KOSUMOSU ACD210C Digital LED Clock Neon Light User Manual

Table of Contents

Thanks for choosing our product, Please read the user manual carefully before using the LED clock

Time/Date/Year setting

Press the “CLOCK” button to enter the time setting, and the Hour numbers start to flash, then press the or button to adjust the hour, after that press the button and skip to set the minutes.
Adjust the minutes via the or button, finally, press the “CLOCK” button to confirm the time setting and skip to the Date setting.
Then adjust the month and day numbers via these 4 arrow buttons as above, and press the “CLOCK” button to confirm the date setting and skip to the Year setting.
Adjust the Year numbers via the or button, finally press the “CLOCK” button to confirm the setting and back to time mode.

12/24 Hours System

Seconds flashing

Press the button to turn on/off the two flashing second points between the hours and minutes.

Alarm setting

Press the “ALARM” button twice to enter the Alarm setting, press or button to switch the Hour or Minute setting, and then adjust the datas via or the buttons.
Press the “ALARM” button to confirm the alarm time.
Press the button to set the alarm clock “ON” or “OFF”.
Finally, press the “ALARM” button to confirm and back to clock mode.

In clock mode, press the “ALARM” button, and it’ll show the preset alarm time, or if the alarm was turned off, it’ll show “OFF”.

Snooze

This LED clock has a preset Snooze function, which means the bell will ring 3 times at 5-minute intervals, and 1 minute per ring.
When the bell rings, you can press the “ALARM” button to pause ringing and delay the alarm for 5 minutes.
When the bell rings, you may press any button besides the “ALARM” button to stop ringing right away.
If you want to close the alarm entirely, please set the alarm OFF as above Alarm Setting descriptions.

Brightness setting (Brightness Dimming)

Press the “BRIGHT” button to switch the brightness dimming in sequence for ” High – Medium- Low – Auto”.
There are 8 levels of automatic brightness dimming available, which adjust automatically based on the ambient light via the built-in light sensor.
Press the “LED Display on/off ” button 9 to turn on or off the LED light. It is NOT equivalent to shutting down the clock!)
Brightness dimming can ONLY be adjusted for solid color light mode, not for Gradient Color Light or Neon Light modes.

Temperature display

Press the “TEMP” button to show the Temperature in °C for 5 seconds., or press it again to show it in F for 5 secs., then back to clock mode automatically.

Loop display

Press the button to turn on/off the Loop Display of the “Time”, “Temperature” and “Date”.
Gradient Color: press the “ button on the remote control to set the gradient color LED light, which will start gradual changes cyclically for red → orange → yellow →green → blue → Purple → Pink.
Colorful Neon Light: press the button again to set it for the colorful neon light.
In short, you can press the button to set the gradient color LED light and colorful neon light in turns.
Press the “USER” button to make the gradient color or neon color stand still as your custom light color.

Hang on the wall (desk clock/wall clock)

Time/Date/Year setting

Press the “SET” key to enter the time setting.
Press the “SET” key again to switch between hours, minutes, months, days, and years, and adjust these datas via “+” or key, then press the “SET” key to confirm the setting.

In clock mode, long press the “SET” key for 3 seconds. to enter into the alarm setting, the HOUR numbers will flash.
Adjust the Hour via the “+”/ “-“ key, then press the “SET” key and skip to the minute numbers, to set via the “+”/- key.
Press the “SET” key to confirm the alarm time, then press the “key to turn ON or OFF the alarm clock.
Finally, press the “SET” button to confirm the alarm setting and back to clock mode.

In clock mode, press the “+” key, and it will show the alarm time, or if the alarm was turned off, it will show “OFF”.

In clock mode, long press the “+” key for 3 seconds. to turn on/off the two flashing second points in the middle.
Long press the “+” key for 6 seconds. on the back of the clock to turn on/off the Loop Display of “Time”, “Temperature” and “Date”.
Press the – key to show the Temperature in C for 5 secs., or press it again to show it in F for 5 secs., then back to clock mode automatically.
In clock mode, long press the – key for 3 seconds. to set the brightness dimming in sequence for ” High – Medium – Low – Auto.

Digital Led clock x 1
Base bracket x 1
Plug in USB cable x 1
AC adapter is not included
Remote control x 1
Installation kit x 1
Any problem, please support@sz-krs.com.cn. with the order number and detailed problem