kemi X7 Bone Conduction Bluetooth Earphone Instruction Manual

kemi X7 Bone Conduction Bluetooth Earphone

Instructions for usage

Charge

The headphone with a rechargeable battery , the first use of the headset must be fully charged to the battery . In use , if the voice “ Di-Di ” prompting low power , that the battery is low , then you need to charge the headset . the charging cable should be connected to the headset’s magnetic charging port , about 2 hours to fill . Charging status indicator flashing breathing light , full charge often blue light .
Note : Magnetic charging has a positive and negative pole corresponds to each other adsorption can be charged normally , mustual repulsion can not be charged or even cause a short circuit .
Warning : The rechargeable battery of this product must be properly disposed of for recycling . please do not put the battery into the fire ,so as not to cause an explosion . Operating instruction

Music Play

Answer the phone

Operating instruction

How to pair with Bluetooth
Bluetooth pairing: In the off state, press and hold the The power button for 3 to 5 seconds, the indicator light will enter the red and blue light flashing state, and then enter the pairing state. Turn on the Bluetooth (mobile phone / computer) on the device and search for the device name ” X7 “, Click the device” X7 “to pair and connect. Bluetooth / MP3 mode switching: Double click the power button (mode) power button freeSwitch bluetooth and memory mode.
Note: Bluetooth mode is default for boot

AI intelligent voice control

Note: In the Bluetooth connection status, touch the multi-function button on the right for 1 second to wake up. After hearing the prompt, you can voice control the phone, saving time to operate the phone, fast and smart

Indicator

Product parameter

• Charging time: About 2 hours
• Distance: Bluetooth 10 meter
• Version: 5.3
• Input: 5V/500mA
• Battery: 200mAh
• Play: More than 6 hours@65% volume
• Agreement: A2DP, AVRCP, HSP, HFP
• Music format support: MP3, WMA, WAV, APE, FLAC

Care and cleaning

• The headset can not soak seawater / salt water for a long time , filling the magnetic suction part is easy to corrode .
• If not used for a long time , please at least once a month full of electricity .
• Please do not disassemble any parts of the product, if you find that the product has defects , that is ,stop using the product , contact the sales side after sales service.
• Please wipe the water on the surface of the headset after each movement , especially the charging port , to deal with clean in time to prevent port ,affecting the life of the charging port ,affecting the life of the product.
• Keep the product away from fire ,heat,freezing sources, chemicals, violent impact disassembly and extrusion products are strictly prohibited .
• Please use a charging head with an output of 5V1A or less .

Product warranty card

This card is a product warranty certificate, please keep it properly

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>