phrozen Sonic Mighty 8K 3D Printer User Guide

: June 3, 2024
: phrozen

phrozen Sonic Mighty 8K 3D Printer User Guide

01 Before You Start

Stable Printing Environment

Store your 3D printer in a dry and ventilated environment. Avoid exposure to direct sunlight. Make sure to place the printer on a Gat surface.

Protective Measures

While printing and using resin, please make sure to wear gloves, masks, protective goggles, and long-sleeved clothing.

Maintenance

Clean the Z-axis First, dry clean the Z-axis T-screw. Then apply a thin layer of general lubricant to it, so that it rotates smoothly. Clean the 3D Printer
Use 95% alcohol and tissue paper to carefully clean the printer, the resin vat, and the building plate.

The To olb ox

Operation

System Operation
Slicer Software Connectivity
Phrozen OS 5 inch Touch Panel CHITUBOX V2.0
USB | Ethernet | Wi-Fi

Printing Specifications __

Technology

Resin 3D Printer – LCD Type

Light Source XY Resolution Layer Thickness
Max Printing Speed
Power Requirement
Linear Projection LED Module 28 μm0.01-0.30 mm70 mm / hr 24 VDC;5A

Hardware Specifications

Printer Size Printing Volume Printer Weight
L33.7 x W33.7 x H51.6 cm L21.8 x W12.3 x H23.5 c

All specifications have been tested in a laboratory. Please note that certain specifications may be subject to change without prior notice

0 3 Prepare Your 3D Printer

Gu i ded Pr o ce s s fo r Ini tia l Us e _
_Follow the guides on the touch screen during initial use to complete the LCD test, Z-axis calibration, and test printing ( XP_finder.stl file ) in order to confirm the relevant settings
of t h e pr i nte r. If yo u m issed the guided pr oce s s, y o u ca n set i t up by following the steps in t he manual.

Ha r dw a re Test

I t is reco mm ende d t o pe rform th e ha r dw are te st w hen printing for the first time by following the steps below:

O per ate t he le ft co lum n and sw itch t o th e “Se tting s” p age _> c_li ck “ Sys t em “ _ > _S wip e do wn and cli c k “ Hardware

The test contents include:

Light cooling fan switch test.
LCD test: Please refer to the “LCD Test.”
Z-axis running test: Press and hold the key all the way to the bottom to confirm that the building plate moves normally.
Z-axis sensor detection: When the building plate reaches the bottom, the light display will turns green.
Printer firmware version.

LCD Test

Remove the resin vat and wear anti-UV goggles to avoid eye injury.
Test the “LIGHT UP, LCD GRID, and BLACKEND” modes one after another to make sure the LCD screen displays the same images as shown on the touch panel. The test will run for 30 seconds in each mode.
When the LCD screen fully displays the three modes. The LCD Test is completed.

Z-axis Calibration

Notice! The other Z-axis control could NOT be turned on, If the Z-axis calibration was not executed during initial use.
Use the following steps to calibrate your Z-axis: Click “Tools” > click “Z-axis Control” > click “Z-axis Calibration.”
Follow the instructions on the screen to execute Z-axis calibration:
• Remove the resin vat. Place an A4 paper on the LCD screen
. • Loosen the four screws on both sides of the building plate.
• Wait until the building plate touches the LCD screen.
• Then tighten all four screws.
• Click “DONE” to finish calibration. Wait until the building plate retracts to the TOP.

Z-Offset Setting After calibrating the Z-axis, you can use this function to modify your Z-offset position when needed. You may also use this function if you want to print flat on the building elate or if the resin flow is slow.

For initial use, please perform Z-axis calibration first.
Click “Move to Zaxis zero position.”
We recommend to use 0.1mm setting as an elevating unit to fine-tune the position.
After confirming the position, click “Reset Z-Offset” to complete the setting. IMPORTANT NOTICE: After resetting or rebooting the hardware, please reconfirm the Z-offset distance before printing.

Z-Offset Setting After calibrating the Z-axis, you can use this function to modify your Z-offset position when needed.
You may also use this function if you want to print flat on the building elate or if the resin flow is slow.

For initial use, please perform Z-axis calibration first.
Click “Move to Zaxis zero position.” 3 We recommend to use 0.1mm setting as an elevating unit to fine-tune the position.
After confirming the position, click “Reset Z-Offset” to complete the setting. IMPORTANT NOTICE: After resetting or rebooting the hardware, please reconfirm the Z-offset distance before printing.

05 File Import & Internet Connection

Sonic Mighty 8K can transfer files through USB drive and internet connection. The printer has 3.5GB of built-in memory, able to save transferred files.

Import Files Through USB

Use CHITUBOX to slice the printing file, save it as a CTB file onto the USB drive, and insert the USB drive into the printer.
Perform the following operations on the touch panel in the “Print” page: Click the “USB” > select file > “PRINT.”

Connecting The Printer to a Computer

Select the internet connection method Use the USB wireless network card included in the accessory box to connect to Wi-Fi, or insert the network cable and connect through Ethernet. 2 Connecting to the internet Enter the “Settings” page, click “Network,” and select “Wi-Fi” or “LAN Cable” on the side.
Confirm the printer IP Return to the “Settings” page > Click “Sharing Network” > Enable the setting. The IP address is at the bottom-most field.
Connecting the printer to a computer Have the computer connect to the same local area network as the printer, and enter the printer IP number into the empty folder location. *The username and password have to be entered manually for initial use.

06 Printing Test

Use Aqua-Gray 8K resin and the “PhrozenXP Finder” model CTB file to perform testing.
Install the building plate and resin vat. Confirm that both are clean with no foreign objects.
Shake the resin evenly and pour it into the resin tank. Do not exceed the “MAX” mark on the resin tank when pouring.
nsert the USB drive or select the “Phrozen_XP Finder_AQ8K.ctb” file in the printer and click “Print.”
Keep the plastic case closed during printing to prevent excessive UV light exposure. 6 Once printing is complete, remove the building plate from the printer.
Then tilt, place the building plate onto a table and use the metal scraper to carefully remove your print. 7 Use 95% alcohol or Phrozen Wash Resin Cleaner to rinse your printed model, Then cure your models with a post-curing chamber; after curing, your first print is complete.

After-sales service & warranty

Phrozen offers a one-year warranty for all parts, excluding consumable components such as the LCD screen and PFA(nFEP) film.
Sonic Mighty 8K LCD screen is covered under a 3-month warranty. Please note that this warranty does not cover any damages caused by human factors.
If you encounter any difficulties, please scan the QR code to contact us.

Congratulations!

You have just completed your first run. We hope you’ve had a great experience!
Please follow Phrozen’s social media accounts and subscribe to our YouTube channel to learn more about printing tips and share information with the community.