MeTra AX-TOY28SWC Steering Wheel Control Harness Instruction Manual
- June 3, 2024
- Metra
Table of Contents
Installation Instructions for AX-TOY28SWC
AX-TOY28SWC Plug and Play Harness for the ASWC-1
(sold separately) 2012-up
FEATURES
- Plug and play harness for the ASWC-1 (sold separately)
- Retains the factory AUX-IN jack
INTERFACE COMPONENTS
- AX-TOY28SWC harness
TOOLS REQUIRED
- Cutting tool
- Crimping tool
- Tape
- Connectors (example: butt-connectors, bell caps, etc.)
APPLICATIONS
SCION
tC| 2014-2015
SUBARU
Forester (w/ nav)| 2014-2015
Forester (w/ SD based nav)| 2012-2013
Impreza WRX (w/ nav)| 2013-2014
Legacy 2015| 2015
Legacy (w/ HK amp)| 2012-2013
Outback 2015| 2015
Outback (w/ HK amp)| 2012-2013
WRX (w/ nav) 2015| 2015
XV Crosstrek (w/ nav)| 2013-2014
LEXUS
CT 200h| 2011-2015
TOYOTA
4-Runner| 2013-2015
Avalon| 2013-2015
Camry| 2012-2015
Corolla| 2013-2015
Corolla (w/ nav)| 2011-2015
FJ Cruiser (w/ nav)| 2013
Highlander| 2013-2015
Matrix (w/ USB)| 2013
Prius V| 2012-2015
Prius C| 2012-2015
Prius| 2012-2015
Rav-4| 2012-2015
Sequoia (w/ nav)| 2013-2015
Tacoma| 2013-2015
Tundra| 2014-2015
Venza| 2013-2015
Yaris Hatchback| 2012-2015
CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.
Connections to be made
From the AX-TOY28SWC harness to the aftermarket radio:
- Connect the Black wire to the ground wire.
- Connect the Red wire to the accessory wire.
- Connect the Red and White RCA jacks to the audio AUX-IN jacks (if so equipped).
The following (2) wires are for aftermarket multimedia/navigation radios that provide these wires (if not required, tape them off and disregard them):
- Connect the Light Green wire to the parking brake wire (if applicable).
- Connect the Green/Purple wire to the reverse wire (if applicable).
Installing the AX-TOY28SWC
- With the key in the off position, connect the AX-TOY28SWC harness into the ASWC-1 (sold separately), and then into the vehicle.
- Follow the instructions included with the ASWC-1 (sold separately) for connections to the 3.5mm jack.
- With all connections completed, reconnect the negative battery terminal.
Programming the ASWC-1 (sold separately)
When using the ASWC-1 to retain steering wheel audio controls:
-
Turn the key to ignition; the L.E.D. in the ASWC-1 (sold separately) will flash fast.
Note: If your vehicle has a RETURN button on the steering wheel, press and hold that button during this process. -
After about 20 seconds the L.E.D. will light up solid indicating the ASWC-1 (sold separately) has been programmed. If the L.E.D. does not light up solid, or the steering wheel controls do not work, refer to the instructions included with the ASWC-1 (sold separately) for troubleshooting.
IMPORTANT WARNING
This product includes instructions for installation which must be carefully
followed. The instructions are worded in such a manner to assume that the
installer is capable of completing these type of electronic installations. If
you are unclear as to what you are instructed to do or believe that you do not
understand the instructions so as to properly and safely complete the insta
llation you should consult a technician who does have thisknowledge and
understanding.
Failure to follow these instructions carefully and to install the interface as
described could cause harm to the vehicle or to safety systems on the vehicle.
Interference with certain safety systems could cause harm to persons as well.
If you have any questions in this regard please call the Help line or Metra at
1-800-221-0932 for assistance.
1-800-221-0932
metraonline.com
REV. 2/29/16
© COPYRIGHT 2004-2016
http://axxessinterfaces.com/
METRA ELECTRONICS CORPORATION
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>