Einhell MM 52 I AS Petrol Multi Function Tool Instruction Manual
- July 26, 2024
- Einhell
Table of Contents
Einhell MM 52 I AS Petrol Multi Function Tool
Product Usage Instructions
Safety Guidelines
Before Use:
- Ensure the area is clear of any flammable materials before starting the tool.
- Check that all connections are secure and the tool is free of any debris or fuel residue.
- Always operate the tool with both hands on the handles for better control.
Operating Instructions:
- Start the engine according to the manufacturer’s instructions.
- Adjust the cutting height as needed for the task at hand.
- Use the tool in a sweeping motion for optimal results.
- Regularly check and refill fuel as necessary during use.
Maintenance:
- After each use, clean the tool thoroughly and store it in a dry place away from direct sunlight.
FAQ
- Q: How often should I sharpen the cutting blades?
- A: It is recommended to sharpen the cutting blades after every 25 hours of use for optimal performance.
- Q: Can this tool be used for trimming hedges?
- A: No, this tool is designed for cutting grass and light brush only. Do not attempt to use it for trimming hedges.
Danger! When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care. Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well. We cannot accept any liability for damage or accidents which arise due to a failure to follow these instructions and the safety instructions.
Safety regulations
Danger! Read all safety regulations and instructions. Any errors made in
following the safety regulations and instructions may result in an electric
shock, fire and/or serious injury. Keep all safety regulations and
instructions in a safe place for future use.
Safety devices When working with the equipment, the appropriate plastic guard
hood for cutting blade mode or cutting line mode must be fitted to prevent
objects being thrown out by the equipment. The integrated blade in the cutting
line guard hood automatically cuts the line to the optimum length.
Safety information
· Read the operating instructions carefully.
Familiarize yourself with the settings and with the proper use of the
equipment.
· Never allow other persons who are not familiar with the operating
instructions to use the equipment. Contact your local governmental agency for
information regarding minimum age requirements for the user.
· Never mow in the direct vicinity of persons especially children – or
animals. Warning: Maintain a safety distance of 15m. If approached, switch off
the equipment immediately. Always keep in mind that the user of the equipment
is responsible for accidents involving other persons or their property.
· Important: Danger of poisoning. Emissions, fuels and lubricants are toxic.
Do not inhale emissions.
· The powered equipment will create toxic exhaust fumes as soon as the engine
is started.
Never work in enclosed rooms or in rooms with poor ventilation.
Before using
· Always wear sturdy, non-slip footwear and
long trousers when mowing. Never mow barefoot or in sandals.
· Check the ground on which the equipment
will be used and remove all objects that could be caught up and catapulted
away.
· Warning: Petrol is highly flammable! There-
fore: – Only store petrol in containers designed to hold petroleum-based
liquids. – Only refuel out in the open and do not smoke during the refuelling
process. – Always refuel before starting the engine. Do not open the fuel tank
cap and do not refuel while the engine is running or when the equipment is
hot. – If petrol has overflowed, do not under any circumstances attempt to
start the engine. Instead, remove the equipment from the affected area. Avoid
starting the engine until the petrol fumes have completely evaporated. – For
safety reasons, the petrol tank and the tank cap must be replaced if they are
damaged.
· Replace defective silencers. · Before using the scythe, visually inspect it
to ensure that the blade, mounting bolts and the entire cutting apparatus are
in good working order (i.e. not worn out or damaged). To prevent any
imbalance, replace worn out or damaged blades and mounting bolts as a set only
(if applicable).
Handling (operation, storage, monitoring)
· Wear close-fitting work clothing which is in
good condition and which offers protection, such as long trousers, sturdy work
shoes, hard-wearing gloves, a helmet, a face mask or goggles to protect your
eyes, and good quality cotton wool in your ears or some other ear protectors
to reduce the noise.
· Store the equipment in a safe place. Open the
petrol tank cap slowly to release any pressure that may have formed in the
petrol tank. To prevent the risk of fire, move at least 3 meters from the
refueling area before you start the equipment.
· Switch off the equipment before you put it
down.
· Always hold the equipment firmly in both
hands. Your fingers and thumbs should be wrapped around the handles.
· Ensure that all screws and connecting elements are secure. Never use the
equipment
if it has not been properly adjusted or has not
been fully or safely assembled.
· Make sure that the handles are clean and dry
and that there is no petrol mixture on them.
· Set the line spool to the required height. Avoid
touching small objects such as stones with
the line spool.
· When carrying out mowing work on a slope
always stand at a lower level than the cutting
tool. Never cut or trim on a smooth, slippery
hill or slope.
· Keep all parts of your body and items of
clothing away from the line spool when you
start the engine and when the engine is run-
ning. Before you start the engine ensure that
the line spool will not strike an obstacle.
· Always switch off the engine before working
on the cutting tool.
· Store the equipment and accessories in
a safe place protected from naked flames
and heat/spark sources such as gas geyser
heaters, tumble driers, oil stoves or portable
radiators, etc.
· Keep the guard hood, line spool and engine
clear of mowing debris at all times.
· Only adequately trained people and adults
may use, adjust and maintain the equipment.
· If you are not familiar with the equipment,
practice handling it with the engine off.
· Always check the site you want to mow before
you begin your work. Solid objects such as
pieces of metal, bottles, stones, etc. can be
catapulted away and cause serious injuries
and permanent damage to the equipment. If
you touch a solid object with the equipment
by mistake, switch off the engine immediately
and check the equipment for signs of dama-
ge. Never use the equipment if it is damaged
or defective.
· Always operate the equipment in its high
speed range for trimming and cutting. Do not
let the engine run at low speed at the start of
mowing or during trimming work.
· Never hold the line spool above knee height
when the equipment is in operation.
· Do not use the equipment if other people or
animals are in the immediate vicinity. Keep
a minimum distance of 15 meters between
yourself and other people or animals when
mowing. Keep a distance of 30 meters if you
are mowing down to the ground.
If it is used for a lengthy period, the vibrations it causes in the hands of
the user may result in circulation problems (hand-arm vibration syndrome).
White finger syndrome is a vascular disease that involves seizure-like spasms
of the fingers and toes. The affected areas are no longer sufficiently
supplied with blood and therefore appear extremely pale. The frequent use of
vibrating equipment may trigger nerve damage in people with an impaired
circulation (for example smokers, diabetics). Should you observe any unusual
impairments, interrupt your work immediately and consult a doctor. Follow
these instructions in order to reduce the dangers:
· Keep your body and in particular your hands
warm when working in the cold.
· Take regular breaks and move your hands
to stimulate the blood circulation during the breaks.
· Ensure that the equipment makes the least
possible vibration through regular maintenance and solid parts on the
equipment.
Additional instructions
· Do not use any fuel other than that recom-
mended in the operating instructions. Always follow the instructions in the
section ,,Fuel and oil”. Do not use petrol that has not been mixed correctly
with 2-stroke oil. Otherwise there is a risk of causing permanent damage to
the engine and of voiding the manufacturer`s guarantee.
· Do not smoke while refueling or using the
equipment.
· Never use the equipment without the exhaust
pipe.
· Do not touch the exhaust pipe with your
hands or body. Hold the equipment so that your fingers and thumbs are wrapped
around the handled
· Do not use the equipment in an uncomfortab-
le posture, off balance, with extended arms or with only one hand. Always use
both hands on the equipment and wrap your fingers and thumbs around the
handles.
· Always keep the line spool on the ground
whilst the equipment is in operation.
· Use the equipment only for the purpose for
which it is intended, such as trimming and mowing weeds.
· Do not use the equipment over a lengthy peri-
od of time – take regular breaks.
– 32 –
Anl_GC_MM_52_I_AS_SPK9_1.indb 32
28.02.2024 07:31:58
GB
· Do not use the scythe if you are ill or tired or
under the influence of alcohol or drugs.
· Use the equipment only when the guard hood
is fitted and in good working order.
· Any modifications to the product may place
your personal safety at risk and cause the
manufacturer’s warranty to be voided.
· Never use the equipment near inflammable li-
quids or gases, neither in enclosed rooms nor
outdoors. Explosions and/or fire may result.
· Do not use any other cutting tools. For your
own safety you must use only the accessories
and attachments which are listed in the ope-
rating instructions or which are recommended
or specified by the manufacturer. The use of
cutting tools or accessories other than those
recommended in the operating instructions
or catalog may place your personal safety at
risk.
· Wear sturdy shoes with non-slip soles. · Always ensure that you have safe
footing
while using the equipment, particularly if you
are using a platform or ladder.
Safety precautions for handling the blade
· Take not of all warnings and instructions rela-
ting to operating and fitting the blade.
· The blade can recoil suddenly from objects if
it cannot cut or mow through them. This can
cause injuries to the arms or legs. Keep by-
standers and animals at least 15 meters away
from where you are working. If the equip-
ment strikes a foreign body, stop the engine
immediately and wait for the blade to come
to a standstill. Check the blade for signs of
damage. Always replace the blade if it is bent
or cracked.
· The blade is liable to catapult away objects
with high force. This can cause blindness or
injuries. Wear protection on your eyes, face
and legs. Always remove objects from your
working area before you use the blade.
· Carefully check your machine and its fittings
for signs of damage every time before use.
Do not use the equipment unless all the blade
fittings are installed correctly.
· When you release the throttle lever, the blade
will continue to rotate and will only gradually
come to a standstill. A blade which is in the
process of rotating to a standstill can cause
you or bystanders injuries through cutting.
Before you start any work on the blade, switch
off the engine and ensure that the blade has
come to a standstill.
· The danger zone has a radius of 15 meters.
Bystanders may suffer blindness or injuries.
Keep a distance of 15 meters between your-
self and other people or animals.
Special safety instructions for chainsaws
· When the chainsaw is running, make sure
that you keep all parts of your body away from
the chain. Before you start up the saw, make
sure that the chain is not touching anything.
When you are working with a chainsaw, a sin-
gle moment of carelessness is all it takes for
clothing or parts of your body to get caught
on the chain.
· Do not use the chainsaw while up a tree unless you are specially trained to
do this. You
risk injuring yourself if you use the chainsaw
incorrectly while up a tree.
· When cutting through a branch which is under
tension, expect it to recoil. When the tension
in the wood fibers is released, the cut branch
may hit you and/or wrench the chainsaw out
of your control.
· Carry the chainsaw with the chain stationary
and the chain bar facing backwards. Always
fit the safety guard when transporting the
chainsaw or putting it into storage. Careful
handling of the chainsaw reduces the likelihood of accidental contact with the
chain
while it is running.
· Follow the instructions for lubrication, tensioning the chain tension and
replacing
accessories. A chain which is not properly
tensioned or lubricated can break or increase
the risk of kickback.
· Keep the handles dry, clean and free from oil
and grease. Greasy or oily handles are slip-
pery and will result in loss of control.
· Saw only wood. The chainsaw must be used
only to perform the work for which it is intended. For example: Never use the
chainsaw
to cut plastic, brickwork, or building materials
which are not made of wood. Use of the
chainsaw to perform any work other than that
for which it is intended can create dangerous
situations.
· Hold the saw firmly with both hands, with
your fingers and thumbs wrapped around the
handles. Steady yourself with your body and
arms in a position in which you can control
the kickback forces. With the right precautions, an operator can control the
kickback
forces. Never let go of the chain saw.
· Always use the replacement chain bars and
chains specified by the manufacturer. Using
the wrong replacement chain bars or chains
may cause the chain to break or can result in
kickback.
· Follow the manufacturer`s instructions for
sharpening and maintaining the saw chain.
The risk of kickback is increased if the depth
limiter is set too low.
· Take special care when cutting undergrowth
and young trees. The thin material can become caught in the chain and whip
back towards you or make you lose your balance.
· Take care not to cut into the ground, metal
fences or similar unsuitable items and mate-
rials.
· We recommend that people who are using
a chainsaw for the first time should arrange
for a well-versed person to instruct them
on how to work with the chainsaw and the
safety equipment, for example in the form of
practical exercises (cutting wood on a sawing
trestle, etc.).
· Keep your working area free of obstacles and
ensure that you have adequate freedom of
movement. Do not work in constricted areas
in which you could get too close to the run-
ning chain.
· Keep your working area tidy and free of off-
cuts and other obstacles over which you
could stumble.
· Take care to maintain a steady foothold. Use
the chainsaw only on flat surfaces where you
have a firm footing. Never work on ladders or
on slippery surfaces on which you could lose
your balance and control of the chainsaw.
· Before you start felling branches:
Make sure that there is nobody within a range
of at least two and a half times the length of
the branch.
· Take the weather conditions into account
when felling trees. Do not fell trees in strong
or gusting wind. Do not fell trees in frosty
conditions or on frozen, icy ground. Do not fell
trees in rain or if visibility is poor.
· Comply with local regulations. · Always hold the chainsaw with your right
hand on the rear handle and your left hand on
the front handle. Holding the chainsaw with
your hands in the wrong positions increases
the risk of injury and must therefore be avoided.
· Wear safety goggles and ear protection.
Other safety equipment for the head, hands,
legs and feet is recommended. Correct safety
equipment reduces the risk of injury caused
by catapulted foreign bodies or in the event of accidental contact with the
chain.
· Always maintain a steady standing position
and work with the chainsaw only if you are standing on a solid, safe and flat
surface. Slippery or unsafe surfaces such as ladders can cause you to lose
your balance or control over the chainsaw.
· Plan an escape route from falling trees or
branches in advance. Make sure that this escape route is free of obstacles
which could restrict or prevent free movement. Keep in mind that freshly cut
grass or bark is slippery.
· Ensure that somebody is in the vicinity (but at
a safe distance) in case of an accident.
· When the chain is moving, do not let the tip
of the chain bar come into contact with any objects.
· Start sawing only after the chain has reached
full speed.
· Never try to target a previous cut. Always start
a new cut.
· Watch out for moving branches or other
forces which could interfere with a cut and impact with the chain.
· Never try to cut a branch with a larger diame-
ter than the cutting length of the equipment.
· Contact your local authorities for information
regarding minimum age requirements for operating the equipment.
· Keep the equipment at a minimum distance
of 10 meters from overhead power cables.
Causes of kickback and how to avoid it: Kickback can occur if the tip of the
chain bar touches an object or if the wood bends and jams the chain in the
cut. In some cases contact with the bar tip can result in an unexpected
backwards reaction in which the chain bar is catapulted upwards towards the
operator.
If the chain becomes jammed on the top edge of the chain bar, the bar may kick
back suddenly in the direction of the operator.
Any of these reactions can result in you losing control over the saw and
possibly in you suffering serious injuries. Therefore you should not rely
solely on the safety equipment fitted to the chainsaw. Whenever you use a
chainsaw you should always take various precautions in order to avoid
accidents and injuries.
Kickback is the result of a tool being used incorrectly or wrongly. It can be
prevented by suitable precautions, as described below:
· Hold the saw firmly with both hands, with
your fingers and thumbs wrapped around the handles. Steady yourself with your
body and arms in a position in which you can control the kickback forces. With
the right precautions, an operator can control the kickback forces. Never let
go of the chain saw.
· Avoid abnormal working postures. This will
prevent accidental contact with the tip of the chain bar and enables better
control of the chainsaw in unexpected situations.
· Always use the replacement chain bars and
chains specified by the manufacturer. Using the wrong replacement chain bars
or chains may cause the chain to break or can result in kickback.
· Follow the manufacturer`s instructions for
sharpening and maintaining the saw chain. The risk of kickback is increased if
the depth limiter is set too low.
Special safety information for hedge trimmers
· Make sure you keep all parts of your body
away from the blades. Never attempt to remove cuttings with the blade running
or to hold material you want to cut. Always switch off the equipment before
attempting to remove any jammed cuttings. A single moment of carelessness when
using the hedge trimmer can result in serious injuries.
· Carry the hedge trimmer by its handle
and make sure the blades have stopped. Always fit the protective cover when
transporting the hedge trimmer or putting it into storage. Careful handling of
the equipment reduces the likelihood of injury by the blades.
a) THIS HEDGE TRIMMER CAN CAUSE SERIOUS INJURIES. Carefully read the
instructions on proper handling, preparation, maintenance, switching on and
switching off of the hedge trimmer. Familiarize yourself with the controls and
adjustments and proper operation of the hedge trimmer.
b) Children must never be allowed to use the hedge trimmer.
c) Take care near overhead power cables. d) Do not use the hedge trimmer when
people
are nearby, particularly children.
e) Always make sure that the hedge trimmer is in a correct working position
before you start the engine.
f) Always ensure that you have safe footing while using the hedge trimmer,
particularly if you are using a platform or ladder.
g) Always make sure that all the handles and safety equipment are fitted when
you are using the hedge trimmer. Never attempt to use an incomplete hedge
trimmer or one that has been improperly modified.
h) Make yourself familiar with your surroundings and watch for possible
dangers that you may not be able to hear due to the noise generated by the
hedge trimmer.
i) Wear eye, hearing and head protection. j) Switch off the engine prior to:
– Cleaning or removing a blockage – Carrying out inspections, maintenance or
other work on the hedge trimmer – If the hedge trimmer is left unattended
· Before you start trimming hedges, check that
there are no concealed objects, for example wire fences, in the hedge.
· Hold the hedge trimmer correctly, for example
with both hands if it is fitted with two handles.
· If the cutting mechanism becomes jammed
in thick branches, etc., stop using the hedge trimmer immediately.
· Proper inspection and maintenance of the
hedge trimmer is required at regular intervals. Damaged blades should only be
replaced as pairs. If the trimmer is damaged by falling or impact, it must be
inspected by a qualified person.
· Do not use the machine if it has a damaged
or excessively worn cutter.
· Ensure that all handles and protective equip-
ment are properly fitted when you are using the hedge trimmer.
Keep this safety information in a safe place.
Explanation of the warning signs on the equipment (Fig. 19): 1. Warning! 2.
Read the directions for use before operating
the equipment. 3. Wear safety goggles, a face guard and ear
protection. 4. Wear sturdy, non-slip footwear. 5. Wear safety gloves. 6.
Protect the equipment from rain and damp. 7. Be careful of objects being
thrown out! 8. Always switch off the equipment and pull out the spark boot
plug before carrying out any maintenance work. 9. All bystanders must be kept
at least 15 m from the machine. 10. The equipment continues to rotate! 11.
Caution: Hot equipment parts. Keep your distance. 12. Add a little grease
(gear grease) after every 20 hours in operation! 13. Beware of recoil! 14. Do
not use any saw blades. 15. Electric shock can cause fatal injury. Keep a
distance of at least 10 m from power cables.
Layout and items supplied
2.1 Layout (Fig. 1-13) 1. Connecting piece for long handle 2. Engine unit 2a. Long handle for trimmer/scythe 2b Long handle for pole-mounted pruner 2c Long handle for high hedge trimmer 2d Adapter 3. Handle 3a. Steady grip 4. Pull cord 5. Choke lever 6. Petrol tank 7. Fuel pump ,,primer” 8. Air filter housing cover 9. On/Off switch 10. Air filter 11. Throttle lever 12. Throttle lock 13. Line spool with cutting line 14. Cutting line guard hood 15. Cutting blade guard hood 16. Spark plug connector 17. Harness 18. Cutting blade 18a. Cutting blade guard 19. Cutter rail 20. Spark plug connector cover 21. Handle screw M6 22. Carrier plate 23. Pressure plate 24. Pressure plate cover 25. Nut M10 (left-hand thread) 26. Oil/petrol mixing bottle 27. Spark plug wrench 28. Saw chain 29. Hexagon key 4 mm 30. Hexagon key 5 mm
31. Open-ended wrench size 8/10 32. Cutter guard 33. Hedge trimmer guard 34.
Adjuster lever 35. Hexagon key 3 mm
2.2 Items supplied Please check that the article is complete as specified in
the scope of delivery. If parts are missing, please contact our service center
or the sales outlet where you made your purchase at the latest within 5
working days after purchasing the product and upon presentation of a valid
bill of purchase. Also, refer to the warranty table in the service information
at the end of the operating instructions.
· Open the packaging and take out the equip-
ment with care.
· Remove the packaging material and any
packaging and/or transportation braces (if available).
· Check to see if all items are supplied. · Inspect the equipment and
accessories for
transport damage.
· If possible, please keep the packaging until
the end of the guarantee period.
Danger! The equipment and packaging material are not toys. Do not let children
play with plastic bags, foils or small parts. There is a danger of swallowing
or suffocating!
· Engine unit · Long handle for trimmer/scythe · Long handle for pole-mounted
pruner · Long handle for high hedge trimmer · Adapter · Steady grip · Line
spool with cutting line · Cutting line guard hood · Cutting blade guard hood ·
Harness · Cutting blade · Cutting blade guard · Cutter rail · Carrier plate ·
Pressure plate · Pressure plate cover · Nut M10 (left-hand thread) ·
Oil/petrol mixing bottle · Spark plug wrench · Saw chain · Hexagon key 3 mm ·
Hexagon key 4 mm
Hexagon key 5 mm · Open-ended wrench size 8/10 · Cutter guard · Safety goggles · Original operating instructions
Proper use
The power scythe (using the cutting blade) is designed for cutting young
trees, strong weeds and undergrowth. The power trimmer (using the line spool
with cutting line) is designed for cutting lawns, grassed areas and small
weeds. The operating instructions as supplied by the manufacturer must be
obeyed to ensure that the equipment is used properly. Any use which is not
expressly permitted in these instructions may result in damage to the
equipment and place the user in serious danger. Be sure to observe the
restrictions in the safety information.
The pole-mounted petrol-powered pruner is designed for lopping off tree
branches. It is not suitable for extensive sawing work, felling trees or
sawing any materials other than wood.
This hedge trimmer is suitable for cutting hedges, bushes and shrubs.
The equipment is to be used only for its prescribed purpose. Any other use is
deemed to be a case of misuse. The user / operator and not the manufacturer
will be liable for any damage or injuries of any kind caused as a result of
this.
Danger! Due to the high risk of bodily injury to the user, the petrol power
scythe is not allowed to be used to clean paths or to chop up tree and hedge
clippings. Similarly, the petrol power scythe must not be used to level out
high areas such as molehills. For safety reasons, the petrol power scythe must
not be used as a drive unit for other work tools or toolkits of any kind.
Please note that our equipment has not been designed for use in commercial,
trade or industrial applications. Our warranty will be voided if the machine
is used in commercial, trade or industrial businesses or for equivalent
purposes.
Technical data
Engine unit: Engine type.. 2-stroke engine, air-cooled, chrome cylinder Engine
power (max.) ……………….1.5 KW / (2 HP) Displacement …………………………………. 51.7 cm3
Engine idling speed ……………..3000 +- 400 min-1 Max. engine speed………………………….9600
min-1 Ignition ………………………………………….Electronic Drive ………………………………….Centrifugal
clutch Weight (empty tank without accessories) ……4 kg Petrol tank
capacity………………….. 900 cm³ (0.9 l) Spark plug ……………………………………….. L8RTC
Scythe: Weight (empty tank)………………………………7.9 kg Max. scythe speed………………………….7200
min-1 Engine speed ………………………………..9600 min-1 Cutting circle Ø of
blade…………………….. 255 mm Blade type: ………………… iSC Art. No.: 34.052.30
Trimmer: Weight (empty tank)………………………………7.8 kg Max. trimmer speed
………………………..7000 min-1 Engine speed ………………………………..9300 min-1 Cutting circle Ø
………………………………… 420 mm Line diameter …………………………………… 2.4 mm Line spool type:
…………… iSC Art. No.: 34.050.86
High hedge trimmer: Weight (empty tank)…………………………….8.34 kg Engine speed
………………………………..9600 min-1 Cuts per minute …………………………………… 1527 Cutting length
………………………………….. 395 mm Cutter rail length……………………………….. 430 mm Tooth spacing
……………………………………. 31 mm Max. cutting thickness ………………………… 23 mm
Pole-mounted pruner: Weight (empty tank)…………………………….7.85 kg Engine speed
………………………………..9600 min-1 Cutting length …………………….. 255 mm (10 inch) Max.
cutting speed ……………………………21.3 m/s Oil tank capacity ……………………120 cm3 (120 ml)
Chain ………………………………… Oregon 91P040X Cutter rail …………………….. Oregon 100SDEA318
Danger! Sound and vibration LpA sound pressure level …………………… 97 dB(A) KpA
uncertainty …………………………………. 3 dB(A) LWA sound power level …………………… 114 dB(A)
KWA uncertainty …………………………………. 3 dB(A)
Wear ear-muffs. The impact of noise can cause damage to hearing.
Operation Vibration emission value ah = 6.0 m/s2 K uncertainty = 1.5 m/s2
Keep the noise emissions and vibrations to a minimum.
· Only use appliances which are in perfect working order.
· Service and clean the appliance regularly. · Adapt your working style to
suit the appliance. · Do not overload the appliance. · Have the appliance
serviced whenever necessary.
· Switch the appliance off when it is not in use. · Wear protective gloves.
Assembly
5.1 General information
5.1.1 Fitting the steady grip (Fig. 3) Fit the steady grip (Item 3a) as shown
in Figure 3. Do not tighten the screws until you have set the perfect working
position with the carrying strap. The steady grip should be aligned as shown
in Figure 1. To dismantle, proceed in reverse order.
5.1.2 Fitting the long handle (Fig. 4a 4b) Pull the locking lever (A) and
push the long handle (Fig. 4b/Item 2a) into the connecting piece of the engine
unit. While doing so, make sure that the drive shafts on the inside of the
long handle slide into each other (turn the spool head slightly, for example,
if required). The lug of the locking lever (A) must latch into the hole (B).
Now tighten the handle screw (21) as shown in Figure 4b.
5.2 Trimmer/scythe
5.2.1 Fitting the blade guard hood (Fig. 5a-5b) Important: The cutting blade
guard hood (Item 15) must be fitted when you want to work with the cutting
blade. The guard hood for the cutting blade must be installed as shown in
Figures 5a-5b.
5.2.2 Fitting/Replacing the cutting blade The fitting of the cutting blade is
shown in Figures 6a 6g. To dismantle, proceed in reverse order.
· Important! The cutting blade has sharp edges.
You therefore need to wear protective gloves when handling the cutting blade.
· Fit the carrier plate (22) onto the spline shaft
(Fig. 6b)
· Securely fit the cutting blade (18) on the cover ring (Fig. 6c)
· Place the pressure plate (23) over the thread
of the spline shaft (Fig. 6d).
· Plug on the cover of the pressure plate (24)
(Fig. 6e).
· Look for the hole in the carrier plate, line up
with the notch underneath, lock with the supplied hexagon key (29), and
tighten the nut (25) (Fig. 6f/6g). Note: Left-hand thread
· Remove the cutting blade guard (Item 18a)
before starting work.
5.2.3 Fitting the cutting line guard hood to the blade guard hood
Important: The cutting line guard hood must be additionally fitted if you want
to work with the cutting line (Fig. 7a/Item 14). The guard hood for the
cutting line must be installed as shown in Figures 7a 7b. A blade (Fig.
7a/Item F) on the underside of the guard hood automatically cuts the cutting
line to the optimum length. This is covered by a guard (Fig. 7a/Item F).
Remove the guard before you start working and replace it when you have
finished working.
5.2.4 Fitting/Replacing the line spool The fitting of the line spool is shown
in Figure 7c7d. To dismantle, proceed in reverse order.
Look for the hole in the carrier plate, line up with the notch beneath it,
lock with the supplied hexagon key (29), and screw the line spool onto the
thread. Note: Left-hand thread
Setting the cutting height
· Fit the carrying strap as shown in Figures 8a- 8c.
· Hook the equipment to the carrying belt (Fig. 8d).
· Adjust to the perfect working and cutting position using the various strap
adjusters on the carrying strap (Fig. 8e).
· In order to establish the optimum length of
the carrying strap, you should then make a few swinging movements without
starting the engine (Fig. 10a).
The carrying strap is fitted with a quick-release mechanism. Pull the red
strap section (Fig. 8f) if you need to remove the strap quickly.
Warning: Always use the strap when working with the equipment. Attach the
strap as soon as you have started the engine and it is running in idle mode.
Switch off the engine before you take off the carrying strap.
5.3 Pole-mounted pruner
Important! Do not start the chainsaw until it has been fully assembled and the
chain tension has been adjusted. Always wear protective gloves when working on
the chainsaw to protect yourself against injury.
Important! Depending on the required working height, the adapter (Item 2d) can
be fitted between the engine unit (Item 2) and the long handle (2b), as
described in 5.1.2.
5.3.1 Fitting the cutter rail and saw chain (Fig. 9a-9f)
Tools required: Open-ended spanner (Item 31) Remove the chain wheel cover
(Fig. 9c/Item K) by undoing the fastening screw (Item J). Lay the chain (Item
28) as shown into the groove which runs around the cutter rail (Item 19). Note
the alignment of the chain teeth (Fig. 9b). Place the chain round the chain
wheel (Item I). Make sure that the teeth of the chain engage securely in the
chain wheel. Insert the cutter rail as shown in Fig. 9 into the mount at the
gear unit. The cutter rail must be hooked into the chain tensioning bolt (Item
H). Fit the chain wheel cover.
Important! Do not fully tighten the fastening screw until after you have
adjusted the chain tension (see section 5.3.2).
5.3.2 Tensioning the saw chain (Fig. 9d-9f) Important! Always pull out the
spark boot plug before performing any checks or adjustments. Undo the
fastening screw (Item J) of the chain wheel cover by a few turns (Fig. 9c).
Adjust the chain tension with the chain tensioning screw (Fig. 9e/Item L).
Turning the screw clockwise increases the chain tension, turning it
counterclockwise decreases the chain tension. The chain tension is correct
when the chain can be lifted by about 2 mm at the center of the cutter rail
(Fig. 9d). Tighten the fastening screw of the chain wheel cover (Fig. 9f).
Important! All the chain links must lie properly in the guide groove of the
cutter rail.
Notes on tensioning the chain: The chain must be properly tensioned to ensure
safe operation. When the saw chain can be raised by around 2 mm in the middle
of the cutter bar, you know that the chain tension is ideal. During cutting,
the temperature of the chain rises and its length changes. It is important
therefore to check the chain tension at least every 10 minutes and to adjust
it again as required. This applies in particular to new saw chains. When you
have finished working, slacken the chain again as it will shorten when it
cools down. This will help to prevent damage to the chain.
5.4 Hedge trimmer
Important! The hedge trimmer is ready for use straight away after the long
handle (Item 2c) has been fitted (see section 5.1). Depending on the required
working height, the adapter (Item 2d) can be fitted between the engine unit
(Item 2) and the long handle (2c), as described in 5.1.2.
Before using the equipment
6.1 General information
Each time before use, check the following :
· That there are no leaks in the fuel system. · That the equipment is in
perfect condition and
that the safety devices and cutting devices are complete.
· That all screws are securely fastened. · That all moving parts move
smoothly.
6.1.1 Fuel and oil Recommended fuels Use only a mixture of unleaded petrol and special 2-stroke engine oil. Mix the fuel mixture as indicated in the fuel mixing table. Note: Do not use a fuel mixture which has been stored for longer than 90 days. Note: Never use 2-stroke oil with a recommended mixing ratio of 100:1. The manufacturer’s warranty will be voided in case of engine damage due to inadequate lubrication. Warning: Only use containers designed and approved for the purpose to transport and store fuel. Pour the correct quantities of petrol and 2-stroke oil into the mixing bottle (see scale printed on the bottle). Then shake the bottle well.
6.1.2 Fuel mixing table Mixing procedure: 40 parts petrol to 1 part oil
Petrol (E10)
2-stroke oil
1 liters
25 ml
5 liters
125 ml
6.2 Pole-mounted pruner
Chain lubrication Important! Never operate the chain if it is not lubricated with saw chain oil. Use of the chainsaw without saw chain oil or if the oil level is below the ,,min” mark will damage the chainsaw.
Important! Be aware of the temperature conditions: Different lubricants with completely different viscosities are required at different ambient temperatures. At lower temperatures you will need low viscosity oils in order to achieve a sufficient lubricating film. However, if the same low viscosity oil is used during the summer it will become even thinner due to the ambient temperatures alone, and as a result the lubricating film could break down, causing the chain to overheat and become damaged. In addition, the chain oil would burn and produce unnecessary pollutants.
Filling the oil tank (Fig. 9e): Place the chainsaw on a flat surface. Clean the area around the oil tank cap (Item M) and then open it. Fill the tank (Item M) with saw chain oil. In the process, make sure that no dirt enters the tank, as this could cause the oil nozzle to become blocked. Close the oil tank cap.
Operation
Please note that the statutory regulations governing noise abatement may
differ from one location to another. Before starting up the equipment remove
the protective caps from the cutting blade. Practice all the work steps with
the engine switched off before you start to use the equipment.
7.1 Starting the engine when cold Fill the tank with an adequate amount of
petrol/oil mix. See ,,Fuel and oil”. 1. Set the equipment down on a hard,
level sur- face. 2. Press the fuel pump (primer) (Fig. 1/Item 7) ten times. 3.
Set the On/Off switch (Fig. 1/Item 9) to ,,I”. 4. Set the choke lever (Fig.
1/Item 5) to ” “. 5. Hold the equipment securely and pull out the
starter cable (Fig. 1/Item 4) until you feel it begin to resist. Then tug
sharply on the starter cable twice. 6. Set the choke lever (Fig. 1/Item 5) to
” “. 7. Hold the equipment securely and pull out the starter cable (Fig.
1/Item 4) until you feel it begin to resist. Then tug sharply on the starter
cable 4 times. The equipment should start. Note: Never allow the starter line
to snap back. This may result in damage. Once the engine has started, allow
the equipment to warm up for 10 seconds. Warning: The cutting tool starts to
operate when the engine is started. 8. If the engine does not start up, repeat
steps 4-8 above. Please note: If the engine does not start up even after
several attempts, read the Engine troubleshooting section. Please note: Always
pull out the starter cable in a straight line. If it is pulled out at an
angle, friction will occur on the eyelet. As a result of this friction, the
cable will become frayed and will wear faster. Always hold the starter handle
when the cable retracts. Never allow the cable to snap back when it has been
pulled out.
7.2 Starting the engine when warm (The equipment has been idle for less than
15-20 min.) 1. Set the equipment down on a hard, level sur-
face. 2. Switch the On/Off switch to ,,I”. 3. Hold the equipment firmly and
pull out the
starter cable until you feel it start to resist. Then tug sharply on the
starter cable. The equipment should start after 1-2 tugs. If the equipment
does not start after 6 pulls, repeat steps 1 7 of the procedure for starting
the engine from cold.
7.3 Switching off the engine
ventilation. Remove the remnants carefully using a screwdriver or the like.
Different cutting methods When the equipment is correctly assembled it will
cut weeds and long grass in places which are difficult to access, e.g. along
fences, walls and foundations and also around trees. It can also be used for
,,mowing” down vegetation so that a garden can be better prepared or a certain
area cleared down to the soil.
Please note: Even if it is used carefully, cutting around foundations, stone
or concrete walls, etc. will result in the line suffering above normal wear.
Emergency Off procedure: If it becomes necessary to stop the equipment
immediately, set the ON/OFF switch to “Stop” or “0”
Normal procedure: Let go of the throttle lever and wait until the engine has
changed to idling speed. Then set the ON/ OFF switch to “Stop” or “0”.
7.4 Practical tips Practice all the work steps with the engine switched off
before you start to use the equipment. When the engine is running and the
throttle lever (Item 11) is not actuated, the engine will run at idle speed
and the cutting tool will not move. The cutting tool only starts moving after
the throttle lever has been actuated.
8. Working with the petrol multifunction tool
8.1 Working with the petrol power scythe
Extending the cutting line Warning! Do not use any kind of metal wire or metal
wire encased in plastic in the line spool. This may cause serious injuries to
the user. To extend the cutting line, run the engine at full speed and tap the
line spool on the ground. This will automatically extend the line. The blade
on the safety shield will cut the line to the appropriate length (Fig. 10b).
Note: Remove all grass and weed remnants at regular intervals to prevent the
shaft tube overheating. Lawn, grass and weed remnants become trapped under the
safety shield (Fig. 10c) and prevent the shaft tube from receiving adequate
Trimming/mowing Swing the trimmer from side to side in a scything motion.
Always keep the line spool parallel to the ground. Check the site and decide
which cutting height you require. Guide and hold the line spool at the
required height to obtain an even cut (Fig. 10d).
Low trimming Hold the trimmer right in front of you at a slight angle so that
the underside of the line spool is above the ground and the line strikes the
correct target. Always cut away from yourself. Never draw the trimmer towards
yourself.
Cutting along fences/foundations Approach wire mesh fences, lath fences,
natural stone walls and foundations slowly so that you can cut close to them
without striking the obstacle with the line. If, for example, the line strikes
stones, stone walls or foundations, it will wear or fray. If the line strikes
wire fencing, it will break.
Trimming around trees When trimming around tree trunks, approach slowly so
that the line does not strike the bark. Walk around the tree, cutting from
left to right. Approach grass or weeds with the tip of the line and tilt the
line spool forwards slightly.
Warning: Take extreme care during mowing work. When doing such work keep a
distance of 30 meters between yourself and other people or animals.
Mowing When mowing down to the ground you will cut all the vegetation. To do
this, set the line spool at an angle of 30° to the right. Place the handle in
the required position. Remember the increased risk of injury to the user,
watchers and animals, and the danger of damaging property due to objects (for
example stones) being thrown up (Fig. 10e).
Warning: Do not use the equipment to remove objects from footpaths, etc. The
equipment is a powerful tool and can throw small stones and other objects a
distance of 15 meters or more, causing injuries and damage to cars, houses and
windows.
Sawing The equipment is not suitable for sawing.
Jamming If the cutting blade jams as a result of attempting to cut vegetation
that is too dense, switch off the engine immediately. Remove the grass and
scrub from the equipment before you restart it.
Preventing recoil When you work with the blade, there is a risk of recoil if
it strikes solid objects such as tree trunks, branches, tree stumps, stones or
the like. This will throw the equipment backwards in the direction opposite to
the rotation of the tool. This can cause you to lose control of the equipment.
Do not use the blade near fences, metal posts, boundary stones or foundations.
For cutting dense stalks, position it as shown in Figure 10f to prevent
recoil.
8.2 Working with the pole-mounted pruner Preparations To ensure that you can
work safely, check the following points before every use:
minutes depending on the number of pauses in cutting and the loads involved.
Saw chain Tension of the chain, condition of the cutting elements: The sharper
the chain, the easier and more controllable it is to operate the chainsaw. The
same also applies to the chain tension. For greater safety you must check the
chain tension before your work and at least every 10 minutes during your work.
New chains in particular tend to expand more.
Safety clothing Always wear appropriate tight-fitting safety clothing such as
special trousers which protect against cuts, protective gloves and safety
shoes.
Hearing protection and protective goggles Wear a protective helmet with
integral face and hearing protection. This will offer protection against
falling branches and recoiling branches.
Safe working Never stand under the branch you want to saw. Use special caution
when working with branches under tension and splintering wood. Possible risk
of injury caused by falling branches and catapulting pieces of wood. When the
equipment is in operation, keep other persons and animals away from the danger
zone. The equipment is not protected from electric shock through contact with
high-voltage cables. Keep a minimum distance of 10 m from live cables.
Electric shock can cause fatal injury. When working on slopes always stand to
the upper or left or right side of the branch you want to cut. Hold the
equipment as close as possible to your body. This will help you to keep your
balance.
Condition of the chainsaw Before you start your work, inspect the chainsaw for
damage to the housing, the chain and the cutter bar. Never use a chainsaw
which is obviously damaged.
Oil container Level of oil in the oil container: Both before and during your
work make sure that there is always sufficient oil in the system. To avoid
damaging the chainsaw, never run the saw if there is no oil in the system or
if the oil drops below the ,,min” mark. On average, a single filling will last
around 10
Cutting techniques
· When removing branches, hold the equip-
ment at an angle of max. 60° to the horizontal
to avoid being hit by a falling branch (Fig.
11c).
· Start with the bottom branches on the tree. · This will make it easier for
the cut branches to
drop.
· After completing a cut, the weight of the saw
will abruptly increase for the operator as the
saw is no longer supported by the branch.
This can result in you losing control over the
saw.
· Remove the saw from the cut only with the saw chain still running. This will
prevent the saw from getting jammed.
· Never cut with the tip of the saw. · Never cut into the bulging branch
collar. This will prevent the tree from healing.
Sawing off smaller branches (Fig. 11a): Place the contact surface of the saw
onto the branch. This will prevent the saw from making jerky movements when
you begin a cut. Exerting slight pressure, guide the saw from the top to the
bottom through the branch.
Sawing off large and long branches (Fig. 11b): Carry out a relief cut when
working on large branches. Start by sawing through 1/3 of the branch diameter
(a) from the top to the bottom with the top side of the cutter rail. Then saw
towards the first cut (b) from the top to the bottom with the bottom side of
the cutter rail. Saw off long branches in several steps to keep control over
the impact location.
Kickback The term ,,kickback” describes what happens when the running chainsaw suddenly kicks upward and backward. Usually this is caused by contact between the tip of the cutter rail and the workpiece or by the saw chain becoming trapped. In the event of kickback, large forces occur suddenly and violently. As a result, the chainsaw usually reacts uncontrollably. This can often result in very serious injuries to the worker or persons in the vicinity. The risk of kickback is at its greatest when the saw is positioned for a cut in the region of the tip of the cutter rail, as the leverage effect is greatest there. It is therefore safest to position the saw as flat as possible.
Important!
· Make sure that the chain tension is always correctly adjusted.
· Only use a chainsaw if it is in perfect working order.
· Only work with a saw chain that has been properly sharpened in accordance
with the instructions.
· Never cut with the upper edge or the tip of the cutter rail.
· Always hold the chainsaw firmly with both hands.
Cutting wood which is under tension Special care is required when cutting wood
which is under tension. Cutting wood which is under tension can release the
tension, causing the wood to react out of control. In the worst case this can
result in severe and even fatal injuries. This type of work must be performed
only by specially trained persons.
In any case of possible damage (e.g. if a branch fall on the equipment, the
equipment has fallen over, etc.), check that the equipment is still in proper
working order for continued use. If not, contact customer service staff.
8.3 Working with the hedge trimmer Never allow the machine to run at low speed
for starting or for cutting.
Adjusting the angle of the cutting blade (Fig. 12a-12b)
Important! Switch off the engine before you make any adjustments. The cutting
blade can be tilted in order to ensure an ergonomic working position. Grip the
adjuster lever (Item 34) with your left hand. First actuate lever N with your
index finger and then lever O with your thumb. Place the cutting blade in the
required position. When levers N and O are released, the cutting blade will be
locked in position.
Cutting dense growth: The most effective method is to use wide, sweeping
movements, guiding the cutting edge of the blade straight through the
branches. A slight incline of the blade downwards in the direction of movement
will produce the best cutting results (Fig. 13a). It is recommended to tie a
guide line of string or the like along the hedge so that you cut the hedge to
a level height. The branches above it will be cut off.
Cutting the sides of a hedge: Cut the sides of a hedge with curve-shaped
movements from the bottom up (Fig. 13b). Important: For design reasons, the
engine might stall when the tank is not full and you use the equipment to cut
the sides of long hedges.
Maintenance
Always switch off the equipment and pull out the spark boot plug before
carrying out any maintenance work.
9.1 Maintenance of the engine unit
9.1.1 Maintenance of the air filter (Fig. 14a-14c)
Soiled air filters reduce the engine output by supplying too little air to the
carburetor. Regular checks are therefore essential. The air filter (10) should
be checked after every 25 hours of use and cleaned if necessary. If the air
contains a lot of dust, the air filter must be checked more frequently. 1.
Remove the air filter cover (Fig. 14a). 2. Remove the air filter (Fig.
14b/14c) 3. Clean the air filter by tapping it or blowing it
out. 4. Assemble in reverse order. Warning: Never clean the air filter with
petrol or inflammable solvents.
9.1.2 Maintenance of the spark plug (Fig. 15a-15c)
Spark plug sparking gap = 0.6mm. Tighten the spark plug with a torque of 12 to
15 Nm. Check the spark plug for dirt and grime after 10 hours of operation and
if necessary clean it with a copper wire brush. Thereafter service the spark
plug after every 50 hours of operation. 1. Remove the spark plug connector
cover (20)
as shown in Fig. 15a. 2. Pull out the spark plug connector (16). (Fig.
15b) 3. Remove the spark plug (Fig. 15c) with the
supplied spark plug wrench (27). 4. Assemble in reverse order.
9.1.3 Carburetor settings Warning! Settings on the carburetor may only be made
by authorized customer service personnel. To carry out any work on the
carburetor you must first remove the air filter cover as shown in Figures 14a-
14c.
Setting the throttle cable: If the maximum speed of the equipment drops over
time and you have ruled out all the other possible causes listed in section 12
,,Troubleshooting”, it may be necessary to adjust the throttle cable. First of
all check whether the carburetor opens fully when the throttle handle is
pressed right through. This is the case if the carburetor slide (Fig. 16a) is
completely opened when the throttle is fully activated. Figure 16a shows the
correct setting. If the carburetor slide is not completely open, it must be
adjusted.
The following steps are required to adjust the throttle cable:
· Undo the lock nut (Fig. 16b/Item C) a few turns.
· Undo the adjusting screw (Fig. 16a/Item D) until the carburetor slide is
completely open when the throttle is fully activated, as shown in Figure 16a.
· Retighten the lock nut.
9.1.4 Setting the idling speed Important! Set the idling speed when the
equipment is warm. Only an authorized service center is allowed to set the
idling speed. The start-up speed of the cutting tool must be at least 1.25
times the idling speed.
9.2 Maintenance of the trimmer/scythe
9.2.1 Replacing the line spool/cutting line 1. Dismantle the line spool (13)
as described in
section 5.2.4. Press the spool together (Fig. 17a) and remove one half of the
housing (Fig. 17b). 2. Take the line spool out of the line spool housing (Fig.
17c). 3. Remove any remaining cutting line. 4. Place the new cutting line in
the center and hang the loop which has formed into the recess in the spool
splitter (Fig. 17d) 5. Wind up the line counter-clockwise and under tension.
The spool splitter will separate the two halves of the line (Fig. 17e) 6. Hook
the last 15cm of the two ends of the line onto the opposite lying line holders
of the spool plate (Fig. 17f) 7. Thread the two ends of the line through the
metal eyelets in the line spool housing (Fig. 17c). 8. Press the line spool
into the line spool housing. 9. Pull the two line ends sharply to release them
from the line holders. 10. Cut the excess line to a length of around 13cm.
This will reduce the load on the engine when starting and warming up.
References
- Einhell Service
- Service.com is for sale | www.brandforce.com
- Einhell Service
- Strumenti di alta qualità per gli amanti del Fai da Te e del giardinaggio | Einhell.it
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>