EDIFIER W820NB Plus Wireless Noise Cancellation Over-Ear Headphones User Manual
- June 3, 2024
- Edifier
Table of Contents
W820NB Plus Wireless Noise
Cancellation Over-Ear Headphones
User Manual
W820NB Plus Wireless Noise Cancellation Over-Ear Headphones
Power ON/OFF
- Power ON: press and hold the ” ” key for about 3s when powered OFF until the LED blinks blue.
- Power OFF: press and hold the “ ” key for about 3s when powered ON until the LED blinks red.
Note:
If there is no Bluetooth connection for 5 minutes after power on, the
headphones will turn off automatically; if there is no Bluetooth connection
under noise cancellation mode, the headphones will turn off automatically
after 4 hours.
Pairing
Pairing for the first time
- Press and hold the “ ” key for about 3s when powered off. Blue and green LED will blink alternately and rapidly.
- Select “EDIFIER W820NB Plus” in your device setting to connect. Blue LED will blink twice after connected. Note:
For subsequent use, the headphones will automatically connect to the device used last time.
Pairing for new device
- Press and hold the “ ” key for about 6s when powered off to skip the latest connected device and pair the new Bluetooth device. Blue and green LED will blink alternately and rapidly.
- Select “EDIFIER W820NB Plus” in your device setting to connect. Blue LED will blink twice after connected.
Reset
Simultaneously press and hold the “+” ” -” keys for about 5s when powered on to clear pairing records. Blue LED will blink 6 times rapidly when successful.
Charging
- Connect the small end of the included USB cable to the USB-C port of the headphones and connect the other end to a USB-A power supply or wall charger(not included).
- Orange LED is steady lit when charging and off when fully charged. Note:
Please do not charge the headphones when there is sweat or other liquids inside the charging port, which may damage the headphones.
Input: 5V 1A
Connecting to PC as wired headphones
- Connect the small end of the included USB cable to the USB-C port of the headphones and connect the other end to the USB-A port of the PC.You can listen to music, talk and charge the headphones after the connection is successful.
- Orange LED is steady lit when charging and green LED is steady lit when fully charged.
Note:
It is recommended to use the included USB cable, and other cables may have
compatibility issues that prevent them from working properly.
Controls
Note:
- —: Press and hold.
- Default sound control: noise cancellation & ambient sound.
- Images are for illustrative purposes only and may differ from the actual product.
- Download Edifier Connect App for more customizable control settings.
Scan and download Edifier Connect App
FCC statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
IC statement:CAN ICES-003(B) / NMB-003(B).
FCC ID: Z9G-EDF200
IC:10004A-EDF200
210-200927
Input: 5V 1A
Hereby, Edifier International Limited declares that the radio equipment type
EDF200118 is in compliance with Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the following internet address:
https://www.edifier.com/int/eu-doc.html
Declaration for EU
Frequency Band: 2400Mhz-2483.5Mhz
There is no restriction of use.
Specific Absorption Rate (SAR) information:
This (Edifier International Limited) meets the government’s requirements for
exposure to radio waves. The guidelines are based on standards that were
developed by independent scientific organizations through periodic and
thorough evaluation of scientific studies.
The standards include a substantial safety margin designed to assure the
safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement
The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue.
Device types: (EDF200118) (FCC ID: Z9G-EDF200) has also been tested against
this SAR limit. The highest SAR value reported under this standard during
product certification when properly worn on the body is 0.046W/kg.
This device was tested for typical body-worn operations with the back of the
handset kept 0mm from the body. To maintain compliance with FCC RF exposure
requirements, use accessories that maintain a 0mm separation distance between
the user’s body and the back of the handset. The use of belt clips, holsters
and similar accessories should not contain metallic components in its
assembly. The use of accessories that do not satisfy these requirements may
not comply with FCC RF exposure requirements, and should be avoided.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF
exposure requirements, a minimum separation distance of 0mm must be maintained
between the user’s body and the handset, including the antenna.
Third-party belt-clips, holsters, and similar accessories used by this device
should not contain any metallic components. Bodyworn accessories that do not
meet these requirements may not comply with RF exposure requirements and
should be avoided. Use only the supplied or an approved antenna.
For more information, please visit our website:www.edifier.com
Model: EDF200118
Edifier International Limited
P.O. Box 6264
General Post Office
Hong Kong
www.edifier.com
2022 Edifier International Limited. All rights reserved.
Printed in China
NOTICE:
For the need of technical improvement and system upgrade, information
contained herein may be subject to change from time to time without prior
notice.
Products of EDIFIER will be customized for different applications.
Pictures and illustrations shown on this manual may be slightly different from
actual product.
If any difference is found, the actual product prevails.
IB-200-W820NP-00 V1.0
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>