kemi Sports Bluetooth Headset User Guide
- June 3, 2024
- kemi
Table of Contents
kemi Sports Bluetooth Headset
Schematic diagram and accessories
- Microphones
- TPY-C charging port
- “ + ” Key/switch composite key
- “ – ” Key
- Memory metal back hang
- Breathing lights
Parts list
- Headset
- TYP-C charging cable
- Instruction Manual (including Warranty Card)
Instructions
Roll Camera
Long press the power button for about 3 seconds. When the red and blue light alternately flashes, it means the earphone has been turned on
Bluetooth connection
When the headset is turned on properly for the first time, it will enter the Bluetooth pairing state when the phone is blue search for “X50Pro in the tooth setting After the connection is successful the indicator light turns off and the blue light flashes once in 5 seconds
Replacement of matching equipment and reconnection
Disconnect the current paired device from Bluetooth, the headset indicator flashes red and blue alternately, and the other device is Search for “ X50 Pro ” and click connect
The “ X50Pro ” headphone
supports automatic back connection and matching device, which will be automatically connected after normal power-on For the last connected device, make sure the front end (E. G. , Mobile Bluetooth) is open properly.
Turn it off
Long press “ + ” to open the key for about 3 seconds, it will shut down.
Indicator light goes out.
Charging
Normal connection, the phone will display the headphone battery, such as the
battery display red, that is, the meter
Show the need to charge, plug in the charging line to charge.
Note: 5V charging devices such as mobile phone chargers can be charged
Instructions for + key compound machine
- Long press “ + ” button —— headset switch machine
- Long press the “ – ” button for 1 second to wake up Siri
- Press and hold the “-” button for 3 seconds: turn on and off the night running breathing light
State of play
- Double-click the “ + ” button —— to pause the playback
- Press and hold the “ + ” key for 1 second —— for the next song
- Double click the” – ” key——Last song
- Click the “ + ”key —— volume plus
- Click the “ – ” key —— Volume Subtraction
Call status
- Click the “ + ” key —– to answer the call
- Press and hold the “ + ” key for 1 second—– to hang up
- Press and hold the “ + ” key for 1 second—– Refuse to accept
Indicator light description
- Alternate red and blue: pairing state
- Lights out : Connect successfully and wait for playback
- The red light is always on : charging
- Blue light always on : full charge
Troubleshooting
Unable to boot
Determine whether the headset is fully charged, whether the button is misoperated, and then charge and activate.
Unable to connect to Bluetooth
Whether the headphone indicator is in the alternately flashing stage of red and blue
Can’t back to even
Make sure the front end (e.g., Bluetooth) is open properly.
Headphone volume is low
Whether the phone increases the volume, the phone needs to increase or decrease the volume. Wearing a way Whether it is right
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution : Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure co
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>