ECOXGEAR GDI-EXSNDXTR01 SoundExtreme 500w Powersports Amplified Soundbar User Guide
- June 3, 2024
- Ecoxgear
Table of Contents
GDI-EXSNDXTR01 SoundExtreme 500w Powersports Amplified Soundbar
What’s in the Box
SoundExtreme Speaker
8ft Power Cable
SoundExtreme SE26
Models: GDI-EXSNDXTR00…20
POWERSPORTS AMPLIFIED SOUNDBAR
Auxiliary Power Out Mating Connector
User Guide
SoundExtreme SoundExtreme User Guide Remote Control
(2x) ¼-20 SHCS Bolt 3.5″ long
(2x) Rubber Allen Wrench (2x) ¼-20 SHCS (2x) ¼-20 Stud
Sleeves
for ¼-20
Bolt 2 long
1.5 long
(2x) ¼-20 SHCS (2x) ¼-20 SHCS Bolt 1.25 long Bolt 0.5 long
(2x) Mounts
(8x) #8-32 Button (2x) ¼-20
Head Bolts
Washer (S)
(2x) Rubber (4x) Worm Clamps (2x) ¼-20
Feet
– ½ Width
Washer (L)
20
(2x) ¼-20 Nut
SoundExtreme SE26
Models: GDI-EXSNDXTR00…20
POWERSPORTS AMPLIFIED SOUNDBAR
User Guide 1
SoundExtreme Layout
Backlit Speakers
Control Panel
FRONT
Backlit Woofer
Backlit Woofer
LEFT SIDE
RIGHT SIDE
Auxiliary Power Out 12V Power In SAE SAE Connector (Black) Connector (Red)
Light Bar
3.) Properly clean the ECOXGEAR and ensure the gaskets have no sand, dirt, or
water on them prior to storage. 4.) Store your unit with all caps properly
sealed to avoid long term internal moisture damage inside your unit. 5.)
Return the ECOXGEAR to Grace Digital if you suspect water ingress into the
unit or if the unit has experienced a severe
impact that may have affected the integrity of the unit to take on water. You
should never
1.) Never power your ECOXGEAR if you suspect water has entered the device.
Powering a device with water inside could be potentially hazardous and cause
fire or a spark.
2.) Never use your ECOXGEAR if you have dropped it or thrown it against a hard
surface which may have destroyed the integrity of the speaker, housing, or
gaskets. In the event of a severe impact to your unit, please return the unit
to Grace Digital to review for potential damage.
3.) Never open the auxiliary doors in a water environment. This could cause
water to ingress into the unit which could potentially be hazardous and cause
a fire or a spark.
4.) Never connect a device to the auxiliary input jacks when in a water
environment. The auxiliary jacks should only be used in a dry environment.
5.) Never attempt to fix, repair your ECOXGEAR unit. Please send it back to
Grace Digital for any assessments and repairs.
CARE, MAINTENANCE & PRECAUTIONS:
1.) The unit is waterproof only when the caps and door are properly closed.
2.) Close the caps and door properly before use. If the unit is placed in a
water environment without the caps or door properly
closed, water may enter into the unit and void your warranty. 3.) Dry unit
completely before opening the caps. Do NOT open the caps if wet or in a wet
environment. 4.) Do NOT apply excessive force to any surfaces of the unit when
wet or in a wet environment. 5.) Do NOT use or store the unit in places with
high temperature. 6.) AVOID prolonged exposure to ultraviolet radiation (UV
sunlight) and strong magnetic fields. 7.) Periodically check the rubber seal
on the caps and door for premature wear. 8.) Periodically clean the rubber
with a soft moist cloth and ensure no objects such as dirt, hair, sand are on
the rubber seal
ring. Do NOT use any oily solvent or chemicals for cleaning. 9.) Rinse off the
unit with tap water after use in salt water. 10.) Power the unit by attaching
the 12V Power In SAE Connector to the 30″ Power Cable intended for use with
the unit.
The unit must be connected to a 12VDC power source. If the battery terminal
voltage is not 12V, you will need a DCDC converter with output 12V.
Connecting the unit to a non-12VDC power source will lead to a malfunction or
damage to the unit.
LIMITED MANUFACTURER’S WARRANTY:
SoundExtreme is covered by a 1-year limited warranty that covers defects in
workmanship and / or materials for a period of 1 year from original purchase
date. This warranty does not apply to any products which have been abused,
neglected, modified or used for a purpose other than the one for which they
were manufactured. Please refer to the above care and maintenance instructions
for suggested care details. The warranty is valid only for the original owner
who purchases the unit from an authorized dealer. Transfers do not qualify for
warranty protection. Grace Digital reserves the right to replace any out-of-
stock or discontinued product with a comparable product. Discontinued products
may not be available for warranty replacement. Any contents are NOT covered by
the limited manufacturer’s warranty. Warranty terms may be revised without
notification at the discretion of the manufacturer. Please visit
www.ecoxgear.com for additional product & warranty information.
SoundExtreme SE26 by ECOXGEAR, a division of Grace Digital Inc., San Diego,
California. Designed in California. Made in China.
This product is protected under patent US 9,307,307 B2 and several patents
pending.
BACK
2
19
FCC STATEMENT:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1.) This device may not cause harmful interference, and
2.) This device must accept any interference received, including interference
that may cause undesired operation.
WARNING: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment. NOTE: To maintain compliance with FCC’s RF Exposure guidelines,
this equipment should be installed and operated with minimum distance between
20cm the radiator to your body: Use only the supplied antenna. FCC ID: 2AAUI-
GDIEXSNDXTR01.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: reorient or relocate the receiving antenna,
increase the separation between the equipment and receiver, connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected, consult the dealer or an experienced radio/TV
technician for help.
RF WARNING STATEMENT:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
IC STATEMENT:
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
1.) This device may not cause interference, and
2.) This device must accept any interference, including interference that may
cause undesired operation of the device.
PRODUCT USE AND PROTECTION:
Read and follow all instructions. Use only as intended.
The ECOXGEAR Bluetooth speaker is intended to be used indoors or outdoors and
in land or water environments. The speaker has been tested to IP66
waterproofing standards, which means the speaker can be exposed to dust and
water, but should not be submerged underwater. The speaker is NOT intended for
constant underwater use.
Always make sure the cap(s) / cover(s) are clean, free from sand or debris,
and correctly fitted. The speaker will only meet IP66 ratings if all rubber
seals, gasket(s) and cover(s) / cap(s) are in place. If you notice a muffling
of audio after submersion, gently shake the unit to clear excess water. If
your speaker is exposed to salt water, clean it thoroughly after use with
fresh water.
To prevent fire or shock, do NOT attempt to power this unit if it is wet or
you suspect water has entered the unit. In this situation, please return the
unit to Grace Digital for a free assessment. If we have found that the unit
has carried water, we will repair or replace the unit free of charge.
SAFETY ADVISORY & WARNING:
Read and follow all instructions. Use only as intended.
CAUTION: Do NOT open to repair. A qualified technician must carry out repair
work.
ATTENTION: Do NOT connect to a 12VDC power supply while the unit is wet. Make
sure all connections are dry BEFORE connecting to a power source. Failure to
do so may result in electrical damage to the unit and may void the warranty.
WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov
WARNING: Danger of explosion if battery is incorrectly replaced.
ATTENTION: Do NOT dispose of in a landfill. Contact Grace Digital at
www.gracesupport.com or a certified recycling agent to dispose of the unit.
SAFETY:
This product has a limited life span of use and should be replaced when it
shows obvious signs of wear.
Do not modify or remove any original component parts of the speaker. Doing so
could cause damage to the unit, allowing water to ingress. A unit with water
ingress should not be charged due to potential risk of fire or shock.
Please exercise care and good judgment when using your ECOXGEAR speaker. Audio
levels should be appropriate to your environment, comply with all local
regulations, and always ensure that you can hear and be aware of any potential
hazards around you.
You should always
1.) Use the ECOXGEAR speaker in accordance with any music or noise rules and
regulations.
2.) Properly seal the ECOXGEAR prior and after each use when in humid or water
environments to avoid water damage to the internal components. Salt water /
air is particularly corrosive. Always make sure that the gaskets are sealed
when in a salt water environment and that the unit is properly rinsed off
after use.
18
In/Out Connections
USB Charging AUX-IN
Port
Port (Black)
AUX-OUT Port (Gray)
Do NOT use these connections if they are wet.
AUX-IN: This input can be used to connect a CD player, MP3 player, etc.
AUX-OUT: This output can be used to connect to an amplifier or to another
speaker AUX-IN connection.
USB Charging Port: Connect your device’s charge cable here to charge it. USB
charging only functions when the SoundExtreme’s power is turned on. USB port
rating is 5V, 2.1A.
Important: Maintaining Waterproofness
If the caps on the control panel, the AUX-IN, and AUX-OUT Ports are not
properly closed, the unit is NOT watertight.
To close the USB Charging Out Port properly, push firmly to be sure the cap
fits flat along the edges with the panel.
To close the AUX-IN and AUX-OUT ports properly, push firmly to be sure the cap
snaps securely into place.
3
Connecting to 12VDC Power Supply
The SoundExtreme does not have an internal battery. It must be connected to an
external 12VDC power supply to function. When you install the SoundExtreme to
a battery or a voltage regulator on a golf cart, a boat, a quad bike, a UTV,
or another vehicle, you need to make sure that your vehicle battery or battery
pack terminal voltage is 12VDC. If the battery terminal voltage is not 12V,
you will need a DCDC converter with output 12V. Connecting the SoundExtreme
to a non-12VDC power source will lead to a malfunction or damage to the
speaker. WARNING: Even when powered off, the SoundExtreme will draw a small
amount of power from your battery. To prevent draining your battery when your
SoundExtreme or powersports vehicle are not in use for more than 48hrs, we
suggest unplugging the SoundExtreme from the battery or adding the toggle
switch. (Toggle switch sold separately.)
Attach the 8ft Power Cable to the 12V Power In SAE Connector (RED). Use
Caution: Do NOT connect to 12V Battery if the Power In SAE Connector is wet.
Contact may cause electric shock and injury if wet.
Remove the 15 Amp Blade Fuse from the Fuse Holder. Use Caution: Do NOT remove
Fuse if the Fuse Holder is wet. An improperly fitted cap may cause electric
shock and injury if wet. To close properly, push firmly to be sure the cap
snaps into place. 4
Specifications
Dimensions
4.5 in / 114.3 mm
4.5 in / 114.3 mm
25.5 in / 647.7 mm
Unit + Mounts Height 5.75 in
Unit Weight 11 lbs
Bluetooth Compliance Bluetooth V 5.0
Bluetooth Frequency Band 2.402~2.480GHz ISM Spectrum
Modulation GFSK, /4-DQPSK, 8DPSK
Bluetooth Range Up to 100 ft / 30m
Tweeter (2x) 1” (25.4 mm) tweeter
Woofer (2x) 4” (101.6 mm) woofer
Mid-Range Speaker (4x) 2.25” (57.15mm) speaker
Audio Output Power 500W (peak)
Power Supply Input Voltage: 12VDC, 10A (requires connection to external DC
battery for power)
USB Output 5V, 2.1A EcoCast Using Qualcomm® Broadcast Audio technology EcoCast
Range 30 ft / 9.1 m between Casting speaker and Receiving speakers
Compatibility Mobile phone / device supporting Bluetooth V1.1 (and above)
Radio Frequency Range US: FM 87.5 – 107.9 mHz RF Remote Operating Frequency
433 MHz Blade Fuse 15A, 32V Storage Temperature -40°F to 122°F / -40°C to 50°C
Operating Temperature 23°F to 95°F / -5°C to 35°C Waterproof / Dust Rating
IP66
17
Troubleshooting
The sound is distorted Try lowering the volume control of your connected
device or musical instrument. Also, try to reduce the overall volume of the
SoundExtreme. Cannot Pair With Bluetooth Device Make sure that your device is
compatible with Bluetooth. Turn off your SoundExtreme and Bluetooth device,
then power on and reconnect. Make sure that Bluetooth mode is selected on your
SoundExtreme. If there is poor FM reception To adjust FM reception, move
entire product. Can NOT play music from a flash drive The USB ports are only
for charging USB devices. Volume level is too low Increase the volume on the
SoundExtreme and / or increase the volume on your Bluetooth device. LED lights
for show and off-road use only Check with local ordinance before using LED
lights. Do NOT drive on public roads with LED lights on. LED lights are not
DOT compliant. Please do NOT attempt to fix your SoundExtreme Please contact
our Customer Support at support@gracedigital.com or call us at 866.446.0961.
WARNING: REMOTE CONTROL INCLUDES A BUTTON BATTERY Keep the BUTTON BATTERY out
of reach of CHILDREN. If swallowed, SEEK MEDICAL ATTENTION IMMEDIATELY, as
ingestion may lead to serious injury, chemical burns, or death.
16
Installation: Gas Vehicle
1. Loosen the bolts on the battery terminals.
Use Caution: Do NOT attempt to loosen bolts if battery is wet. Contact may
cause electric shock and injury if wet.
2. Connect the BLACK wire to the BLACK, negative terminal, then the RED wire
to the RED, positive terminal. Unit will not work correctly and may be damaged
if wires are not correctly attached.
3. Tighten the bolts on the battery terminals until the connectors are held
firmly in place.
4. Return the 15 Amp Blade Fuse into the Fuse Holder and close the cap.
Installation: Electric Vehicle
1. Switch your vehicle to TOW mode.
2. Loosen the bolts on the battery terminals.
3. Connect the BLACK wire to the GROUND on the DC-DC Converter, then the RED
wire to the POSITIVE (+) post on the DC-DC Converter. Unit will not work
correctly and may be damaged if wires are not correctly attached.
4. Tighten the bolts on the battery terminals until the connectors are held
firmly in place.
5. Return the 15 Amp Blade Fuse into the Fuse Holder and close the cap.
Tip: Use zip ties to gather any excess wires, and secure them so that they are
not dangling, loosely.
Loosen Bolts Black Cable Red Cable
Tighten Bolts
5
Controls
Mounting Your Speaker
1. LED Indicators: Each of the 4 LEDs
correspond to different functions:
1
Power, Bluetooth, Mode, and Status.
2
3
2. Power Button: Press button to
turn the SoundExtreme on / off.
4
3. Mode Button: Press button to
5
cycle through the following modes:
Bluetooth, EcoCast Transmitting,
6
7
EcoCast Receiving, FM, and AUX-IN.
8
9
4. Volume Control Buttons: Press
to adjust the speaker’s volume.
Press and hold to adjust the
volume continually.
5. Track Buttons: Press buttons to go to the previous / next track on a paired Bluetooth device.
CONTROL PANEL
6. Backlight Speakers Button: Press to cycle through the following 6 Party Light Modes: Green Light, Red Light, White Light, Blue Light, Music Sync, and Fading.
7. Light Bar Button: Press to cycle through the following 5 Light Modes: Red Light, Yellow Light, White Light (High), White Light (Mid), and White Light (Low). Press and hold to enable / disable Accessory Mode (which turns on /off the Auxiliary Power Out connection).
8. Bluetooth Button: When in Bluetooth Mode, if the Bluetooth LED Indicator is not flashing Blue, press this button to enter Bluetooth Pairing mode. If your device is paired (solid Blue LED), press button to disconnect. Press and hold this button for 5 seconds to clear all pairing records. In FM Mode, this button is used for FM Station Preset 1.
1. To mount the speaker, first place the 2 Mounts on the ends of the
SoundExtreme at your desired orientation and attach them using three or four
(depending on the orientation of your mount) Button Head Bolts, each. Tighten
securely.
2. Ensure that the speaker fits in the desired location and mark where the
mounts will be attached to your vehicle.
3. Drill holes at the desired mounting points on your vehicle, large enough
for the provided ¼-20 Bolts to fit.
4. Place the Rubber Feet on both Mounts.
5. Attach the Mounts to your vehicle with the provided ¼-20 Bolts and Nuts.
Tighten securely.
Tip: Alternatively to drilling holes into your vehicle, you can also use the
provided Worm Clamps to secure the speaker to your vehicle. In order to
prevent scratching /damage to your vehicle, slide the provided rubber sleeves
onto the worm clamps before securing the speaker.
9. Play / Pause / Answer / EcoTalk Button: Press to play / pause a track or answer / end a mobile call from a paired Bluetooth device. Press and hold to activate your Voice Assistant (Siri and OK Google). In FM Mode, this button is used for FM Station Preset 2.
Note: For high-speed, high-vibration, and high-impact applications, we recommend using the provided ¼-20 Bolt mounting solution, detailed above.
6
15
After the SoundExtreme is connected to your Bluetooth device, press briefly to play, press again to pause.
Press briefly to play previous song. Press next song.
briefly to get the
Press or briefly to adjust the speaker volume.
LED: Backlit Speakers
Press
briefly to turn on your speaker backlights.
Press or briefly to cycle through the 6 Party Light modes.
LED: Light Bar
Press
briefly to turn on your Light Bar.
Press or briefly to cycle through the 5 Light modes.
Remote Switch
First, connect your accessory to the Auxiliary Power Out SAE Connector (12V only).
Press
briefly to enable Auxiliary Power Out. The speaker will
announce, “Accessory mode enabled.”
Press
again to disable Auxiliary Power Out. The speaker will
announce, “Accessory mode disabled.”
Use Caution: Do NOT connect to your accessory if the Auxiliary Power Out SAE Connector is wet. Contact may cause electric shock and injury if wet.
14
Operations
LED Indicators
From left to right, the 4 LED Indicators correspond to Power, Bluetooth, Mode,
and Status. 1. Power
Solid Green: Power On No Light: Power Off 2. Bluetooth Flashing Blue:
Bluetooth Paring Solid Blue: Bluetooth Connected 3. Mode Solid Blue: Speaker
Mode Solid / Flashing Red: EcoCast Transmitting Mode Solid / Flashing Green:
EcoCast Receiving Mode 4. Status Solid Blue: FM Solid Green: AUX-IN Solid Red:
Accessory Mode Enabled
Power On / Off
Power On: Press briefly to power on the SoundExtreme. “Speaker on, ready to
connect” voice prompt will be heard. Power Off: Press briefly to power off the
SoundExtreme.
Mode Button
Press briefly to cycle through the following modes: Bluetooth, EcoCast
Transmitting, EcoCast Receiving, FM, and AUX-IN.
7
Pairing a Bluetooth Device
1. Turn on your Bluetooth device. 2. Power on SoundExtreme. “Speaker on,
ready to connect” voice
prompt will be heard. If the Bluetooth LED Indicator (the second LED Indicator
from the left) is not flashing, briefly press to start pairing your device. 3.
Navigate to your Bluetooth device’s setup screen, find ECOXGEAR and connect.
If the connection is successful, the Bluetooth icon will be lit solid and your
SoundExtreme will announce “Your phone is connected.” Notes: · If the pairing
is not complete within 5 minutes, the speaker will exit the pairing mode. You
need to repeat the pairing steps again. · After the connection is successful,
if you turn the speaker off and turn it on again, it will reconnect to the
last connected device automatically. Also, a voice prompt, “Speaker on, ready
to connect” followed by, “Your phone is connected” will be heard. · PRESS AND
HOLD for 5 seconds to clear all pairing records.
Adjust Volume
1. Press or briefly to adjust the speaker volume. 2. PRESS AND HOLD or to
adjust the volume continuously.
a. Press briefly to increase one volume level. PRESS AND HOLD to keep
increasing the volume until maximum volume level is reached.
b. Press briefly to decrease one volume level. PRESS AND HOLD to keep
decreasing the volume until minimum volume level is reached.
8
Remote Control
Pairing Your Remote Control
Before you use your Remote Control for the first time, pull and remove the plastic tab at the bottom of the Remote Control. Your Remote Control should be paired to your unit. IF NOT paired, please follow the steps below.
1. Connect the SoundExtreme to a 12V power supply. (Refer to Connecting to 12VDC Power Supply for details.)
2. Within 15 seconds, PRESS AND
HOLD
for 3 seconds. Your
Remote Control will be paired with
your SoundExtreme.
3. Verify that your remote control
works by pressing the
to see
if the speakers light up.
REMOTE CONTROL
If the speakers do not light up, unplug the 12V power supply, then repeat the above steps.
Once the remote is paired with the SoundExtreme, it will remain stored in the SoundExtreme’s memory and should not need to be paired again.
Audio
Power On: PRESS AND HOLD for 3 seconds to power on the SoundExtreme. “Speaker
on, ready to connect” voice prompt will be heard.
Power Off: PRESS AND HOLD for 3 seconds to power off the SoundExtreme.
Press briefly to cycle through the following modes: Bluetooth, EcoCast
Transmitting, EcoCast Receiving, FM, and AUX-IN.
13
Listening to FM Radio (FM Mode)
Press briefly to cycle through to FM Mode. Press or briefly to tune in a radio
station. To “seek” (jump to the next available station), PRESS AND HOLD either
button down for a few seconds until it starts to seek a station.
When you tune and listen to a station, you can PRESS AND HOLD to assign the
current station to Preset 1, or PRESS AND HOLD to assign the current station
to Preset 2.
If you want to listen to a stored preset, briefly press either button to go to
the stored radio station.
Party Lights
Press
briefly to cycle through 6 Party Light Modes: Green Light,
Red Light, White Light, Blue Light, Music Sync, and Fading.
Press
briefly to cycle through 5 Light Modes: Red Light, Yellow
Light, White Light (High), White Light (Mid), White Light (Low).
Accessory Mode
First, connect your accessory to the Auxiliary Power Out SAE Connector (12V only).
PRESS AND HOLD
for 3 seconds to enable Auxiliary Power Out.
The speaker will announce, “Accessory mode enabled.”
PRESS AND HOLD
again to disable Auxiliary Power Out. The
speaker will announce, “Accessory mode disabled.”
Use Caution: Do NOT connect to your accessory if the Auxiliary Power Out SAE Connector is wet. Contact may cause electric shock and injury if wet.
12
Play Music (Bluetooth Mode)
After the SoundExtreme is connected to your Bluetooth device, press briefly on
the SoundExtreme to play, press again to pause. Press briefly to play previous
song. Press briefly to get the next song. Notes: · Pair and connect your
Bluetooth device with SoundExtreme
before using this feature. · If a call is received when you are listening to
music, press briefly
on the SoundExtreme to answer the call. Press again to end the call. · You can
also control Volume and Play / Pause music operations from your Bluetooth
enabled device. When the Audio Source is via the AUX-In connection, you must
use your device to control Play / Pause music operations.
EcoTalk
PRESS AND HOLD for 3 seconds to activate the voice assistant on your device
(Siri, OK Google, etc.). Once activated, the speakerphone mic on your
SoundExtreme will hear your voice commands and transfer them to the voice
assistant on your device. Notes: · Before using the EcoTalk function, your
device must be connected to
the SoundExtreme via Bluetooth. · Not all devices have voice assistant
functionality; refer to your device
for details.
9
EcoCast Broadcast Your Music to Multiple Speakers
x100
When you have two or more SoundExtreme speakers, you can build a broadcast
system by initiating EcoCast Transmitting Mode in one SoundExtreme speaker and
broadcasting your music to one or more SoundExtreme speakers in EcoCast
Receiving Mode.
EcoCast: First Two Speakers
A
B
1. Follow the Pairing a Bluetooth Device instructions to connect one
SoundExtreme (Speaker A) to your Bluetooth device. After your device is
connected to Speaker A, you can select a song to play.
2. Press on Speaker A to initiate EcoCast Transmitting Mode. The Mode LED
Indicator (the third LED Indicator from the left) will flash Red, and the
speaker will announce, “EcoCast transmitting.”
3. Power on Speaker B speaker and press to cycle through to and initiate
EcoCast Receiving Mode. The Mode LED Indicator will flash Green, and the
speaker will announce, “EcoCast receiving.”
4. Once the connection between the speakers is successful, Speaker B will
announce, “Connection Successful,” and start playing music from your Bluetooth
device.
10
EcoCast: Additional Receiving Speakers A
B C
D
1. Power on the additional SoundExtreme speaker(s) (Speaker C and Speaker D).
Press to cycle through to and initiate EcoCast Receiving Mode. The Mode LED
Indicator will flash Green, and the speaker(s) will announce, “EcoCast
receiving.”
2. On Speaker A (the speaker with the Mode LED Indicator shining solid Red),
PRESS AND HOLD for 6 seconds. The Mode LED Indicator will flash Red.
3. Once the connection between the speakers is successful, Speaker C (and
Speaker D) will announce, “Connection Successful,” and start playing music
from your Bluetooth device.
Notes:
· If all the speakers are turned off, then turned on, the speaker(s) in
EcoCast Receiving Mode (Speakers B, C, and D) will automatically re-connect to
the speaker in Transmitting Mode (Speaker A). If they are not automatically
re-connected, please follow the above steps.
· You can also pair the SoundExtreme with any other ECOXGEAR speaker bearing
the EcoCast symbol .
· The EcoCast functionality is only available while using Bluetooth as your
Audio Source at a maximum range of 30 feet between speakers.
· While connecting the SoundExtreme speakers, make sure that the speakers are
within a few feet of each other.
11
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>