TELTONIKA NETWORK RUT360 User Manual

RUT360

HARDWARE

FRONT VIEW

BACK VIEW

POWER SOCKET PINOUT

FEATURES

Mobile

Mobile module| 4G (LTE) – Cat 6 up to 300 Mbps, 3G – Up to 42 Mbps
Status| Signal strength, SINR, RSRP, RSRQ, Bytes sent/received, connected band, carrier aggregation, IMSI, ICCID
SMS| SMS status, SMS configuration, send/read SMS via HTTP POST/GET, Email to SMS, SMS to Email, SMS to HTTP, SMS to SMS, SMS

auto reply

USSD| Supports sending and reading Unstructured Supplementary Service Data messages
Black/Whiles list (planned)| Operator black/white list
Multiple PDN| Possibility to use different PDNs for multiple network access and services
Band management| Band lock, Used band status display
APN| Auto APN
Bridge mode| Direct connection (bridge) between mobile ISP and device on LAN
WIRELESS
Wireless mode| 802.11 b/g/n, 2×2 MIMO, Access Point (AP), Station (STA)
WiFi security| WPA3-EAP, WPA3-SAE, WPA2-Enterprise-PEAP, WPA2-PSK, WEP; AES- CCMP, TKIP, Auto Cipher modes, client separation
ESSID| ESSID stealth mode
Wireless Hotspot| Captive portal (Hotspot), internal/external Radius server, SMS OTP, MAC auth, built-in customizable landing page, walled garden
ETHERNET
WAN| 1 x WAN port (can be configured as LAN) 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX crossover
LAN| 1 x LAN ports, 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX crossover
NETWORK
Routing| Static routes, Dynamic routes (planned)
VoIP passthrough support| H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets
Network protocols| TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, FTP (planned), SMTP, SSL v3, TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet client, SNMP (planned), MQTT (planned), Wake on LAN (WOL) (planned)
Connection monitoring| Ping Reboot, Wget reboot, Periodic Reboot, LCP and ICMP for link inspection
Firewall| Port forwards, traffic rules, NAT rules, custom rules
DHCP| Static and dynamic IP allocation, DHCP Relay, Relayd
QoS / Smart Queue Management (SQM) (planned)| Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e
DDNS (planned)| Supported >25 service providers, others can be configured manually
Network backup| Mobile, Wired and WiFi WAN options, each of which can be used as an automatic Failover
Load balancing| Balance Internet traffic over multiple WAN connections
SSHFS (optional)| Possibility to mount remote file system via SSH protocol (not available in standard FW)
SECURITY
Authetication| Pre-shared key, digital certificates, X.509 certificates
Firewall| Pre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI; DMZ; NAT; NAT-T
Attack prevention| DDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN- RST, X-mas, NULL flags, FIN scan attacks)
VLAN| Tag based VLAN separation
Mobile quota control| Custom data limits for both SIM cards
WEB filter (planned)| Blacklist for blocking out unwanted websites, Whitelist for specifying allowed sites only
Access control| Flexible access control of TCP, UDP, ICMP packets, MAC address filter
VPN
OpenVPN| Multiple clients and a server can run simultaneously, 12 encryption methods
OpenVPN Encryption| DES-CBC, RC2-CBC, DES-EDE-CBC, DES-EDE3-CBC, DESX-CBC, BF- CBC, RC2-40-CBC, CAST5-CBC, RC2-64-CBC, AES-128-CBC, AES-192-CBC, AES-256-CBC
IPSec| IKEv1, IKEv2, with 5 encryption methods for IPsec (DES, 3DES, AES128, AES192, AES256)
GRE| GRE tunnel
PPTP, L2TP| Client/Server instances can run simultaneously, L2TPv3 support (planned)
Stunnel (planned)| Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program’s code
DMVPN (planned)| Method of building scalable IPsec VPNs
SSTP (planned)| SSTP client instance support
ZeroTier| ZeroTier VPN client support
WireGuard| WireGuard VPN client and server support
MODBUS TCP SLAVE (PLANNED)
ID filtering| Respond to one ID in range [1;255] or any
Allow remote access| Allow access through WAN
Custom registers| Modbus TCP custom register block, which allows to read/write to a file inside the router, and can be used to extend Modbus TCP slave functionality
MODBUS TCP MASTER (PLANNED)
Supported functions| 01, 02, 03, 04, 05, 06, 15, 16
Supported data formats| 8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII
MQTT GATEWAY (PLANNED)
Gateway| Allows sending commands and receiving data from Modbus Master trough MQTT broker
DATA TO SERVER (PLANNED)
Protocols| HTTP(S), MQTT, Azure MQTT, Kinesis
MONITORING & MANAGEMENT
WEB UI| HTTP/HTTPS, status, configuration, FW update, CLI, troubleshoot, event log, system log, kernel log
FOTA| Firmware update from server, automatic notification
SSH| SSH (v1, v2)
SMS| SMS status, SMS configuration, send/read SMS via HTTP POST/GET
CALL| Reboot, Status, Mobile data on/off, Output on/off
MQTT (planned)| MQTT Broker, MQTT publisher
SNMP (planned)| SNMP (v1, v2, v3), SNMP trap
JSON-RPC| Management API over HTTP/HTTPS
Modbus (planned)| Modbus TCP status/control
RMS| Teltonika Remote Management System (RMS)
IoT PLATFORMS
Clouds of things| Allows monitoring of: Device data, Mobile data, Network info, Availability
ThingWorx| Allows monitoring of: WAN Type, WAN IP, Mobile Operator Name, Mobile Signal Strength, Mobile Network Type
Cumulocity| Allows monitoring of: Device Model, Revision and Serial Number, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, Signal Strength, WAN Type and IP
Azure IoT Hub| Can send device IP, Number of bytes send/received, Mobile connection state, Network link-state, IMEI, ICCID, Model, Manufacturer, Serial, Revision, IMSI, SIM State, PIN state, GSM signal, WCDMA RSCP, WCDMA EC/IO, LTE RSRP, LTE SINR, LTE RSRQ, CELL ID, Operator, Operator number, Connection type, Temperature, PIN count to Azure IoT Hub server
SYSTEM CHARACTERISTICS
CPU| QCA9531, MIPS 24kc, 650 MHz
RAM| 128 MB, DDR2
FLASH storage| 16 MB, SPI Flash
FIRMWARE / CONFIGURATION
WEB UI| Update FW from file, check FW on server, configuration profiles, configuration backup
FOTA| Update FW/configuration from server
RMS| Update FW/configuration for multiple devices at once
Keep settings| Update FW without losing current configuration
INPUT/OUTPUT
Configurable I/O| 2 x Configurable digital Inputs/Outputs. Digital input 0 – 6 V detected as logic low, 8 – 30 V detected as logic high. Open collector output, max output 30 V, 300 mA
Events| SMS, Email, RMS
POWER
Connector| 4 pin industrial DC power socket
Input voltage range| 9 – 30 VDC, reverse polarity protection, voltage surge/transient protection
Power consumption| 10.5 W max
PHYSICAL INTERFACES (PORTS, LEDS, ANTENNAS, BUTTONS, SIM)
Ethernet| 2 x RJ45 ports, 10/100 Mbps
I/Os| 2 x Configurable digital Inputs/Outputs on 4 pin power connector
Status LEDs| 2 x Mobile connection type, 3 x Mobile connection strength, 2 x Eth status, 1 x Power
SIM| 1 x SIM slots (Mini SIM – 2FF), 1.8 V/3 V, external SIM holders
Antenna| 2 x SMA for LTE, 2 x RP-SMA for WiFi
Power| 1 x 4 pin DC connector
Reset| Reboot/User default reset/Factory reset button
PHYSICAL SPECIFICATION
Casing material| Aluminium housing with DIN rail mounting option
Dimensions (W x H x D)| 100 x 30 x 85 mm
Weight| 247 g
Mounting options| DIN rail, flat surface placement
OPERATING ENVIRONMENT
Operating temperature| -40 C to 75 C
Operating humidity| 10 % to 90 % non-condensing

HARDWARE INSTALLATION

1. Push the SIM button with the SIM needle.
2. Pull out the SIM holder.
3. Insert your SIM card into the SIM holder.
4. Slide the SIM holder back into the router.
5. Attach Mobile and WiFi antennas.
6. Connect the power adapter to the socket on the front of the device. Then plug the other end of the power adapter into a power outlet.
7. Connect to the device wirelessly using SSID and password provided on the device information label or use an Ethernet cable connected to LAN port.
   

LOGIN TO DEVICE

1. To enter the router’s Web interface (WebUI), type http://192.168.1.1 into the URL field of your Internet browser.
2. Use login information shown in image A when prompted for authentication.
3. After you log in, you will be prompted to change your password for security reasons. The new password must contain at least 8 characters, including at least one uppercase letter, one lowercase letter, and one digit. This step is mandatory, and you will not be able to interact with the router’s WebUI before you change the password.
4. When you change the router’s password, the Configuration Wizard will start. The Configuration Wizard is a tool used to set up some of the router’s main operating parameters.
5. Go to the Overview page and pay attention to the Signal Strength indication (image B). To maximize the cellular performance try adjusting the antennas or changing the location of your device to achieve the best signal conditions.
   

TECHNICAL INFORMATION

Radio specifications

RF technologies| 3G, 4G, WiFi
Max RF power| 24 dBm@WCDMA, 23 dBm@LTE, 20 dBm@WiFi

**Bundled accessories specifications***

Power adapter| Input: 0.6 A@100-240 VAC, Output: 12 VDC, 1.5 A, 4 pin plug
Mobile antenna| 698~960/1710~2690 MHz, 50 Ω, VSWR<3, gain 4 dBi, omnidirectional, SMA male connector
WiFi antenna| 2400~2483.5 MHz, 50 Ω, VSWR<2, gain 5 dBi, omnidirectional, RP-SMA male connector

*Order code dependent.
**Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for the compliance with the legal regulations.

WHAT’S IN THE BOX?

STANDARD PACKAGE CONTAINS

• RUT360
• 18 W Euro PSU
• 2 x LTE antennas (swivel, SMA male)
• 2 x WiFi antenna (swivel, RP-SMA male)
• Ethernet cable (1.5 m)
• QSG (Quick Start Guide)
• RMS Flyer
• Packaging box
  

RUT360

|

2 X LTE ANTENNAS (SWIVEL, SMA MALE)

|

2 X WIFI ANTENNA (SWIVEL, RP-SMA
MALE)

---|---|---

18 W EURO PSU

|

ETHERNET CABLE (1.5 M)

|

STANDARD ORDER CODES

For more information on all available packaging options ­ please contact us directly.

HTS CODE 8517.62.00

STANDARD ORDER CODES

B28, B321
• 4G (LTE-TDD): B38, B40, B41
• 3G: B1, B3, B5, B8
RUT360 1*****| North America| • 4G (LTE-FDD): B2, B4, B5, B7, B12, B13, B25, B26, B291, B30, B66
• 3G: B2, B4, B5

The price and lead-times for region (operator) specific versions may vary. For more information please contact us.
1 – LTE-FDD B29 and B32 support receiving only, and are only for secondary component carrier in 2×CA
2 – Excluding Japan and CMCC

MOUNTING OPTIONS

DIN RAIL KIT

DIN RAIL KIT

• DIN Rail adapter
• Philips Pan Head screw #6-32×3/16, 2pcs for RUT2xx/RUT9xx
  

For more information on all available packaging options ­ please contact us directly.

COMPACT DIN RAIL KIT

DIN RAIL KIT

• Compact plastic DIN Rail adapter (70x25x14,5mm)
• Philips Pan Head screw #6-32×3/16, 2pcs
  

For more information on all available packaging options ­ please contact us directly.

SURFACE MOUNTING KIT

DIN RAIL KIT

• Surface mounting kit
• Philips Pan Head screw #6-32×3/16, 2pcs
  

For more information on all available packaging options – please contact us directly.

RUT360 SPATIAL MEASUREMENTS & WEIGHT

MAIN MEASUREMENTS

W x H x D dimensions for RUT360:

Device housing*: 100 x 30 x 85
Box: 173 x 71 x 148

*Housing measurements are presented without antenna connectors and screws; for measurements of other device elements look to the sections below.

TOP VIEW
The figure below depicts the measurements of RUT360 and its components as seen from the top:
RIGHT VIEW
The figure below depicts the measurements of RUT360 and its components as seen from the right side:
FRONT VIEW
The figure below depicts the measurements of RUT360 and its components as seen from the front panel side:

REARVIEW
The figure below depicts the measurements of RUT360 and its components as seen from the back panel side:

MOUNTING SPACE REQUIREMENTS
The figure below depicts an approximation of the device’s dimensions when cables and antennas are attached:

DIN RAIL
The scheme below depicts protrusion measurements of an attached DIN Rail:

Copyright © 2021, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>