LUVION Eco Fast Deluxe Bottle Warmer Instruction Manual

June 6, 2024
LUVION

LUVION Eco Fast Deluxe Bottle Warmer

PACKAGE CONTENTS

  • Bottle warmer
  • Steam cover
  • Bottle basket
  • Bottle ring
  • Sterilization base
  • Measuring cup
  • This Instruction manual

PRODUCT OVERVIEW

Bottle warmer (Fig. 1)
  1. Bottle warmer
  2. Time/Temperature display
  3. On/Off switch
  4. Mode settings button
  5. Time/Temperature increase button
  6. Time/Temperature decrease button
  7. Steam cover
  8. Bottle basket
  9. Bottle ring
  10. Sterilization base
  11. Measuring cup
INTRODUCTION

Thank you for purchasing the Luvion Eco Fast Deluxe bottle warmer. Make sure you always keep your original proof of purchase. For warranty cases you will always be asked to show a copy of your proof of purchase. For warranty claims you can contact the Luvion dealer or the local Luvion representative. More information can be found at www.luvion.com This manual contains all the information you need, to be able to use this Luvion Eco Fast Deluxe bottle warmer safely and with pleasure. Before using the bottle warmer, we recommend that you read this manual carefully. We ask for your extra attention for the safety instructions.

ATTENTION!

  • Always check the temperature of the food or milk before serving. This in order to ensure it has reached the feeding temperature;
  • Always place the basket in the chamber to heat up bottles or baby food;
  • It is advised to stir well to spread the heat evenly of the content in order to get the desired temperature;
  • The bottle should be placed in the bottle basket, with the ring slightly loosened;
  • Allow the bottle warmer to cool for approximately 15 minutes between uses. Never touch the inside of the chamber during or just after operation.
  • For safety reasons, this unit stops working automatically when the water dries off.
  • When heating bottles, it should be placed in the bottle basket. It should not be placed directly into the heating plate under the bottle.
  • Make sure to clean all included accessories before use.
IMPORTANT SAFETY PRECAUTIONS

Please note the following precautions before usage. Failure to comply may be dangerous.

  • Read all the instructions before using the product;
  • Place the bottle warmer on a flat and dry surface;
  • Never use the bottle warmer without water in it; change the water in the bottle warmer frequently for hygienic reasons;
  • Do not touch the hot surfaces;
  • This product is not a toy. Please keep the unit out of reach of children or with close supervision when this product is used near children;
  • Disconnect the bottle warmer from the power supply before adding water;
  • Always unplug the bottle warmer and remove the bottle from the product before feeding the baby;
  • Turn off the bottle warmer and disconnect from power supply after use;
  • Rinse the excessive water and wipe the bottle warmer with a soft cloth;
  • The appliance is for indoor use only;
  • Please do not expose this product to moisture or heat sources;
  • At the end of the product lifecycle, the bottle warmer should be brought to a collection point for the recycling of electrical and electronic equipment.

INSTRUCTION MANUAL

TO HEAT UP QUICKLY:
  1. Place the bottle basket (8) in the bottle warmer unit and place the bottle or jar (without lid) in the middle of the bottle basket (8). Depending on the size of the bottle, you could use the bottle ring (9) to help the small neck bottles fit.
  2. Fill the container of the bottle warmer with the below reference water content depending on the amount of milk or food in the bottle.
  3. Insert the plug into a 230Volts wall socket and turn on the bottle warmer (3).
  4. Press the mode settings button (4) and select the quick heating mode . The symbol flashes a few times before the heating element of the bottle warmer starts to work.
  5. The default heating up time is set to 3 minutes. Depending on the amount of milk or food, the timer can be adjusted by pressing on the buttons (5 and 6). The heat up function will start working after a few seconds.

The desired temperature of the milk/food is determined by the amount of water in the bottle warmer. For low temperature, it is recommended to use more water.
Note: the following chart can only be used as reference and is based on heating the milk/ food of 4°C to a temperature of 37°C. Depending on the initial temperature of the content of the milk/food, the room temperature, shape/size, material of the bottle or jar, as well as other conditioning factors, could cause the temperature range to vary. In this case, you may have to increase/decrease the warm-up time by pressing the buttons (5 & 6).
Note: For the glass jars, the heating time should be at least 30 seconds shorter than the heating time of plastic bottles.

AMOUNT OF MILK IN PLASTIC BOTTLE| AMOUNT OF WATER (ML) TO BE PUT IN THE BOTTLE WARMER| WORKING TIME
---|---|---
90ml| 35ml| 3 minutes
120ml| 35ml| 4 minutes
150ml| 40ml| 4 minutes
180ml| 40ml| 4 minutes
210ml| 40ml| 4 minutes
240ml| 40ml| 4 minutes
270ml| 50ml| 5 minutes
330ml| 50ml| 6 minutes
6. The display (2) starts to count down and when it reaches the 0:00, the bottle warmer will turn off automatically and 2 cycles of 2 beeps are emitted. 7. Remove the bottle/jar from the bottle warmer quickly when timer goes off and shake the milk or stir the food to ensure the heating is spread evenly. 8. Always check the temperature of your food or milk before serving with the inside of your wrist. When the temperature is too low after the heating cycle, briefly put the bottle into the bottle warmer unit and reheat it by adjusting the timer according to your preferences. When the temperature is too high, let it cool down for a while before serving the baby.

TO KEEP WARM:
  1. Place the bottle basket (8) in the bottle warmer unit and place the bottle or jar (without lid) in the middle of the bottle basket. Depending on the size of the bottle, you could use the bottle ring (9) to help the smaller bottles fit.
  2. Fill the container of the bottle warmer with the half amount of the bottle/jar content.
  3. Insert the plug into a 230Volts wall socket and turn on the bottle warmer (3).
  4. Press the mode settings button (4) and select keep warm mode. The symbol flashes a few times before it starts to work.

The default temperature is set to 37°C. Depending on the amount of milk or food, the temperature can be adjusted by pressing on the button to decrease the temperature (6) to 35°C. The adjustable temperature are from 35°C to 85°C

DISPLAY SYMBOL DESCRIPTION RANGE
Quick heating up mode, default time 3 minutes 1-16 minutes
Keeps warm, default temperature 37°C 35-85°C
TO DEFROST:
  1. Place the bottle basket (8) in the bottle warmer unit and place the bottle or jar (without lid) in the middle of the bottle basket. Depending on the size of the bottle, you could use the bottle ring (9) to help the small neck bottles fit.
  2. Fill the bottle warmer holder with enough water (at least half as much water as the content of the bottle or jar to be thawed, top up with water if necessary).
  3. Insert the plug into a 230Volts wall socket and turn on the bottle warmer (3).
  4. Press the mode settings button (4) and select keep warm mode function The symbol flashes a few times before it starts to work. (the keep warm mode and defrost mode are the same)
  5. The default temperature is set to 37°C. Decrease the temperature for thawing, by pressing on the decrease button, to 35°C (6).

Note: It is strongly recommended not to exceed the defrost function temperature above 35°C to prevent nutrient loss.

TO STERILIZE BOTTLE AND PACIFIERS:
  1. Place the sterilization base (10) to the bottom of the bottle warmer and put the inverted bottle without lid on top of the sterilization base. You can also place the pacifiers you’d like to sterilize in the bottle warmer.
  2. Pour 70ml water into the bottle warmer by using the measuring cup (11).
  3. Place the steam cover (7) on the bottle warmer to keep the heat inside and to prevent you from being hit by splashing hot water.
  4. Insert the plug into a 230Volts wall socket and turn on the bottle warmer (3).
  5. Press the mode settings button (4) and select the steaming mode function (the quick heating up mode and sterilization mode are the same). The symbol flashes a few times before the sterilize function starts to work.

The default steam sterilizer function is set to 3 minutes and 2 cycles of 2 beeps are emitted after the timer reaches the 0:00. Adjust the timer setting by pressing on the buttons (5 & 6) if you prefer to increase the time for sterilization. It is recommended to sterilize 8 minutes.

Attention! The steam cover gets very hot. Do not touch it during use. Wait a few minutes so that the steam cover can cool down before removing it. Use kitchen pliers (not included) to remove pacifiers from the bottle warmer.

MAINTENANCE INSTRUCTIONS :
  • Turn off the power supply before cleaning;
  • For hygienic reason, please empty the water out from the unit after use;
  • Clean the unit with a soft cloth or sponge, then dry it with clean cloth. If needed, use vinegar mixed with water to get rid of hard water deposits and rinse well afterwards;
  • Do not immerse the unit nor the powercord or plugs in water while cleaning;
  • Store the unit in a dry and cool environment

SPECIFICATIONS

Power supply: 220-240V – 50/60Hz
Power consumption: 500 WATTS
Heating time: 1-16 minutes
Temperature for keeping warm: 35-85°C

LUVION PREMIUM BABYPRODUCTS
Kleveringweg 7
2616 LZ Delft
The Netherlands
www.luvion.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals