ilight Plexineon Vertical Catenary Dynamic Color Instruction Manual
- June 3, 2024
- ILIGHT
Table of Contents
Plexineon Vertical Catenary Dynamic Color
Instruction Manual
REV0.1 10252022
Plexineon Vertical Catenary Dynamic Color
Installation Instructions – Plexineon Vertical Catenary Dynamic Color
Models: Plexineon Vertical Rings Catenary Mount Dynamic Color
Please read all instructions prior to installation and keep for future
reference!
- PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.
- USE ONLY WITH CLASS 2 POWER UNIT
- 24 VOLTS DC
- SUITABLE FOR WET LOCATIONS
- CATENARY MOUNT ONLY
NOTE: Prior to installation all 24VDC wires must be present within 72” of
the installation. Refer to the power supply installation instruction for
additional information.
NOTE: More than one person is recommended for this installation.
NOTE: This step is only for multi-piece frames. If you have single piece
frame, skip to step 2.1.
1.1 For multi-piece frames, connect the frame members together with
mounting frame joiner.
2.1 Install plexineon fixture to mounting
clips on mounting frame(s).
Install Fixtures into Mounting Clips
A.1 Make an U shape with mounting clip installation tool, insert two edges
into mounting clip. Place plexineon fixture insde the shape. Then push the
fixture into clip.
A.2 Remove the tool. Make sure mounting clip is clipped right on the grip.
3.1 Remove screw, u-bolt, saddle, and locknut from collar.
3.2 Connect collar with mounting frame by screws. Use locknut to secure
collar. 
NOTE: Catenary cables are provided by others. Max Ø1/4”.
4.1 Place the catenary cable between the saddle and u-bolt. Use locknuts to
clamp the catenary cable between the saddle and u-bolt. 
5.1 Loosen the top locknut on back of the collar to adjust the angle
of plexineon fixture.
RGB&RGBW WIRING DIAGRAM
WIRING DIAGRAM
SR-DMX-SPI
Smart Pixel LineLED Decoder
NOTE: Please make sure that power is turned off before wiring. Also,
ensure that the correct power supply (voltage and wattage) is used to power
the LED strips connected to the decoder. Follow illustrated wiring diagram.
Use screwdriver to open and close connection slots.
NOTE: When connecting two or more LED strip lights or light fixtures,
always make sure the signal direction arrows are pointing to same direction
The signal direction arrow should appear on label of each section of LED
fixture.
OPERATING GUIDE
SR-DMX-SPI
Smart Pixel LineLED Decoder
There are three buttons on the decoder.
After operation, if no
action was taken within 30s, the button lock, and backlight of the screen will
turn off.
- Long press M button for 5s to unlock the buttons, and the backlight will turn on.
- Long press M button for 5s to switch between test mode and decode mode after unlocked.
During test mode, the first line of LCD will show: TEST MODE. Use test mode to
verify RGBW Pixel functionality.
Duirng decoder mode, the first line of LCD shows: DECODER MODE. Use decoder
mode when connecting to a Controller and for final installation and
customization.
The second line of the LCD Display shows the current setting and value. Note:
1 Pixel = 1 Cut Increment
NOTE: When connected to a controller, DMX512 Signal Decoder will stay in
“Decoder Mode”.
MODE TABLE.
| SETTING | LCD DISPLAY | VALUE RANGE | DESCRIPTION |
|---|---|---|---|
| Built-in Programs | TEST MODE MODE NO.: | 1-26 | See Program Table below |
| Program Speed | TEST MODE RUN SPEED: | 0-7 | 0: fast, 7: slow |
| DMX Address | DECODER MODE DMX ADDRESS: | 1-512 | Address of the starting |
point/Pixel of a program
DMX Signal RGB| DEE)C01:11RalsOSE MX| RGB, BGR, etc.| N/A
Pixel Quantity| DECODER MODE PIXEL QTY:| 1-170(RGB), 1-128 (RGBW)| Number of
Pixels to follow a program
IC TYPE| DECODER MODE IC TYPE:| 2903, 8903, 2904, 8904| 2903: N/A, 2904: for
RGBW,
8903: N/A, 8904: N/A
Color| DECODER MODE COLOR:| MONO, DUAL,
RGB, RGBW| MONO: N/A,
DUAL: N/A,
RGB: N/A,
RGBW: for RGBW
Pixel Merging /Pixel Size| DECODER MODE
PIXEL MERGE:| 1-100| Number of Pixels to merge together
RGB Sequence| DECODER MODE LED RGB SEQ:| RGBW, BGRW, etc.| Sequence of RGBW,
24 possible combinations
Integral Control| DECODER MODE ALL CONTROL:| YES, NO| Yes: Merge all Pixels
No: Maintain individual Pixels or Merged Pixels
Reverse Control| DECODER MODE REV-CONTROL:| YES, NO| Reverse program order
Overall Brightness| DECODER MODE BRIGHTNESS:| 1-100| 1: dimmest setting 100:
brightest setting
NOTE :
When connected to a controller, DMX512 Signal Decoder will stay in “Decoder
Mode”.
NOTE:
The actual maximum control pixels of the controller are 1360 (2903) ,1024
(2904). Please set the pixel and pixel combination value according to the
actual situation, and DO NOT exceed the maximum.
NOTE: For Program Table
Change: no fading/dimming between color changes
Fade: fade/dim between color changes Chase: change pixel by pixel
Chase with Trail: change pixel by pixel with fading between
PROGRAM TABLE
| PROGRAM NO. | PROGRAM DESCRIPTION |
|---|---|
| 1 | Solid color: Red |
| 2 | Solid color: Green |
| 3 | Solid color: Blue |
| 4 | Solid color: Yellow |
| 5 | Solid color: Purple |
| 6 | Solid color: Cyan |
| 7 | Solid color: White |
| 8 | RGB change |
| 9 | Full color change |
| 10 | RGB fading |
| 11 | Full color fading |
| 12 | Red chase with trail |
| 13 | Green chase with trail |
| 14 | Blue chase with trail |
| 15 | White chase with trail |
| 16 | RGB chase with trail |
| 17 | Rainbow chase with trail |
| 18 | RGB chasing and fading |
| 19 | Red chasing green, chasing blue |
| 20 | Orange chasing purple, chasing cyan |
| 21 | Rainbow chase (7 colors) |
| 22 | Random twinkle: white over red |
| 23 | Random twinkle: white over green |
| 24 | Random twinkle: white over blue |
| 25 | White fading |
| 26 | Off |
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>