LAMINAM UTS-1 Invisible Wireless Charger User Guide
- June 13, 2024
- LAMINAM
Table of Contents
UTS-1 INVISIBLE WIRELESS CHARGER
COMPATIBLE FOR USE WITH
Quick Start Guide
Setup and Installation on Laminam Surfaces
Developed & manufactured by:
Quick start guide
Kew Lab UTS-1 Invisible Wireless Charger – THIN
Kew Labs UTS -1 Invisible wireless chargers are designed to be installed
under nonmetallic materials to turn any surface into a hidden wireless phone
charger.
UTS-1 Invisible Wireless Charger – Thin (SKU: UTS-1T) has been tested and
approved for use on Laminam® surfaces.
Product Features:
- Hidden phone charging keeps surfaces tidy.
- 8-12mm (0.31”-0.47”) long distance charging capability
- Apple® and Samsung® fast charge protocols
- Patented Intelligent Power Communication® (IPC®) Technology.
- Daisy chain two chargers with 1 adapter (SKU: UTS-1TDC)
Recommended Usage:
- Kitchen countertops
- Kitchen Islands
- Furniture and bar tops
Installation Thickness Guidelines
Laminam
Surface (mm)| Main
Application| Compatibility| Routing
Requirement| Charger
Setting
---|---|---|---|---
12+| Countertops
&
Furniture| Yes| No| H
20+| Yes| Route to 12 mml| H
See Laminam’s Technical Guide for Fabricators for technical information about routing the 20mm slab.
Specifications
| Item | UTS-1 – THIN Specifications |
|---|---|
| Product SKU & Variations | |
| SKU | Name |
| UTS-1T | UTS-1 Wireless Charger – |
| Thin Version | THIN |
| UTS-1TDC | UTS-1 Daisy Chain |
Wireless Charger – Thin
Version| THIN
Input Power| DC 12V/3A (DC12V/5A for daisy chain adapter)| Output Power: Max
20W
Charging| Apple 7.5W, Samsung 10W, Standard SW Qi wireless charging
Material Compatibility| Laminam
Devices Compatibility| All Qi wireless charging enabled devices
Unit Size / Weight| 18.2cm (L) x 11.2 cm (W) x 2.0 cm(H) / 208g (charger unit)
7.165″ (L) x 4.4″ (W) x 0.787″ (H) / 7.34 oz (charger unit)
Effective
charging distance| 8mm – 12mm (0.31″ – 0.47″)
Accessories Included| Multi design charging position sticker, calibration
templates, power adapter 12V/3A/5A, cable management clips, screws, double
sided tape (pre-fixed)
Fixing Method| Preinstalled 3M VHB double sided tape or screws (provided)
Certifications| Charger: FCC, IC, CE, KC, RoHs| Adapter : CE, UL, RoHs, JP,
GS, KC
(See www.kewlabstech.com/uts-1install for full product and adapter specs)
Laminam 12mm – Kitchen Installation Example
-
Cut hole in island carcass – ensure the opening is big enough to be able to remove charger if needed
-
Ensure power is available to charger either in the island or cupboard.
-
Mount charger using tape provided and plug in
-
Calibrate or measure to center coil position to place charging indicator sticker
-
Set charger switch position according to thickness (H setting for 12mm)
-
Place center of phone on center of sticker
Design Tips and Guidelines
Aligning the charging position – Use phone indicator on charger as center
charging position.
Design Tips
- Ventilation Allowances – Wireless charging naturally produces a small amount of heat in both phone and charger. Do not direct cover UTS-1 vent and leave at least 5cm (2”) clearance.
- Heat Proximity – UTS-1 should not be located within 20cm (8”) of a heat source such as hobs.
- Cut-outs proximity – UTS-1 charger and milling must not be located within 15mm (6”) of a cut out or another milling.
- Water Protection – UTS-1 is not waterproof so should be located with adequate protection or distance from water sources like sinks.
- High temperatures – high environmental/room temperature affects wireless charging performance – avoid mobile phones charging in direct sunlight or temperatures exceeding 30c (86f).
Installation and setup help:
- Ensure charger is set to correct setting in ‘installation thickness table’
- Phone placement tip – Align center of phone with charging indicator.
- Re-connecting your phone – It can take 2-3 seconds for a phone to connect once placed on the charger. Do not immediately move the phone if it does not connect when placed down.
Download full installation instructions and technical drawing: www.kewlabstech.com/uts-1install
For project, purchasing and installation enquiries: Please email info@kewlabstech.com
Dealer portal registration: www.kewlasbtech.com/register
For product support and aftercare: Please email support@kewlabstech.com
DISCLAIMERS:
- The equipment UTS-1 Invisible Wireless Charger is developed and manufactured by and any liabilities and warranties related to the equipment is on sole responsibility of the manufacturer.
- Any electrical installation should be done following local codes and regulations. Laminam shaw not be held liable for any damages, losses or injuries associated with the installation and/or use of the UTS-1 Invisible Wireless Charger with LAMINAM Surfaces.
- LAMINAM® is not affiliated in any way with Kew Labs.
Kew Labs
29000 Aurora Road
Solon, Ohio, 44139, USA
www.kewlabstech.com
References
- High-Power Wireless Charger for Sale | Kew Labs Tech
- UTS-1 Wireless Charger Installation Guide - Kew Labs
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>