EATON N052-024 Patch Panels User Guide
- May 15, 2024
- EATON
Table of Contents
EATON N052-024 Patch Panels
Specifications
-
Model Numbers: N052-024, N052-P24, N052-048, N252-024,
N252-024-6A, N252-024-6A-OF, N252-P24, N252-P24-WH, N252-048 -
Compatibility: Cat5/5e/6/6a 110-Type UTP
-
Wire Gauge: 22-24 AWG
Installation
-
Strip the cable jacket approximately 1.25 in. (30 mm).
-
Seat each wire according to the wiring scheme shown in Figure
1. Ensure the untwisted length is as short as possible. Avoid overlapping one pair over the others. -
Use a 110 impact tool for termination.
-
In order to maintain stable performance, ensure the cable bundles are secured with the attached straps.
Warranty
Eaton follows a policy of continuous improvement. Specifications are subject
to change without notice.
Eaton
1000 Eaton Boulevard Cleveland, OH 44122 United States
Eaton.com
Eaton is a registered trademark. All trademarks are property of their
respective owners.
FAQ :
Q: What wire gauge is compatible with these patch panels?
A: The patch panels are compatible with 22-24 AWG wire.
Quick Start Guide
Patch Panels
- N052-024
- N052-P24
- N052-048
- N252-024
- N252-024-6A
- N252-024-6A-OF
- N252-P24
- N252-P24-WH
- N252-048
Purchased product may differ from image.
Installation
-
Strip the cable jacket approximately 1.25 in. (30 mm).
-
Seat each wire according to the wiring scheme shown in Figure 1. Ensure the untwisted length is as short as possible. Avoid overlapping one pair over the others.
Note: 110 punchdown orientation may vary by model.
-
Use a 110 impact tool for termination.
Note: Set the tool to the “Low Impact” setting.
-
In order to maintain stable performance, ensure the cable bundles are secured with the attached straps.
Warranty
LIFETIME LIMITED WARRANTY
We warrant our products to be free from defects in materials and workmanship for its lifetime. Our obligation under this warranty is limited to repairing or replacing (at its sole option) any such defective products. Visit Tripplite.Eaton.com/support/product- returns before sending any equipment back for repair. This warranty does not apply to equipment which has been damaged by accident, negligence or misapplication or has been altered or modified in any way.
EXCEPT AS PROVIDED HEREIN, WE MAKE NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Some states do not permit limitation or exclusion of implied warranties;
therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the
purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL WE BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS
PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, we
are not liable for any costs, such as lost profits or revenue, loss of
equipment, loss of use of equipment, loss of software, loss of data, costs of
substitutes, claims by third parties, or otherwise.
WEEE Compliance Information for Customers and Recyclers (European Union)
Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations, when customers buy new electrical and electronic equipment from Eaton, they are entitled to:
- Send old equipment for recycling on a one-for-one, like-for-like basis (this varies depending on the country)
- Send the new equipment back for recycling when this ultimately becomes waste
Eaton has a policy of continuous improvement. Specifications are subject to change without notice.
- Eaton
- 1000 Eaton Boulevard
- Cleveland, OH 44122
- United States
- Eaton.com
- © 2023 Eaton
- All Rights Reserved
Publication No. 23-11-178 / 93-3182_RevD November 2023
Eaton is a registered trademark.
All trademarks are property of their respective owners.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>