HILTI HIT-RE 10 Injectable Mortar Instruction Manual
- October 30, 2023
- HILTI
Table of Contents
HILTI HIT-RE 10 Injectable Mortar Instruction Manual
Hilti HIT-RE 10
580ml / 19.61 fl. oz
900g / 31.71 oz
Adhesive anchoring system for rebar and anchor fastenings in concrete. Read the safety precautions, safety data sheet and the product information before use.
Recommended protective equipment:
Eye protection: Tightly sealed safety glasses e.g.: #02065449 Safety glasses
PP EY-CA NCH clear;
02065591 Goggles PP EY-HA R HC/AF clear;
Protective gloves: EN 374 ; Material of gloves: Nitrile rubber, NBR Avoid
direct contact with the chemical/ the product/ the preparation by
organizational measures.
Final selection of appropriate protective equipment is in the responsibility
of the user.
Product information
- Safety Data Sheet: Review the SDS before use.
- Check expiration date: See expiration date imprint on cartridge label (month/year). Do not use expired product.
- Cartridge temperature during usage: +10 °C to 40 °C / 50 °F to 104 °F.
- Conditions for transport and storage: Keep in a cool, dry and dark place between +5 °C to 25 °C / 41 °F to 77 °F.Partly used cartridges must be used up within 4 weeks. Leave the mixer or the cap attached on the cartridge and store under the recommended storage conditions. If reused, attach a new mixer and discard the initial quantity of anchor adhesive.
- For any application not covered by this document / beyond values specified, please contact Hilti.
- If hardened epoxy is detected in cartridge neck carefully removed it to prevent blockage in the mixer.
WARNING
Improper handling may cause mortar splashes. Eye contact with mortar may cause irreversible eye damage!
- Always wear tightly sealed safety glasses, gloves and protective clothes before handling the mortar!
- Never start dispensing without a mixer properly screwed on. Before start make sure cartridge is properly inserted into the dispenser.
- When using an extension hose: Discard of initial mortar flow must be done through supplied mixer only (not through the extension hose).
- Never remove the mixer while the cartridge is under pressure. Press the release button of the dispenser to avoid mortar splashing.
- Use only the type of mixer supplied with the adhesive. Do not modify the mixer or the cartridge in any way.
- Never use damaged cartridges
Poor load values / potential failure of fastening points due to inadequate borehole cleaning.
- The boreholes must be dry and free of debris, dust, water, ice, oil, grease and other contaminants prior to adhesive injection.
- For blowing out the borehole – blow out with oil free air until return air stream is free of noticeable dust.
- Important! Remove all water from the borehole and blow out with oil free compressed air until borehole is completely dried immediately before mortar injection.
- For brushing the borehole – only use specified wire brush. The brush must resist insertion into the borehole – if not the brush is too small and must be replaced.
Ensure that boreholes are filled from the back of the boreholes without forming air voids.
- If necessary, use the accessories / extensions to reach the back of the borehole.
- For overhead applications use the overhead accessories HIT-SZ / IP and take special care when inserting the fastening element. Excess adhesive may be forced out of the borehole. Make sure that no mortar drips onto the installer.
Warranty: Refer to standard Hilti terms and conditions of sale for
warranty information.
Failure to observe these installation instructions, use of non-Hilti anchors,
poor or questionable concrete conditions, or unique applications may affect
the reliability or performance of the fastenings.
AR Hilti Argentina S.R.L.
Profesor Manuel García 4760
B1605 BIB – Munro
AR-Buenos Aires
Tel +54 11 4721 4400
Fax +54 11 4721 4410
BR Hilti do Brasil Comercial Ltda.
Al. Rio Negro, 500 -Torre A,
9° andar
06454-000 Barueri, SP
Tel +55 11 4134 9000
Fax +55 11 4134 9072
CA Hilti (Canada) Corp.
2360 Meadowpine Boulevard
Mississauga, Ontario L5N 6S2
Tel +1 905 813 9200
Fax +1 905 813 9009
CL Hilti Chile Ltda.
Av. Apoquindo 4501, piso 13
Las Condes 7550000 Santiago,
Tel +562 655 3000
Fax +562 426 1974
CO Hilti Colombia S.A.S
Carrera 16A No 78-55 Piso 2
Bogotá, Colombia
Tel +57 (1) 519 0001
Fax +57 422 2300 Ext 1911
MX Hilti Mexicana, S.A. de C.V.
Jaime Balmes 8, Oficina 102,
1er Piso
Col. Los Morales Polanco
Del. Miguel Hidalgo
MEX-Mexico City 11510
Tel +5255 5387-1600
Fax +5255 5281 1419
PE Hilti Perú S.A.
Av. Javier Prado Este
Nro. 499 Int. 1103
Golf los Inkas
Santiago de Surco, PE-Perú 15023
Tel +51 (0) 800 44 584
PR Hilti Caribe, LLC
The Palmas Village #3,
Carr. 869 KM 2
Palmas Industrial Park
Cataño, PR 00962
Tel +1-787 936-7060
Fax +1 787 936-7065
US Hilti Inc.
Legacy Tower, Suite 1000,
7250 Dallas Parkway
Plano, TX 75024
Tel +1 972 403 5800
Fax +1 918 254 0522
VE Hilti Venezuela, S.A.
Calle Pascuale Giorgio, 3era.
Transversal, Edf. Segre,
2do Piso, Ala Norte, Los Ruices
VE-Caracas 1071
Tel +58 212 232 42 43
Fax +58 212 203 4310
Made by Hilti in China
Hilti = registered trademark of Hilti Corporation, Schaan, Liechtenstein
© 2019
Right of technical changes reserved S.E. & O,
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>