VICTOR V430B VLINK Digital Pest Management User Guide
- June 1, 2024
- VICTOR
Table of Contents
VICTOR V430B VLINK Digital Pest Management
Product Overview
ACCOUNT SET-UP
- Before you begin, confirm that you have a VLINK account created and an Admin has added you to the account. Contact your VLINK sales representative for confirmation if you are unsure.
- Confirm that you can successfully log in at www.app.digitalpestmanagement.com.
CONNECT THE GATEWAY
- Plug in the gateway.
- For all other gateway instructions, contact your VLINK Sales Representative.
DOWNLOAD THE APP
- Search for the Victor VLINK Digital Pest Management app from the Apple App Store or Google Play Store and download it to your device.
- Log in using your VLINK account credentials.
- Follow the VLINK site set-up to ensure your deployment site is correctly set up in the VLINK app.
CONNECT TRAP TO THE NETWORK
- Remove the plastic battery pull tab at the front end of the trap.
- Press the power button to turn the trap on.
- You will see three green LED lights indicating that the trap is on.
- Follow the steps in the VLINK app to add the trap to the site.
LED Light Sequences
- 3 quick green flashes – trap powering on
- 3 quick red flashes – trap powering off
- 3 long green flashes – LoRa message successfully sent
- 1 long orange flash – trap is set
- 2 quick orange flashes – trap going into sleep mode.
BAIT TRAPS
Paste Baits
- Place paste baits in the bait cup container.
- Ensure bait is firmly in the cup to prevent it from being pulled out easily by the rodent.
- Placing bait on the trigger petal may lead to non-capture triggers.
Tied Baits
- Tie desired bait to raised Victor® V.
- Orient bait towards the middle of the trap pedal.
After Baiting
Pull back using thumb grips to set the trap. You will see 1 long orange flash
to indicate the trap is set, immediately followed by three long green flashes
to indicate a message has been sent.
Note: Setting the trap can only be accomplished if the trap is level. If
it is tilted significantly, it will not be set.
PLACE TRAP
Once your trap is connected, place it in the area of rodent activity and wait for the trap to alert you of a capture.
RESET THE TRAP AFTER A KILL
-
If a rodent has been captured, record your kill data using the VLINK Mobile App.
-
Once the rodent is removed, the trap is ready to be baited and reset for another capture.
-
To reset, simply pull the kill bar back to the set position and wait for the three green LED flashes to let you know the trap is communicating and ready for another kill.
-
The trap must send a message for the kill notification to clear.
Pro Tip: Avoid using strong cleaning products on the traps. -
A captured rodent can leave behind scent and odour that can make the trap more attractive to other rodents.
FCC STATEMENT
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications to this device are not expressly approved by
Woodstream The corporation could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, under Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used by the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
IC: This device complies with Industry Canada’s licence-exempt RSSs.
Operation is subject to the following two conditions: (1) This device may not
cause interference; and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
RF Exposure: This equipment complies with FCC and IC radiation exposure
limits set forth for an uncontrolled environment. This equipment should be
installed and operated with a minimum distance of 20cm between the radiator
and your body.
Manufactured for: Woodstream Corporation 69 N. Locust Street, Lititz, PA
17543 800-800-1819
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>