tzumi 8632HD ColorStrip LED Lights User Guide
- June 3, 2024
- Tzumi
Table of Contents
tzumi 8632HD ColorStrip LED Lights
INTRODUCTION & FEATURES
Give your home living room a unique atmospheric twist with the AuraLED Mood light Color Strip. Designed with a safe adhesive backing, this colorful backlight can be fixed directly onto the back of your TV or computer screen, enhancing your home theater and easing light-induced fatigue. It fits screens up to 65″ and includes a wireless remote controller, which provides you with the freedom to customize your selection of 16 colors and find the pertest brightness, rhythm, and color scheme.
PACKAGE CONTENTS
- 1 6.5 Ft Color Strip
- 1 Wireless Remote Control
- User Guide
PRODUCT OVERVIEW
- To adjust size of the LED Light Strip, please cut along designated line as shown below
NOTE: Cutting anywhere else will result in partial or total damage to the LED Light Strip.
INSTALLATION
NOTE: Please make sure that the back surface of your TV is clean from dust, oils, or fingerprints before attempting to apply your Color Strip. Use an alcohol-based cleaning cloth to wipe the back of your TV.
-
Locate the USB port on the back of your TV. If your TV does not have a USB port, you may use any other USB power source.
-
Make sure that you are satisfied with the coverage area of the Color Strip prior to peel ink off the adhesive tape. Make sure that the USB cable is placed near the USB port and has enough slack to reach safely. The Remote Receiver must also be visible in order to work properly.
-
Peel off the backing of the strip to expose the adhesive.
-
Apply to the cleaned surface on the back of TV. Press down for a couple of seconds to secure.
-
Connect the Color Strip with the USB Cable and insert the cable into the USB port.
-
Once connected, remove the protective plastic strip from remote control to activate the battery.
-
Press the ON button to turn on the Color Strip.
-
Refer to the color combinations settings on the remote to customize your Color Strip.
ASSEMBLY
- Connect the Color Strip with the USB cable .
See below tor suggested placement depending on your TV size:
These illustrations are for visual reference only. Color Strip placement will
vary depending on each individual unit.
WIRELESS REMOTE CONTROL
Buttons 1 and 2 can be used to control the brightness for the LED color buttons and change the speed for buttons 6,7,8,9.
- Brightness (Up)
- Brightness (Down)
- Power OFF
- Power ON
- LED Color Buttons -16 colors
- Flash Transition Effect
- Strobe Transition Effect
- Fade Transition Effect
- Smooth Transition Effect
When remote control operation becomes slow, it is time to change the battery.
*Compatible with CR2025-CR2032 battery types.
COLORSTRIP SPECS
- Input: SV/0.SA – 1;
- Power Consumption: 2.Sw – SW
- LED Chip: 5050, RGB
- Color: 16 colors with 4 Mood light settings
- LED Strip: 60 LED lights/ 6.5 ft (78″)
- Back Adhesive: Self adhesive
- Working Temperature: -4° – 113°F
- Working Humidity: 0% – 80% RH
CARE & IMPORTANT SAFEGUARDS
- Keep Color Strip away from flammable objects.
- Always make sure that all parts have been connected properly.
- Check to make sure the voltage of the power source (USB) is SV.
- Do not connect the Color Strip to the power source until all of the installations have been completed.
- Do not cut any part of the Color Strip or its connectors.
- Always make sure that the Remote Receiver is not covered or blocked. This will ensure proper operation using the remote control
- If this product malfunctions, please do not try to repair it yourself, take it to a qualified electrician.
If you have any other questions or issues with product use and/or care, please contact Tumi Technical Support at: support@tzumi.com or 1-855-GO-TZUMI.
Distributed by AuraLED. NY, NY 10016. © Copyright 2021. All Rights Reserved.
Made in Chine. Other trademarks and trade names are those of their respective
owners. Subject to change without prior notice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>