation ensures that the main power supply is turned OFF
Do not handle with wet feet
Comply with the current standards regarding accident prevention
In this regard, the IEC 364-7-702 standards must be observed : WIRING IN BUILDINGS, SPECIAL WIRING, SWIMMING POOL S.
The persons in charge of the assembly of this product must have the qualification required for this kind of work.
GUARANTEET
his radio switch is guaranteed 24 months against any material and/or
manufacture defect (electronic components) from the date of delivery. (Keep
the purchase invoice/receipt) The switch is not guaranteed against problems
coming from external shock, electric short-circuit or excessive screwing. The
product is not guaranteed against electrical excessive voltage coming from the
external power supply. (In this case, refer to the house insurance coverage)
This guarantee is conditioned with the strict respect of these instructions of
assembly and maintenance. Under this guarantee, the only obligation falling on
the manufacturer or distributor will be the free replacement or repair of the
product or the element found defective by their after sale services. All the
other expenses will be the responsibility of the purchaser. For any
replacement or repair, the product must be subjected to an inspection to the
after-sales service of the manufacturer or distributor. The guarantee does not
play in the event of apparent vice.
The defects and deteriorations caused by the fair wear and tear, the defects
resulting from a wrong assembly and/or employment, and the modifications of
the product carried out without the written and preliminary assent of the
manufacturer are all also excluded.
ENVIRONMENTAL INFORMATION
In accordance with the European Directive 2002/96/CE, concerning the electric and electronic component scrap (EEED), the consumer must turn over the used product to the collect points envisaged to this end.
EC DECLARATION OF CO’NFORM TY
The products listed above are in compliance with :
Electromagnetic Compatibility Directive
2014/30/UE.
Low Voltage Directive 2014/35/UE.
Radio Directive RED 2014/53/UE.
Signature:| SAS ALPHADIF
BP 355 – 1522 Avenue de Draguignan
83077 TOULON ·Cedex 9 – France
| Toulon, le 01 /08/2018
La Direction – PhiliJ2 e POMA
---|---|---
TECHNICAL DATA
Channel number
Input/Output current
Power
Protection
Standby consumption
Working temperature
Working humidity
Connectors
IP index
Radio frequancy
Remote controller provided
TO BE USED ONLY WITH A SECURITY TRANSFORMER
Documents / Resources
|
welldana 500743 Radio Remote
Switches
[pdf] Instruction Manual
500743, 500750, 500743 Radio Remote Switches, 500743, Radio Remote Switches,
Remote Switches, Switches
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>