EATON CWGE-00-01 Water Guard Instruction Manual
- June 3, 2024
- EATON
Table of Contents
EATON CWGE-00-01 Water Guard
Overview
What’s In The Box
Device/Type/Color
- CWGE-0U/31 Universal Pure white, gloss
- CWGZ-CM/03 Cover main Silver, matt
- CWGZ-CM/09 Cover main Jet black, matt
- CWGZ-CS/03 Cover sensor Silver, matt
- CWGZ-CS/09 Cover sensor Jet black, matt
Technical Data
- Power supply 230 VAC +10% -15%, 50 Hz
- Solenoid Valve Support
- Power supply 230 VAC, 50 Hz max. 100 W
- Type NO and NC
- On-device settings
- Valve Type NO (default), NC
- LED Multi-Color operation status
- Dimensions 70 x 70 x 39 mm (L x W x D)
- RF 868.3 MHz (xComfort compatible)
- Max RF power: 25 mW (ERP)
- Cable strain relief
- Cable diameter Ø 4.5 -7 mm
- Cable type H05VV-F
- Screw torque 0.5 Nm
- Important! Always use, included, isolation tubes on the cable when using the strain relief
- Cover screw torque 0.1 Nm
Mounting
Solenoid Valve not included
55x55mm Frame compatibility
Eaton| Merten| Gira| **Busch &Jäger*| Jung|
Berker| Siemens| Elko| Kopp**
---|---|---|---|---|---|---|---|---
Standard| 1-M| Standard 55| Carat| AS| S.1| Delta line| RS16| Alaska
| Atelier M| E2| Solo| A 500| B.1| Delta vita| Plus|
| M-Smart| Event| Future| A Plus| B.3| Delta miro| |
| M-Arc| Esprit| Future Linear| A creation| B.7 Glas| Delta miro Glas| |
| M-Star| E22| CZ Future| | | | |
| M-Plan| | Busch-balance SI| | | | |
| M-Plan II| | | | | | |
| M-Plan Metall| | | | | | |
Danfos EV series (NO types)
Wiring
On wall wiring
In wall wiring
Wiring diagram
Connect sensor cable
How to apply the sensor cable
- Surface must be clean, dry and dust-free
- Do not to touch the exposed adhesive area at any time
- Press fi rmly
- Once mounted, the adhesive tape cannot be reused
Remove sensor cable
Basic mode
Connect the Push-button or Water Detector
Remove the Push-button or Water Detector
Configure Valve type
Back to factory default
LED during operation
No RF communication
Over temperature protection. Check load
Quick User Guide
What to do if water is detected:
Declaration of conformity of the installation
The xComfort Water Guard has been installed according to the instruction manual and tested before use by:
- Name electrician: ………………………………………………………………………………..
- Company: …………………………………………………………………………………
- Telephone: …………………………………………………………………………………
- E-mail: …………………………………………………………………………………
- Customer name: …………………………………………………………………………………
- Customer address: ……………………………………………………………………………….
Installation:
- xComfort Water Guard – Controller in: …………………………………………………………
- xComfort Water Guard – Detector 1 in: …………………………………………………………
- xComfort Water Guard – Detector 2 in: …………………………………………………………
- xComfort Water Guard – Detector 3 in: …………………………………………………………
- xComfort Water Guard – Detector 4 in: …………………………………………………………
- xComfort Water Guard – Detector 5 in: …………………………………………………………
- Signature electrician: ……………………………………………………
- Date: ……………………………………………………
Declaration of Conformity
We, EATON Industries (Austria) GmbH 3943 Schrems, Eugenia 1 Austria
declare under our sole responsibility as a manufacturer that the product (family)
Eaton – Water Guard UP
CWGE-00/01
(the declaration of conformity applies to all listed types within our actual product catalogue) provided that it is installed, maintained, and used in the application intended for, with respect to the relevant manufacturer’s instructions, installation standards, and “good engineering practices”
complies with the provisions of Council directive(s):
- RED Directive 2014/53/EU
- RoHS Directive 2011/65/EU + 2015/863
based on compliance with the following standard(s):
EN 300220-2 V3.2.1, EN 301 489-1 V2.2.3, EN 301489-3 V2.1.1, EN
IEC 63044-5-1:2019, EN IEC 63044-5-2:2019, EN IEC 63044-5-
3:2019, EN 60669-2-5:2016, EN 63000:2018.
Eaton Industries (Austria) GmbH, Eugenia 1, 3943 Schrems, Austria
© 2021 by Eaton Industries (Austria) GmbH, www.eaton.eu/documentation. www.eaton.com/recycling.
All Rights Reserved / Printed in Austria.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>