SEALEY ES350.V2 350kg Engine Stand Instruction Manual
- June 3, 2024
- SEALEY
Table of Contents
ENGINE STAND 350KG
MODEL NO: ES350.V2
ES350.V2 350kg Engine Stand
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE ND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
SAFETY
WARNING! Ensure all Health and Safety, local authority, and general
workshop practice regulations are strictly adhered to when using this
equipment.
DO NOT use unit if damaged.
Replace or repair damaged parts. Use recommended parts only. Unauthorised
parts may be dangerous and will invalidate the warranty.
Keep the stand clean for best and safest performance.
Locate the stand in a suitable work area. Keep area clean and tidy and free
from unrelated materials. Ensure there is adequate lighting.
Use on a firm, level surface capable of sustaining the stand and the load.
Maintain correct balance and footing. Ensure the floor is not slippery and
wear non-slip shoes.
Ensure all non-essential persons keep a safe distance whilst the stand is in
use.
Lock mounting plate in position with locking pin before fixing a load and
ensure the load is centred and securely mounted on the mounting plate.
When an engine is mounted, take the weight of the engine on the handle before
removing the locking pin.
Ensure the stand and load are stable.
To move a loaded stand, steady the load and push from behind the main post of
the stand so that the castor wheel is ahead of the load.
DO NOT pull the unit backwards, or push from the side, as this may cause the
stand to tip.
Ensure surface over which the stand is to travel is strong enough to take the
stand and load and that it is not cracked, uneven or obstructed.
DO NOT allow untrained persons to use the stand.
DO NOT exceed the rated capacity of 350kg.
▲ DANGER! DO NOT work under an engine mounted on the stand.
DO NOT use the stand for purposes other than those for which it is designed.
When not in use store stand in a safe, dry, childproof area.
INTRODUCTION
Accepts a wide variety of engines and transmissions. The heads swivel 360° for accessibility to all parts of the engine. Fully adjustable mounting arms. Swivel castors provide excellent manoeuvrability. Maximum Load Length: 700mm.
SPECIFICATION
Model No: …………………………………………………………. ES350
Capacity: ……………………………………………………………. 350kg
Nett Weight: ………………………………………………………. 16.9kg
Size (W x D x H): ………………………………890 x 790 x 920mm
Maximum Load Length: ………………………………………. 700mm
ASSEMBLY
4.1. Referring to fig.1, slide a wheel (20) onto each axle stub at either end
of the axle leg (3). Place an M16 axle washer (21) over each stub and retain
each wheel by pushing a R spring clip (22) through the hole in the end of each
axle stub.
4.2. Referring to fig.2, bolt the castor (15) to the mounting plate at the end
of the front leg (2) using four M8 bolts (16), four M8 flat washers (18), four
spring washers (19) and four M8 nuts (17).
4.3. Referring to fig.3, attach the four engine mounting arms (10) to the
mounting plate (8) using four M14 bolts (11), four M14 flat washers (13), four
spring washers (12) and four M14 nuts (14).
4.4. Assemble the main frame referring to fig,4. Slide the front leg (2) into
the square tube at the base of the main post (1) ensuring that the castor is
facing downwards and the hole at the other end of the leg is aligned with the
hole in the bottom of the square tube. Insert the 70mm M8 bolt (4) entirely
through the axle leg (3) then bring the leg up underneath the main post so
that the protruding bolt appears inside the square tube. Fix the three main
components together using the M10 washer (5), M10 spring washer (7) and the
M10 nut (6) and tighten firmly.
4.5. Take the engine mounting plate assembly and insert the tubular section
through the tube at the top of the main post. Rotate the assembly so that one
of the six holes in the inner tube aligns with the single hole in the top of
the post. Insert the locking pin (9).
4.6. Insert the handle through the holes in the rear end of the engine
mounting plate tube.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice. Please note that other versions of this product are available.
If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk
or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
| 01284 757500
---|---
| 01284 703534
| sales@sealey.co.uk
| www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
ES350.V2 Issue 3 (2,3) 08/08/22
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>