VICTOR VWRP-3200 5 In 1 Turntable Music Center Instruction Manual

June 4, 2024
VICTOR

VICTOR VWRP-3200 5 In 1 Turntable Music Center

VICTOR VWRP-3200 5 In 1
Turntable Music Center productSafety instructions

WARNING

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

DANGEROUS VOLTAGE: The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product`s enclosure that may be of suffcient magnitude to constitute a risk of electric shock to persons.
ATTENTION: The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING: Invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to laser beam.
This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth.

Important Safety Instructions

  1. Read these instructions – All the safety and operating instructions should be read before this product is operated.
  2. Keep these instructions – The safety and operating instructions should be retained for future reference.
  3. Heed all warnings – All warnings on the appliance and in the operating instructions should be adhered to.
  4. Follow all instructions – All operating and use instructions should be followed.
  5. Do not use this apparatus near water – The appliance should not be used near water or moisture – for example, in a wet basement or near a swimming pool, and the like.
  6. Clean only with a dry cloth.
  7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
  8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
  9. Protect the power cord from being walked on or pinched particularly at the plugs, power outlets, and at the point where they exit from the apparatus.
  10. Only use attachments/accessories specified by the manufacturer.
  11. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
  12. Unplug the apparatus during lighting storms or when unused for long periods of time.
  13. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
  14. The mains plug is used as disconnect device, the disconnect device shall remain readily operable.
  15. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall not be placed on apparatus.
  16. The use of the equipment in moderate climate.
  17. The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, tablecloths, curtains, etc.
  18. Do not place open flame sources, such as lighted candles, on the apparatus.
  19. The symbol with indicates AC voltage.
  20. CAUTION: The se servicing instructions are for use by qualified service personnel only.
    To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

FEATURES

VICTOR 5-in-1 Record Player features Chair Height legs in a fun Retro Style. The built in 3-Speed Turntable & FM Radio are ready to play all your favorite songs! The Dual Bluetooth feature allows streaming of your vinyl records to an external Bluetooth Speaker or plays music from your Smart Device through the Andover’s built in Speakers. The 3.5mm Aux Input & RCA Audio Outputs allow for even more additional Playback options. Can also be used on a Tabletop as base height feet are also included.

  • 3-speed record player will play 33 1/3, 45, 78 rpm records
  • Bluetooth In connectivity allows you to stream music from another source up to 33 feet away.
  •  Bluetooth Out Connectivity allows you to stream vinyl playback through any external Bluetooth Speaker
  • FM Radio
  • Includes a 3.5mm Aux Input, Headphone Jack, & RCA Output for additional connectivity option
  • Includes Chair Height & Counter Top Legs
  • Built in Stereo Speakers for playback convenience

SPECIFICATIONS

Product Name Andover (5-in-1 Turntable Music Center)
Turntable Speeds (RPM) 33 1/3, 45, 78
FM Frequency Range 87.5 – 108MHz
Bluetooth Version V5.1
Bluetooth Transmission Distance Up to 33 feet (10 Meters)*
Rated Frequency 2.4GHz
Input Aux In
Output Line Out, Headphone x1
Built-in Speakers 3” x 2
Speaker Power Output 3W x 2
Power Source AC/DC 100-240V 5.8V/1.5A
Accessories Included 45 RPM Adaptor, Aux In Cable, ETL Approved

Power Adaptor, User Manual, Quick Set Up Guide

*Distance may vary depending on any objects or interference between devices.

PRODUCT OVERVIEW

Turntable Features

  1. Turntable Platter
  2. Turntable Spindle
  3. 45 RPM Adapter
  4. Cue Lever
  5. Hold Down Clip
  6. Speed Selector
  7. Tonearm
  8. Cartridge

Front Control Panel

  1. Headphone Jack
  2. AUX IN Jack
  3. Power Indicator
  4. Function Knob
  5. Bluetooth Indicator
  6. FM Dial
  7. Volume +/- Tuner Bluetooth® Out

Back Control Panel

  1. DC IN Jack
  2. LINE OUT Jacks
  3. FM Antenna

SETUP & BASIC OPERATION

In the Box:

  • 1 x Turntable
  • 1 x Power adapter
  • 1 x 45 RPM adapter
  • 1 x Aux In cable
  • 1 x User manual
  • 4 x Legs (upper long leg + lower long leg)
  • 16 x Screws (for machine feet installation)

Please contact Customer Service immediately the if there are any missing parts or accessories from the package or the product is damaged. Retain the original packaging materials for exchange or return purposes.

Read this user manual before any operation
All the warnings and safety instructions should be followed for your safety. Any improper operation not included in this manual may cause injuries or damage the product.
Note: All the images and pictures in this manual are for illustration purposes only and may be slightly different from the actual appearance of the product.

Install the Legs (If Applicable)

  1. Assemble each leg by twisting the top part of the leg onto the bottom part of the leg.
  2. Place the unit on a flat, smooth surface, with its bottom upwards. Be careful the cover stays closed.
  3. Align the holes on the leg joints to the holes on bottom of the unit.
  4. Use a Phillips screwdriver and screws to secure the legs to the bottom of the unit.
  5. Turn over the unit when finished. Make sure it stands firmly on an even surface.

Power Connection

  1. Use the power adapter in the box to connect the unit to a nearby power outlet.
  2. Plug the small end of the adapter into the DC IN Jack on the back of the unit.
  3. Insert the metal prongs on the big end of the adapter into a wall outlet.

Note: Only use the power adaptor provided with the unit. Note: Only use the power adaptor provided with the unit.

LISTENING TO A RECORD

  1. Unfasten the clasps on both sides of the main unit to open the cover.
  2. Detach the white stylus protector by pressing both sides and pulling straight off the stylus.
  3. Set the Function Tuner to “PHONO” position. The Power Indicator will turn on in red.
  4. Place a vinyl record on the turntable. Align the turntable spindle to the hole on the record. Note: Place the 45 RPM adapter on the turntable spindle first if playing a 45 RPM record.
  5. Slide the Speed Selector to 33, 45 or 78 to match the play speed of the record.
  6. Unlock the Hold Down Clip.
  7. Raise the Cue Lever to lift the Tone arm off the Tone arm support.
  8. Gently move the Tone arm to the edge of the record (or the starting point of a track).
  9. Release the Cue Lever to put the Tonearm onto the record; and the turntable will begin playback.
  10. Turn the VOLUME +/- Tuner to adjust the volume.
  11. To pause/stop during playback, raise the Cue Lever to lift the Tonearm off the record.
  12. When finished listening:
    • Lift the Tonearm off the record by raising the Cue Lever.
    • Put the Tonearm to its support by hand,
    • Release the Tonearm by putting down the Cue Lever.
    • Lock the Hold Down Clip.

Note: After you play 78 RPM vinyl record, it will stop in about 60 seconds.

CONNECTING TO BLUETOOTH

Under this mode you can play music from an external device via Bluetooth.

  1. Set the Function Tuner to “BT” position, and the Bluetooth® Indicator starts to flash.
  2. On your external audio player, pair with the “VICTOR VWRP-3200” Bluetooth® device.
  3. When the Bluetooth® connection is established, you will hear a short confirmation sound from the unit, and the Bluetooth® Indicator will turn to solid blue.

Listen to Music on Bluetooth® Devices (Speakers, Headphones, etc.)

  1. Disable the Bluetooth® function on all devices nearby.
  2. Play a vinyl record on the unit as described above.
  3. Press the Volume Tuner/Bluetooth Out to the turn on the Bluetooth transmitter feature. The Bluetooth Indicator will start flash in orange.
  4. Power on your listening device (speakers, earbuds, etc.) and activate its Bluetooth function.
  5. Your turntable will automatically connect to your listening device and the flashing Bluetooth Indicator will show breathing effect.
  6. Adjust the volume on your listening device and begin to enjoy music.

Note:

  • Besides turntable mode, the Bluetooth out feature can also be activated in AUX and FM mode.
  • Besides TWS earbuds, you can also connect other audio listening devices through Bluetooth (e.g. wireless headphone, soundbar, amplifier)

CONNECTING TO AUX DEVICE

You can play audio from an external stereo system or audio device on the unit with the AUX IN mode.

  1. Insert one end of the 3.5mm AUX cable into the AUX IN Jack on the unit.
  2. Insert the other end of the 3.5mm AUX cable into your stereo system or device.
  3. Set the Function Tuner to AUX position. The Power Indicator will turn red.
  4. Start to play your favorite music on your external stereo system or audio device.

USING THE FM RADIO

  1. Set the Function Tuner to FM position. The Power Indicator will turn red.
  2. Extend the FM Antenna on the back of the unit to strengthen the signal receiving ability. You can also connect the unit to an outdoor antenna if necessary.
  3. Rotate the FM Tuner to search your favorite FM radio station.
  4. Adjust the volume by switching the VOLUME +/- Tuner.

CARE & MAINTENANCE

General Care

  • When unplugging the power plug, always pull directly on the plug. Never pull the cord.
  • To keep the laser pickup clean, do not touch it, and do not forget to close the disc tray.
  • Do not attempt to clean the unit with chemical solvents. Use a clean, soft, dry cloth.
  • Be sure to unplug the unit if you will not intend to use it for an extended period of time.

How to Replace the Turntable Stylus
The stylus should last about 50 hours under normal use. However, it is recommended that the stylus be replaced as soon as you notice a change in sound quality. Prolonged use of a worn-out stylus may damage the record. The higher speed of 78 RPM records wear out the stylus more quickly.

Remove the Old Stylus

  1. Hold the turntable cartridge firmly with one hand as illustrated in Fig. A.
  2. Push down the front edge of the stylus use other hand as illustrated in Fig. B.
  3. Rotate the stylus as illustrated in Fig. C.
  4. Rotate the stylus down and outward as illustrated in Fig. D.VICTOR VWRP-3200 5 In 1 Turntable Music Center fig 14

Install the New Stylus

  1. Hold both sides of the stylus and place the back of the stylus on the tip of the cartridge.
  2. Rotate the stylus up and inward until it is flush with the cartridge.
  3. Push the stylus tip towards the cartridge until you hear a click.VICTOR VWRP-3200 5 In 1 Turntable Music Center fig 15

How to Maintain Vinyl Records
Too prolong the life of your vinyl records, following the handling, cleaning, and storing tips below.

Handling

  • Skin oils can gradually deteriorate the quality of your record. Do not touch the record’s grooves. Only handle records by the edges or its center. Make sure your hands are clean when handling a record.
  • Static will deteriorate the sound quality and collect dust. Brush the record with an anti-static brush before and after playing.
  • When checking the record, never use a UV light or direct sunlight, an LED light is recommended if needed.

Cleaning

  • If you find any dust, finger marks or other residue on the record surface, gently wipe the surface in a circular motion with a dry soft anti-static lint-free cloth or brush.

Storing

  • To avoid dust and scratches, Keep records in their sleeves, jackets, or vinyl record crate when not in use.
  • Store records in a clean, cool, dry, static-free and UV-free environment.
  • Store records vertically, not horizontally, to prevent them crushing one another.
  • Do not store your records in the trunk of your car. The temperature in a closed trunk can ruin your collection.

TROUBLESHOOTING GUIDE

If you experience any issues with the unit, please review the possible solutions below before returning or calling for maintenance.

Symptom Possible Cause(s) Solution(s)

Power

No power (Power Indicator is off)

| Adapter had not been connected or

connected incorrectly

| Use the original adapter to connect the unit to wall outlet as instructed in the manual.
The unit is not switched on.| Switch the unit on.
Power outage| Wait the power supply back to normal or use other AC power supply.
Turntable mode
Noise or sound

distorted

| Speed Selector set incorrectly| Set the Speed Selector to the same speed as the RPM of the record.
The stylus is worn| Replace the stylus with a new one.
AUX in mode

No sound

| The external play is connected incorrectly or malfunctioning.| Connect the external audio player as described in this manual. Ensure the audio player works correctly when not connected to the unit.
The Aux in cable is plugged in the wrong jack(s).| Connect one end of the Aux in cable to Headphone jack, AUX out jack or Line out jack of the player, the other end to the AUX IN jack on the unit.

Change with another Aux in cable if necessary.

The unit is not turned on or the volume is set to minimum.| Turn on the unit and set the volume to high.

Low sound

| The volume of the connected player or/and the turntable is set to low.| Set the volume to high.
Bluetooth mode
Bluetooth not

functioning

| The playback mode is set incorrectly| Turn the Function Knob to “BT“ position.
The Bluetooth connection fails.| Connect the player to the unit as indicated in the manual.
FM mode

Noise or sound distorted

| Station not tuned properly.| Tune the radio station to a proper position.
Bad radio reception.| Extend the FM antenna to different positions or connect the antenna to Outdoor antenna system to improve the radio reception.
Bluetooth transmitter mode

No Sound

| The unit is not powered on or not in the proper mode.| Turn on the unit and set to Bluetooth Transmitter mode.
Bluetooth connection fails.| Connect the unit to the listening device as instructed in the manual.
The connected player does not work| Ensure the listening device works correctly when not connected to the unit.

FCC NOTICE

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

WARNING: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
The device must not be colocated or operating in conjunction with any other antenna or transmitter.
To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20cm from nearby persons.

IC STATEMENT

This device complies with RSS247 of Industry Canada. Cet appareil se conforme à RSS247 de Canada d’Industrie. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. appareils radio exempts de licence.
Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prejudiciable, et (2) ce dispositif doit accepter tout brouillage recu, y compris un brouillage susceptible de provoquer un fonctionnement indesirable.

The device must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with IC radiation exposure limits set forth for an uncontrolled environment.
The device should be installed and operated with a minimum distance of 20cm between the radiator and your body.

CAUTION ON MODIFICATIONS

Any changes or modifications not expressly approved by the grantee of this device may void the authority granted by the FCC to operate this equipment. Electric and electronic equipment contains materials, components and substances that can be hazardous to your health and the environment, if the waste material (discarded electric and electronic equipment) is not handled correctly. Electric and electronic equipment is marked with the crossed-out trash can symbol, seen the right side. This symbol signifies that electric and electronic equipment should not be disposed of with other household waste but should be disposed of separately. All cities have established collection points, where electric and electronic equipment can either be submitted free of charge at recycling stations and other collection sites or be collected from the households. Additional information is available at the technical department of your city.

SUPPORT

We do our best to offer high quality products to our customers. If you experience any issues or problems with your product, please contact customer support as many issues can be quickly resolved.
If you have problems with your device, please consult the instructions in this manual. Please also visit us on the web at www.naxa.com to get up to the minute news, alerts, and documentation for your device. For additional assistance, please contact Naxa Technical Support.
Naxa Technical Support
2320 East 49th St.
Vernon, CA 90058
866-411-6292
http://www.naxa.com/supportcenter
*This product has been manufactured and sold under the responsibility of NAXA ELECTRONICS INC.
VICTOR and the DOG & GRAMOPHONE logo are trademarks used under license by NAXA ELECTRONICS INC.
Further information at www.victor-brand.com.
All other products, services, companies, trademarks, trade or product names and logos referenced herein are the property of their respective owners

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals