LUVION Icon Clear 70 Set Baby Monitors Instruction Manual

LUVION Icon Clear 70 Set Baby Monitors

PACKAGE CONTENTS

• 1 Baby unit
• 1 Parent unit
• 2 x AA NiMH 1300mAh rechargeable batteries for Parent unit (pre-installed)
• 2 adapters
• This user manual

PRODUCT OVERVIEW

Baby unit (Fig. 1)

1. Microphone
2. Power on/off , Press and hold to switch the power on or off .
3. Link indicator, Flashes orange when your monitor is trying to fi nd a link. Remains solid when the Parent and Baby units are linked to each other.
4. Power socket (on the back), For connecting to the mains power socket using the power adapter cable supplied.

Parent unit (Fig. 2)

1. Battery light, fl ashes if your battery is low, remains steady if your unit is charging.
2. Volume down, turns the speaker down.
3. Mute light, remains on when your Parent unit is on mute.
4. Power, Press and hold to turn the unit on or off .
5. Volume up, Turns the speaker volume up.
6. Link light, Flashes when your monitor is trying to fi nd a link. Remains solid when the Parent and Baby units are linked to each other.
7. Power socket (on the back), for connecting to the mains power socket using the power adapter cable supplied.

INTRODUCTION

Thank you for purchasing the Luvion Icon Clear 70 baby monitor. From now on you can always hear your baby. Make sure you always keep your original proof of purchase. For warranty cases you will always be asked to show a copy of your proof of purchase. For warranty claims you can contact the Luvion dealer or the local Luvion representative. More information can be found at www.luvion.com. This manual contains all the information you need, to be able to use this Luvion Icon Clear 70 baby monitor safely and with pleasure. Before using the baby monitor, we recom-mend that you read this manual carefully. We ask for your extra attention for the safety instruc-tions.

SAFETY INSTRUCTIONS

• WARNING: CHOKING HAZARD – Keep the adapter cables out of the reach of children! NEVER place the baby monitor or adapters within 1.5 meters of the crib / bed or a play-ground.
• Never use extension cables in combination with the adapters to prevent entanglement.
• Use only the originally supplied adapters. Use only on standard (100 ~ 240 volts AC) power points.
• If you travel abroad, check the voltage on your unit’s plugs match the local power output.
• This product is not a toy. Don’t let children play with it.
• The baby monitor is not suitable for use as a medical surveillance monitor.
• The baby monitor is not a substitute for parental supervision.
• Do not use the baby monitor in a damp environment or near water, such as in the bath-room, kitchen, laundry room or wet basement, etc.
• This product is only suitable for indoor use.
• It is important to fi rst check the range and condition of the baby monitor before fi rst use and then on a regular basis.
• Test the connection well when the baby monitor is moved.
• Use the baby monitor at a temperature between 10 °C and 40 °C, do not place the baby monitor in direct sunlight or at other heat sources such as radiators, candles, gas cooker, etc. Ensure there is suffi cient ventilation space around the baby monitor.
• Never dismantle the parent or baby unit yourself, this invalidates the warranty. This must be done by certifi ed personnel, contact the seller of the local distributor for this.
• Only replace the batteries with original Luvion batteries of the same type. Using the wrong batteries may damage your baby monitor.
• Make sure that the parent unit is fully charged on fi rst use. This guarantees an optimum battery life.
• Dispose of used batteries in accordance with local environmental regulations.

SETUP & USE

PARENT UNIT SETUP

Setting up

1. Plug one of the power cables into the socket on the back of the Parent unit. (fi g. 3)
2. Plug the other end of the cable into your mains wall socket and switch it on.
3. Activate the batteries by pulling the plastic tab away from the back of the Parent unit. (fi g. 5)
4. Leave the batteries to charge for 16 hours to reach maximum charge. When they are fully charged the battery light will show full charge.

Warning: Only use the power adapters supplied. Using incorrect power adapters may permanently damage your product.
Battery low alert on Parent unit
When the batteries on your Parent unit are running out, an alert will sound and the battery icon will fl ash. When this happens, you’ll need to charge the batteries.
If you ever need to remove the batteries, slide open the battery compartment cover and use the ribbon to push them out.
Warning: Always use rechargeable batteries in the Parent unit. Only use the type we’ve recommended – 2 x AA NiMH 1300mAh batteries. Charge the batteries as instructed in this user guide. The Parent unit can still be used when it’s charging.

BABY UNIT SETUP

Setting up

1. Plug the remaining power cable into the socket on the back of the Baby unit.
2. Plug the other end of the cable into your mains wall socket and switch it on. (fi g. 4)

Switching on and linking the Parent and Baby units

Before switching on, make sure the Parent and Baby unit are at least one metre from each other. Any closer and you might get audio feedback sounds.

1. Press and hold the button on the Baby unit until the orange Link indicator fl ashes.
2. Press and hold the button on the Parent unit until all the LEDs on the unit briefl y light up. The orange Link indicator will fl ash and then will remain steady when the units have linked.
3. When the units are linked, the orange Link indicator lights on the Parent and Baby units will stop fl ashing. When the lights stay steady, your monitor is ready to use.

Deciding where to put your units
The Baby unit should ideally be within 1 to 2 metres of your baby. Make sure both the Baby unit and mains power cable are connected securely and they’re out of baby’s reach. If the Parent and Baby units are too close together, you’ll hear a high-pitched noise. That’s because the units are designed to be put at a distance from one another, such as in separate rooms.

Important: The two units will need to be linked before you can start using them. If the link between the units is broken, the Link indicator lights will fl ash while they try to look for each other. After 30 seconds, if the link is still broken, the Link indicator lights will fl ash red. If the link is broken, check that:

• the mains power is plugged in and switched on at the Baby unit
• both units are switched on
• the batteries are charged in the Parent unit
• the Parent and Baby units are within range of each other (in ideal conditions, that’s up to 330 metres outdoors and 50 metres indoors).

USING YOUR LUVION ICON CLEAR 70 AUDIO BABY MONITOR

Switching the Baby unit on

1. Press and hold the button, the orange Link light fl ashes. When it’s fi nished linking, it’ll stop fl ashing and remain steady.
2. To switch off , press and hold the button again.

Switching the Parent unit on

1. Press and hold the button on your Parent unit. The LED lights will fl ash. The orange Link light will also fl icker on and off while the units are linking. When the units have found each other, your Parent unit will go back to its idle screen.
2. To switch off , press and hold the button again. All the lights will switch off .

Changing the loudspeaker volume on your Parent unit
You can change the volume using the + and – buttons. If you’ve muted the sound, the mute light will come on.
Note : The unit has fi ve volume levels plus Off (Mute). If you try to set the volume higher or lower than those, you’ll hear a beep.
List of tones
Your baby monitor can produce various tones. They have the following meaning:

TONE MEANING

Single tone| Confirmation (for example, saving a setting).
Fast double tone| Error (for example, trying to change the volume but already reached maximum).
Fast triple tone| System alert (for example, link lost or battery low).

You can turn off user alert tones by pressing any button on the Parent unit.

Resetting the units
Resetting either units means they’ll return to the settings they came with.

1. Make sure the unit you’re resetting is switched off .
2. Switch it back on again by pressing and holding the button down .
3. Within four seconds of turning the power back on, press and hold the – button for at least a second. You should only reset if you’re having problems with your baby monitor.

TROUBLESHOOTING

CARE & MAINTENANCE

• Use a soft, non-static or slightly damp cloth to clean the baby monitor.
• Never use the baby unit or parent unit in a wet or damp environment.
• Do not use or store in dusty or dirty areas.
• Do not store in warm places. High temperatures can adversely aff ect the life of the electronics and aff ect the plastic parts.
• Do not store in very cold places. This can cause moisture to damage the electronics.
• Leave the housing of the products closed. Opening the housing may damage the product and void the warranty.
• Do not drop the product and avoid violent shocks.

DISPOSAL OF PRODUCT & BATTERY

• Your baby monitor is classed as electrical or electronic equipment, so DO NOT put it in your normal rubbish bin. It’s all part of the Waste Electrical and Electronic Equipment (WEEE) Directive to recycle products in the best way
• Take these products to the collection points designated by the local authorities for the correct collection and processing of these products.

EU DECLARATION OF CONFORMITY

Luvion declares that the radio equipment type Luvion Icon Clear 70 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at: luvion.com/doc/icon- clear-70

Work Frequency
Transmitt Frequency (MHz): 1881.792-1897.344 MHz
Receive Frequency (MHz): 1881.792-1897.344 MHz

Luvion Premium Babyproducts Visit us at:
www.Luvion.com

References

• Babyfoon en Babycare Specialist - Luvion Premium Babyproducts

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>