MeTra 107-KI1HG Kia Seltos 2021 Up Dash Kit Installation Guide
- June 3, 2024
- Metra
Table of Contents
MeTra 107-KI1HG Kia Seltos 2021 Up Dash Kit
KIT FEATURES
- Designed specifically for ISO DDIN radios which have an “L” shaped chassis design, with the radio chassis at the bottom of the screen like the Alpine iLX-207. Also designed for Pioneer modular 6.8” radios like the DMH-C2550NEX and DMH-C2500NEX.
- Both textured and painted gloss black to match the factory finish.
KIT COMPONENTS
- A) Radio housing front
- B) Radio housing back
- C) Pioneer brackets
- D) panel clips (2)
- E) #8 x 3/8” Phillips screws (4)
WIRING & ANTENNA CONNECTIONS
Wiring Harness: Visit metraonline.com for audio/video and steering wheel control interface options. Antenna Adapter: 40-KI11
TOOLS REQUIRED
- Panel removal too
- Phillips screwdriver
Attention! Let the vehicle sit with the key out of the ignition for a few minutes before removing the factory radio. When testing the aftermarket equipment, ensure that all factory equipment is connected before cycling the key to ignition.
DASH DISASSEMBLY
-
Unclip and remove the trim panel behind the radio display. (Figure A)
-
Remove the (2) Phillips screws under trim panel removed in step 1. (Figure B)
-
Unclip and remove the small trim to the left of the instrument cluster. (Figure C)
-
Remove (1) Phillips screw from behind small trim panel removed in step 3. (Figure D)
-
Unclip and remove the entire trim surrounding the instrument cluster and including the a/c vents under the radio display. (Figure E)
-
Remove (1) Phillips screw securing the trim panel below the radio display which had the a/c vents in it then unclip and remove the panel. (Figure F, G)
-
Remove (2) Phillips screws securing the radio display and chassis. (Figure H)
-
Unclip unplug and remove the radio display and chassis.
KIT PREPARATION
Attach the two included panel clips to the radio housing back. (Figure A)
Bottom chassis DDIN radio provision
- Secure the radio into the radio housing back using screws supplied with the radio. (Figure A)
- Secure the radio housing front to the back using the supplied #8 screws. (Figure B)
- Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or Axxess. Test the radio for proper operation.
- Slide the radio assembly into to the dash, then secure using the factory screws.
- Reassemble the dash in reverse order of disassembly to complete the installation.
Pioneer modular DDIN radio provision
Note: For steps 1 and 2, reference the installation manual provided with the radio for which hardware to use. The display screen and radio chassis use two different types of screws.
- Secure the radio display to the Pioneer adapter brackets using (6) screws supplied with the radio. (Figure A)
- Connect the radio display/bracket assembly to the radio chassis using (4) screws supplied with the radio. (Figure B)
- Secure the radio assembly into the radio housing back using screws supplied with the radio. (Figure C)
- Secure the radio housing front to the back using the supplied #8 screws. (Figure D)
- Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or Axxess. Test the radio for proper operation.
- Slide the radio assembly into to the dash, then secure using the factory screws.
- Reassemble the dash in reverse order of disassembly to complete the installation.
Having difficulties? We’re here to help.
Contact our Tech Support line at:
386-257-1187
Or via email at:
techsupport@metra-autosound.com
Tech Support Hours (Eastern Standard Time)
Monday – Friday: 9:00 AM – 7:00 PM
Saturday: 10:00 AM – 7:00 PM
Sunday: 10:00 AM – 4:00 PM