HILTI HIT-RE 500 V3 1400 Jumbo Injectable Adhesive Anchor Instruction Manual
- June 3, 2024
- HILTI
Table of Contents
HIT-RE 500 V3 1400 Jumbo Injectable Adhesive Anchor
Instruction Manual
HIT-RE 500 V3 1400 Jumbo Injectable Adhesive Anchor
Danger
Contains: 2,2‘-[(1-methy lethylidene)bis(4,1-pheny leneoxyme
thylene)]bisoxirane (A); Trimethy lolpropane triglycidylether (A);
2-methyl-1,5-pentanediamine (B); m- ylylenediamine(B);
Causes severe skin burns and eye damage (A, B) May cause an allergic skin
reaction (A, B) May cause respiratory irritation (B) Suspected of causing
genetic defects (A). May damage fertility or the unborn child (A) Toxic to
aquatic life with long lasting effects (A,B)
Adhesive anchoring system for rebar and anchor fastenings in concrete. Read
the safety instructions, general informations and warnings before using the
product.
| | |
---|---|---|---
Dry concrete| Water saturated concrete| Waterfilled borehole in concrete|
Submerged borehole in concrete
| | |
---|---|---|---
Hammer drilling| Diamond coring| Hollow drill bit| Roughening tool
| | |
---|---|---|---
Threaded rod| Threaded sleeve Rebar| Uncracked concrete| Cracked concrete
| | |
---|---|---|---
Working time| Initial curing time| Curing time| Roughening time
HAS-U, -HDG, -A4, -HCR / HIT-V, -F, -R / HAS / HAS-E
HIT-V
Ø d [mm] | Ø d0 [mm] | hef [mm] | Ø df [mm] | [Nm] |
---|---|---|---|---|
M12 | 14 | 70…240 | 14 | 40 |
M16 | 18 | 80…320 | 18 | 80 |
M20 | 22 | 90…400 | 22 | 150 |
M24 | 28 | 100…480 | 26 | 200 |
M27 | 30 | 110…540 | 30 | 270 |
M30 | 35 | 120…600 | 33 | 300 |
HIS (-N, -RN)![HILTI HIT-RE 500 V3 1400 Jumbo Injectable Adhesive Anchor
- fig 1](https://manuals.plus/wp-content/uploads/2022/12/HILTI-HIT- RE-500-V3-1400-Jumbo-Injectable-Adhesive-Anchor-fig-1.png)
Ø d [mm] | Ø d0 [mm] | hef [mm] | Ø df [mm] | hs [mm] | Tinst [Nm] |
---|---|---|---|---|---|
M8 | 14 | 90 | 9 | 8…20 | 10 |
M10 | 18 | 110 | 12 | 10…25 | 20 |
M12 | 22 | 125 | 14 | 12…30 | 40 |
M16 | 28 | 170 | 18 | 16…40 | 80 |
M20 | 32 | 205 | 22 | 20…50 | 150 |
Rebar
Ø d [mm] | Ø d0 [mm] | hef [mm] |
---|---|---|
12 | 14 | …1200 |
14 | 18 | …1400 |
16 | 20 | …1600 |
18 | 22 | …1800 |
20 | 25 | …2000 |
22 | 28 | …2200 |
24 | 32 | …2400 |
25 | 32 | …2500 |
26 | 35 | …2600 |
28 | 35 | …2800 |
30 | 37 | …3000 |
32 | 40 | …3200 |
36 | 45 | …3200 |
40 | 55 | …3200 |
Ø
| Ø
| HAS-U HIT-V
| HIS-N
| Rebar
---|---|---|---|---
d0 [mm]| d [mm]
14| 14*| 12| 8| 10
16| 16| −| −| 12
18| 18| 16| 10| 14
20| 20| −| −| 16
22| 22| 20| 12| 18
25| 25| −| −| 20
28| 28| 24| 16| 22
30| 30| 27| −| −
32| 32| −| 20| 24/25
35| 35| 30| −| 26/28
37| −| −| −| 30
40| −| −| −| 32
HIT-RB
|
HIT-SZ
| HIT-DL
| TE-YRT
---|---|---|---
[mm]| [mm]| | [mm]
14| 14| 14| 18
16| 16| 16| 20
18| 18| 18| 22
20| 20| 20| 25
22| 22| 20| 28
25| 25| 25| 30
28| 28| 25| 32
30| 30| 25| 35
32| 32| 32|
35| 35| 32|
37| 37| 32|
40| 40| 32|
HIT-DL: hef > 250 mm > 250 mm HIT-RB: hef > 20 x d
TE-CD 14: min. 61 l/s VC 20/40-Y no battery mode
Hilti VC 20/40 (-Y)
| | HIT-OHC
|
---|---|---|---
Ø d0 [mm]| HIT-…| Art. No.| Art. No.
| 14 … 20| OHC 1| 387551| 387550
22 … 32| OHC 2| 387552
| | |
---|---|---|---
d0 [mm]| [mm]| Art. No. 381215
…32| …1500| | ≥ 6 bar/90 psi
…55| …3200| –| ≥ 140 m³/h
| [°C]| twork| tcure, ini| tcure, full| [°F]
---|---|---|---|---|---
-5 … -1| 2 h| 48 h| 168 h| 23 … 31
0 … 4| 2 h| 24 h| 48 h| 32 … 40
5 … 9| 2 h| 16 h| 24 h| 41 … 49
10 … 14| 1.5 h| 12 h| 16 h| 50 … 58
15 … 19| 1 h| 8 h| 16 h| 59 … 67
20 … 24| 30 min| 4 h| 7 h| 66 … 76
25 … 29| 20 min| 3.5 h| 6 h| 77 … 85
30 … 34| 15 min| 3 h| 5 h| 86 … 94
35 … 39| 12 min| 2 h| 4.5 h| 95 …103
40| 10 min| 2 h| 4 h| 104
≥ +5 °C / 41 °F = 2x tcure
hef [mm]| ****troughen
0 … 100| 10 sec
101 … 200| 20 sec
201 … 300| 30 sec
301 … 400| 40 sec
401 … 500| 50 sec
501 … 600| 60 sec
troughen = hef [mm] / 10
troughen = hef [mm] / 10
| | hef| |
---|---|---|---|---
HIT-P 8000D| …40mm| …3200mm| -5 °C … 40 °C
23 °F … 104 °F| 5 °C … 40 °C
41 °F … 104 °F
| | hef| |
---|---|---|---|---
HIT-P 8000D| …28mm| …1000mm| -5 °C … 40 °C
23 °F … 104 °F| 5 °C … 40 °C
41 °F … 104 °F
![HILTI HIT-RE 500 V3 1400 Jumbo Injectable Adhesive Anchor
- fig 11](https://manuals.plus/wp-content/uploads/2022/12/HILTI-HIT- RE-500-V3-1400-Jumbo-Injectable-Adhesive-Anchor-fig-11.png)![HILTI HIT-RE 500 V3 1400 Jumbo Injectable Adhesive Anchor
- fig 13](https://manuals.plus/wp-content/uploads/2022/12/HILTI-HIT- RE-500-V3-1400-Jumbo-Injectable-Adhesive-Anchor-fig-13.png)![HILTI HIT-RE 500 V3 1400 Jumbo Injectable Adhesive Anchor
- fig 15](https://manuals.plus/wp-content/uploads/2022/12/HILTI-HIT- RE-500-V3-1400-Jumbo-Injectable-Adhesive-Anchor-fig-15.png)![HILTI HIT-RE 500 V3 1400 Jumbo Injectable Adhesive Anchor
- fig 17](https://manuals.plus/wp-content/uploads/2022/12/HILTI-HIT- RE-500-V3-1400-Jumbo-Injectable-Adhesive-Anchor-fig-17.png)![HILTI HIT-RE 500 V3 1400 Jumbo Injectable Adhesive Anchor
- fig 19](https://manuals.plus/wp-content/uploads/2022/12/HILTI-HIT- RE-500-V3-1400-Jumbo-Injectable-Adhesive-Anchor-fig-19.png)![HILTI HIT-RE 500 V3 1400 Jumbo Injectable Adhesive Anchor
- fig 21](https://manuals.plus/wp-content/uploads/2022/12/HILTI-HIT- RE-500-V3-1400-Jumbo-Injectable-Adhesive-Anchor-fig-21.png)![HILTI HIT-RE 500 V3 1400 Jumbo Injectable Adhesive Anchor
- fig 23](https://manuals.plus/wp-content/uploads/2022/12/HILTI-HIT- RE-500-V3-1400-Jumbo-Injectable-Adhesive-Anchor-fig-23.png)![HILTI HIT-RE 500 V3 1400 Jumbo Injectable Adhesive Anchor
- fig 25](https://manuals.plus/wp-content/uploads/2022/12/HILTI-HIT- RE-500-V3-1400-Jumbo-Injectable-Adhesive-Anchor-fig-25.png)![HILTI HIT-RE 500 V3 1400 Jumbo Injectable Adhesive Anchor
- fig 27](https://manuals.plus/wp-content/uploads/2022/12/HILTI-HIT- RE-500-V3-1400-Jumbo-Injectable-Adhesive-Anchor-fig-27.png)
Adhesive anchoring system for rebar and anchor fastenings in concrete
▶ Prior to use of product, follow the instructions for use and the legally
obligated safety precautions.
▶ See the Safety Data Sheet for this product.
Hilti HIT-RE 500 V3
Contains:
2,2‘-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane (A);
Trimethylolpropane triglycidylether (A); 2-methyl-1,5-pentanediamine (B);
m-Xylylenediamine (B);
Danger
H314 | Causes severe skin burns and eye damage.(A,B) |
---|---|
H317 | May cause an allergic skin reaction.(A,B) |
H335 | May cause respiratory irritation (B) |
H341 | Suspected of causing genetic defects (A) |
H360 | May damage fertility or the unborn child (A) |
H411 | Toxic to aquatic life with long lasting effects.(A,B) |
P280 | Wear protective gloves/protective clothing/eye protection/face |
protection.
P262| Do not get in eyes, on skin, or on clothing
P302+P352| IF ON SKIN: Wash with plenty of soap and water.
P305+P351+P338| IF IN EYES: Rinse cautiously with water for several minutes.
Remove contact lenses, if present and easy to do. Continue rinsing.
P333+P313| If skin irritation or rash occurs: Get medical advice/attention.
P337+P313| If eye irritation persists: Get medical advice/attention.
Recommended protective equipment:
Eye protection: Tightly sealed safety glasses e.g.: #02065449 Safety glasses
PP EY-CA NCH clear;
#02065591 Goggles PP EY-HA R HC/AF clear;
Protective gloves: EN 374 ; Material of gloves: Nitrile rubber, NBR
Avoid direct contact with the chemical/ the product/ the preparation by
organizational measures.
Final selection of appropriate protective equipment is in the responsibility
of the user
Disposal considerations
Empty packs:
▶ Leave the Mixer attached and dispose of via the local Green Dot collecting
system
– or EAK waste material code 15 01 02 plastic packaging.
Full or partially emptied packs:
▶ dispose of as special waste in accordance with official regulations.
- EAK waste material code: 20 01 27* paint, inks, adhesives and resins containing dangerous substances.
- or waste material code: EAK 08 04 09* waste adhesives and sealants containing organic solvents or other dangerous substances.
Content: 1400 ml / 47.3 fl.oz
Weight: 1980 g / 69.8 oz
Warranty: Refer to standard Hilti terms and conditions of sale for
warranty information.
Failure to observe these installation instructions, use of non-Hilti anchors,
poor or questionable concrete conditions, or unique applications may affect
the reliability or performance of the fastenings.
Product Information
- Always keep this instruction for use together with the product.
- Ensure that the instruction for use is with the product when it is given to other persons.
- Safety Data Sheet: Review the SDS before use.
- Check expiration date: See expiration date imprint on foilpack manifold (month/year). Do not use expired product.
- Foil pack temperature during usage: +5 °C to 40 °C / 41 °F to 104 °F.
- Conditions for transport and storage: Keep in a cool, dry and dark place between +5 °C to 25 °C / 41 °F to 77 °F.
- For any application not covered by this document / beyond values specified, please contact Hilti.
- Partly used foil packs must be used up within one week. Leave the mixer attached on the foil pack manifold in the dispenser and do not retract the pistons! Remove the air pressure hose and store under the recommended storage conditions. If reused, attached a new mixer and discard the initial quantity of anchor adhesive.
WARNING
Improper handling may cause mortar splashes. Eye contact with mortar may cause
irreversible eye damage!
- Always wear tightly sealed safety glasses, gloves and protective clothes before handling the mortar!
- Never start dispensing without a mixer properly screwed on.
- When using an extension hose: Discard of initial mortar flow must be done through supplied mixer only (not through the extension hose).
- Attach a new mixer prior to dispensing a new foil pack (snug fit).
- Caution! Never remove the mixer while the foil pack system is under pressure.
- Use only the type of mixer supplied with the adhesive. Do not modify the mixer in any way.
- Dropping foil packs, also foil packs already inserted into the foil pack holder, is likely to cause damage leading to mal function.
- Never use damaged foil packs and/or damaged or unclean foil pack holders.
**** Poor load values / potential failure of fastening points due to inadequate borehole cleaning. The boreholes must be dry and free of debris, dust, water, ice, oil, grease and other contaminants prior to adhesive injection.
- Hilti hollow drill bits TE-CD, TE-YD must be used in conjunction with a properly maintained Hilti vacuum cleaner with model and suction capacity (volumetric flow rate) as specified in the accessory table.
- For blowing out the borehole – blow out with oil free air until return air stream is free of noticeable dust.
- For flushing the borehole – flush with water line pressure until water runs clear.
- Important! Remove all water from the borehole and blow out with oil free compressed air until borehole is completely dried before mortar injection (not applicable to hammer drilled hole in underwater application).
**** Ensure that boreholes are filled from the back of the boreholes without forming air voids.
-
If necessary, use the accessories / extensions to reach the back of the borehole.
-
For overhead applications use the overhead accessories HIT-SZ / IP and take special care when inserting
the fastening element. Excess adhesive may be forced out of the borehole. Make sure that no mortar drips onto the installer. -
If a new mixer is installed onto a previously-opened foil pack, the first trigger pulls must be discarded.
Due to the heat generation during curing, metal element (rod) must be
set within the allowed working time or wood (the base material) may be
negatively effected.
Not adhering to these setting instructions can result in failure of
fastening points.
Hilti (Gt. Britain) Ltd.
1 Trafford Wharf Road
Trafford Park, GB-M17 1BY Manchester
Tel +44 161 886 1000
**** | **** | **** | **** |
---|
21
Hilti AG
FL-9494 Schaan
Hilti Werke
2873-CPR-201-64
ETA-20/0125
Notified Body 2873
EAD 330087-00-0601-v01
www.hilti.group| 21
Hilti AG
FL-9494 Schaan
Hilti Werke
2873-CPR-201-48
ETA-19/0194
Notified Body 2873
EAD 130006-00-0304
www.hilti.group| 21
Hilti AG
FL-9494 Schaan
Hilti Werke
2873-CPR-201-22
ETA-16/0142
Notified Body 2873
EAD 331522-00-0601
www.hilti.group| 21
Hilti AG
FL-9494 Schaan
Hilti Werke
2873-CPR-201-23
ETA-16/0143
Notified Body 2873
EAD 330499-01-0601
www.hilti.group
| | ****
---|---|---
21
Hilti AG
FL-9494 Schaan
Hilti Werke
2873-CPR-201-40
ETA-18/0745
Notified Body 2873
EAD 332077-00-0601
www.hilti.group| 21
Hilti AG
FL-9494 Schaan
Hilti Werke
2873-CPR-201-24
ETA-16/0180
Notified Body 2873
ETAG 001-1, -5 Option 1
www.hilti.group| 21
Hilti AG
FL-9494 Schaan
Hilti Werke
2873-CPR-201-74
ETA-20/0697
Notified Body 2873
EAD 332347-00-0601
www.hilti.group
Certified to NSF/ANSI/CAN61
Info Shop
http://qr.hilti.com/r4929903
Made in Germany
Hilti = registered trademark of Hilti Corporation, Schaan, Liechtenstein
www.hilti.group
Printed in Germany © 2022
Right of technical changes reserved S.E. & O. 414647 V07-04.2022
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>