AURORA AU870MA Shredder User Manu User Guide

Shredder User Manual

AU870MA Model No.
1-800-327-8508

AU870MA Shredder User Manu

Please read these operating instructions before using the unit.

**WARNING:** SAFETY INSTRUCTIONS, READ BEFORE USING!

| Read instructions before use.
---|---
| Avoid touching the document feed opening with hands.
| Product is not intended for use by children (product is not a toy).
| Do not insert foreign objects into the paper entry slot.
| Do not spray or keep any aerosol products in or around the shredder.
| Keep loose clothing or jewelry away from the paper entry slot.
| Avoid getting hair near the paper entry slot.

• Always turn the shredder off and unplug the power cord from the AC outlet when not in use, before cleaning it, moving it, or emptying the waste basket.
• RISK OF FIRE – Serious injury, loss or damage may occur. Never use any petroleum based or flammable oils, spray can oil or lubricants, or any aerosol products in or around the machine as some oils can combust causing serious injury.
• NEVER dispose of flammable chemicals or materials that have come into contact with flammable chemicals (for example, nail polish, acetone and gasoline) in the shredder basket.
• Never shred large paper clips, window or insulated envelopes, continuous forms, newsprint, bound pages (in example: notepads, checkbooks, magazines, etc…), transparencies, laminated documents, cardboard, any items with adhesives, hard materials or plastic (except Credit Cards).
• A socket-outlet should be near the equipment and be easily accessible.
• Never let the wastebasket become full. This will lead to shredded material being pulled back up into the shredder and cause jams.
• Never place the shredder near water or any heat source.
• Do not use the shredder if the power cord is damaged in any way.
• Do not attempt to service this product yourself as doing so may expose you to sharp cutting blades and/or electricity and will void the manufacturer’s warranty.
• Never try to clean or clear the shredder blade.
• Never shred beyond the specified sheet capacity. This may result in extensive damage to the machine.

Paper Shredder
Operating Instructions
Installation
Operation
Maintenance
Troubleshooting
Service Center
Limited Warranty

* ONE FOLDED SHEET OF PAPER EQUATES TO 2 SHEETS OF PAPER
Heavier paper, humidity or other than rated voltage may reduce shredding capacity.

INSTALLATION

1. This model includes a built-in safety interlock mechanism, which requires the shredder to be correctly mounted on to the included wastebasket. (FIGURE 1) THE SHREDDER WILL NOT OPERATE UNLESS IT IS PROPERLY MOUNTED AS PICTURED.
2. A socket-outlet should be near the equipment and be easily accessible.
3. Connect the power cord to any standard 120 volt AC outlet.

Caution: Microcut shredders have very sharp exposed blades on the underside. Use care when mounting the shredder on the wastebasket.

OPERATION

1.Control Switch

• Using the switch located on the unit, select one of the following settings by sliding the switch either left or right. (FIGURE 2)

I AUTO: This setting allows the shredder to be automatically started by inserting paper into the feed slot. Always feed the paper in as straight as possible. When the paper has passed through, the shredder will automatically stop.
O OFF: This setting turns off all features of the shredder. For safety reasons, we recommend that you leave the shredder in the “Off” position whenever the shredder is unattended or not in use.
R REV (REVERSE): In the unlikely event of a paper jam, the reverse setting can be used to help clear the cutters of paper that did not pass through. Never attempt to clear a jam by using the reverse function until you have emptied the wastebasket.
LED Status Indicator:

Overheat: Red light – Shredder has shred continuously beyond the maximum shred time and needs to cool down before operation can restart. If this happens, switch the shredder off for 30 minutes or longer before resuming normal operation.
2. Paper / Credit Card Entry:

1. Make sure you do not exceed sheet count per pass (8 sheets max). Insert paper as straight as possible into feed slot and release.
2. Insert one credit card at a time into the middle of the feed slot.

NOTE:

• Always turn off and unplug the shredder when not in use.
• This shredder will shred staples and small paper clips. It is recommended that you remove paper clips whenever possible to extend the lifespan of your shredder.
• Only shred credit cards by feeding them vertically i nto the middle of the entry, releasing when shredding begins. Never feed more than one credit card at a time.
• Overfeeding the shredder: Shredding beyond the specified sheet capacity can result in extensivedamage to the shredder. Overfeeding will strain the machine and quickly wear and break the cutting blades and internal components.
• Overheating with extended use: In the event that the shredder has shred continuously beyond the maximum running time and overheating, the unit will automatically shut off. If this happens, switch the shredder Off for 30 minutes or longer before resuming normal operation.

MAINTENANCE

• Warning: Failure to properly maintain your shredder will void the warranty.
• Oil the shredder blades every month with basic vegetable, cooking oil or shredder oil. Follow oiling procedure below (FIGURE 3). It helps to keep the shredder blades operating well over many years of use.

Oiling procedure:

1. Turn off shredder.
2. Apply shredder oil across paper entry.
3. Turn shredder in reverse mode for 3~5 seconds.
   Note: lubricating oil is NOT included.

Caution:

• Do not spray or keep any aerosol products in or around shredder.
• DO NOT USE CANNED AIR ON SHREDDER.

CLEANING:

• ALWAYS UNPLUG THE SHREDDER BEFORE CLEANING!
• Only clean the shredder by carefully wiping the unit with a dry soft cloth or towel.
• Do not clean or immerse shredder in water. Having the unit wet may result in damage or malfunction to the electrical components. If the shredder happens to get wet, be sure to completely dry the unit immediately with a cloth or towel.
• Never use anything flammable to clean the shredder. This may result in serious injury or damage to the product.

TROUBLESHOOTING

If there is a problem with your shredder, check below for the symptoms and steps to resolve. If you continue to have problems, contact customer support at our Service Center 1-800-327-8508.
DO NOT ATTEMPT TO REPAIR BY OPENING THE SHREDDER HEAD. This will completely void the product warranty.
The shredder does not work at all.

1. Make sure the unit is plugged in and that the outlet is in good working order.

2. Overheating with extended use: In the event that the shredder has shred continuously
   beyond the maximum running time and overheated, the unit will automatically shut off. If this happens, switch the shredder Off for 30 minutes or longer before resuming
   normal operation.

3. If using a plastic bag to line the wastebasket, please remove it. This may cause the shredder not to operate properly.

4. The activation sensor of the shredder is located near the center of the feed slot. Be sure to feed directly into the center area to activate the machine (especially applies to smaller pieces of paper or credit cards).

The shredder runs in “Rev (Reverse)” mode but not in “Auto (On)” mode.
While in “Auto” mode, the motor will not start running until paper is inserted into the feed slot. Set the unit to “Auto” and insert paper to shred. The sensor that activates the shredder in Auto mode is located directly in the center of the slot. If the paper you are inserting is narrow, it may not be activating the optical sensor. It is also possible that the feed slot has become blocked with paper. Insert an index card or any rigid sheet of cardstock (old greeting card or folded file folder), directly in the center of the feed
slot, while applying force to help push the jammed paper through. This will usually clear any paper blockage.
How to clear a paper jam in the shredder.

1. Switch the shredder over into Reverse (REV) mode. While in Reverse, the shredder will back up and loosen the jammed paper. If required, you may need to tug and remove several sheets to effectively clear the machine. When jammed paper is loosened or removed, switch back to the Auto-On mode to continue shredding. Repeat steps if needed.
2. With stubborn situations where the reverse function does not help, you may loosen the jammed paper with shredder oil (cooking oil is acceptable, nothing aerosol).
   Starty drizzling oil into the feed slot where the paper is jammed. Let it soak for about 30 minutes to completely saturate. Return the shredder back to Auto- On mode. If required, an index card or a rigid sheet of cardstock (old greeting card or folded file folder) can be fed into the shredder to help push the jammed paper through.

CONTINUED NEXT PAGE

The shredder is constantly running while in “Auto (On)” mode.

1. It is possible that the activation sensor, which starts the shredder, has become blocked with paper. Insert an index card or any rigid sheet of cardstock (old greeting card or folded file folder), directly in the center of the feed slot, while applying force to help push the jammed paper through. This will usually clear any paper blocking the activation sensor and feed entry.
2. The activation sensor is being triggered by dust, debris, or oil. A cotton swab may be used to clean the sensor. DO NOT USE CANNED AIR. The activation sensor of the shredder is located around the center of the feed entry.

SERVICE CENTER

If you have any questions in regards to the operation of this shredder or in need of a spare part, please contact our service center at:
Telephone: 1-800-327-8508 (U.S.A. only) or 1-310-793-5650 (International)
Business hours: Monday to Friday 8:00 am – 5:00 pm PST (Pacific Standard Time)
Email: info@auroracorp.com
Or for more information, please visit our website at http://www.auroracorp.com

LIMITED PRODUCT WARRANTY

We warrant the cutting cylinders of the machine against defects of workmanship and material for a period of 5 years from the original purchase date to the original consumer, and all other parts of the machine against defects of workmanship and material for a period of 1 year from the original purchase date to the original consumer.
Should there be a defect or malfunction of this product, we will repair or replace the product free of charge. Customer is responsible for all shipping charges to return the defective product to us. A copy of the proof of purchase showing original purchase date is required. This warranty is void if the product has been subject to damage, unreasonable use, improper service, or other causes not arising from defects in original material or workmanship. This warranty is void if factory seal is broken or removed from the product. This warranty does not include adjustments, parts or repairs required by circumstances beyond the control of us.
There are no expressed warranties other than those stated herein.
Any expressed or implied warranties, including but not limited to merchantability and fitness for a particular purpose are limited to the above warranty period. We shall not be liable for any incidental or consequential cost, expenses or damages resulting from any failure defect or malfunction of this product.
Some states do not allow the exclusion of limitations of implied warranties or consequintial damages, therefore, the above limitations may not apply to you.
This warranty grants you specific legal rights, and you may also have other rights that vary from state to state.
Before returning any product, please call our Service Center for specific return instructions.
1-800-327-8508 USA ONLY
1-310-793-5650 INTERNATIONAL
info@auroracorp.com

1-800-327-8508
USA Only
• 1-310-793-5650
International
• Email: info@auroracorp.com 
• For more information, please visit us at: www.auroracorp.com
© 2020 Aurora Corp. of America
3500 Challenger Street, Torrance, CA 90503 USA
041420

References

• Aurora Corp. of America

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>