ECOXGEAR GDI-EXESW80 Extreme Sub ES08 Subwoofer User Guide
- June 4, 2024
- Ecoxgear
Table of Contents
- What’s in the Box
- Extreme Sub Layout
- In/Out Connections
- Connecting to 12VDC Power Supply
- Installation: Electric Vehicle
- Controls
- Operations
- Phase Button
- Aux-In Audio Connection
- Remote Gain Level Controller
- Important: Maintaining Waterproofness
- Mounting Your Subwoofer
- Troubleshooting
- **Specifications
- FCC STATEMENT:
- SAFETY ADVISORY & WARNING:
- CARE, MAINTENANCE & PRECAUTIONS:
- LIMITED MANUFACTURER’S WARRANTY:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
GDI-EXESW80 Extreme Sub ES08 Subwoofer
User Guide
Extreme Sub ES08
Models: GDI-EXESW80
POWERSPORTS + GOLF CARS + MARINE
SUBWOOFER
What’s in the Box
Extreme Sub Layout
In/Out Connections
Do NOT use these connections if they are wet.
Aux-In / Sub-In Jack: If you do not want to connect the Extreme Sub
wirelessly via EcoCast or want to connect it to a non-ECOXGEAR amplifier or
speaker, you can connect the subwoofer using this input and the supplied 3.5mm
Audio Cable. Connect it to any brand of stereo, amplifier, or soundbar’s wired
subwoofer-out or line-out.
Remote Gain Level Control Jack: This input can be connected to the
supplied Remote Gain Level Controller, which allows for easy adjustment of the
Extreme Sub’s overall output.
Remote Turn-On Jack: This input can be used to turn on or turn off the
Extreme Sub by another device. When the Auto-Turn-On Switch is turned to
“Remote,” a 12VDC signal will turn on the Extreme Sub. A (Dark Blue) Remote
Turn-On Cable has been provided for your convenience.
12V Power-In Connector: This connector is used to connect to an external
12VDC power supply, with a minimum of a 30A current rating, via the supplied
6.6ft Power Cable (EC5, female).
Connecting to 12VDC Power Supply
The Extreme Sub does not have an internal battery. It must be connected to an external 12VDC power supply to function. Before you connect the Extreme Sub to a battery or a voltage regulator on a golf cart, a boat, a quad bike, a UTV, or another vehicle, you need to confirm the following:
- Your vehicle battery or battery pack’s terminal voltage is 12VDC.
- Your vehicle battery or battery pack can supply a 30A current rating to the Extreme Sub.
If both an Extreme Sub and an ECOXGEAR SoundExtreme soundbar are connected to
the same battery or battery pack, it requires a 40A current rating supply. So,
before connecting to the vehicle’s power supply, please check your vehicle’s
electrical specifications, or consult with the vehicle’s manufacturer or
distributor.
If the battery terminal voltage is not 12V, it requires a DC-DC converter with
output 12V and 30A or 40A rating, as explained above.
Connecting the Extreme Sub to a non-12VDC power source will lead to a
malfunction or damage to the subwoofer.
On electric vehicles, a DC-DC converter is required to avoid damage to the
unit and the vehicle.
The accessory power output on the SoundExtreme soundbar (sold separately) does
not have enough current capacity to supply the Extreme Sub. Do NOT connect the
Extreme Sub Power-In Connector to the SoundExtreme accessory power output.
WARNING: In certain power modes, the Extreme Sub will still draw power
when it is off. To avoid battery drain, connect the supplied Remote Turn-On
Cable (Dark Blue)
to power, the on/off switch or disconnect the subwoofer from the power source
when storing for long periods of time.
Installation: Gas Vehicle
-
Loosen the nuts on the battery terminals.
Use Caution: Do NOT attempt to loosen nuts if the battery is wet. Contact may cause electric shock and injury if wet. -
Connect the BLACK wire to the BLACK, negative terminal.
-
Connect the RED wire to the RED, positive terminal. The unit will not work correctly and may be damaged if wires are not correctly attached.
-
Tighten the nuts on the battery terminals until the connectors are held firmly in place.
-
Connect the (EC5) female connector on the 6.6ft Power Cable to the (EC5) male 12VDC Power-In Connector.
Use Caution: Do NOT connect to 12V Battery if the 6.6ft Power Cable or the (EC5) Power-In Connector are wet. Contact may cause electric shock and injury if wet. -
Turn the Auto-Turn-On Switch toward, “DC” in order to turn on the subwoofer.
Tip: Use zip ties to gather any excess wires, and secure them so that they are not dangling, loosely.
Installation: Electric Vehicle
-
Switch your vehicle to TOW mode.
-
Wire the BLACK wire on the Extreme Sub-power cable to the GROUND on the output of the DC-DC Converter.
-
Wire the RED wire on the Extreme Sub to the POSITIVE (+) post on the output of the DC-DC converter. The unit will not work correctly and may be damaged if wires are not correctly attached.
-
Connect the (EC5) female connector on the 6.6ft Power Cable to the (EC5) male 12VDC Power-In Connector. Use Caution: Do NOT connect to the DC-DC converter if the 6.6ft Power Cable or the (EC5) Power-In Connector are wet. Contact may cause electric shock and injury if wet.
-
Turn the Auto-Turn-On Switch toward, “DC” in order to turn on the subwoofer.
Tip: Use zip ties to gather any excess wires, and secure them so that they are not dangling, loosely.
Controls
- LED Indicators: Each of the 2 LEDs corresponds to different functions: AUX, Phase, and EcoCast Receiving.
- Phase Button: Press this button to toggle the Extreme Sub sound output from the in-phase to the out-of-phase. If the AUX LED flashes Green 3 times, the sound output is in phase. If the AUX LED flashes Red 3 times, the sound output is out of phase.
- EcoCast Button: When turned on, the Extreme Sub enters EcoCast Receiving Mode. If it is not paired with a SoundExtreme, press this button to put the Extreme Sub into Pairing Mode.
- Party Lights Button: Press to cycle through the following 12 Party Light Modes: Red, Orange, Yellow, Green, Cyan, Blue, Purple, White, Music Sync, FADE7, JUMP7, and Color Fade. Press and hold to turn off the Party Lights.
- Gain Control Buttons: Press to increase or decrease the gain level of the Extreme Sub. The Gain Controls allow you to change the relative value of the Extreme Sub compared to the SoundExtreme.
- Crossover Control Buttons: Press to decrease or increase the frequency range of the Extreme Sub. Reducing the Crossover Frequency will result in the Extreme Sub performing solely as a low-frequency subwoofer.
- Auto-Turn-On Switch: Turn the switch to select one of three modes: Remote, Audio, and DC.
Operations
Auto-Turn-On Switch Turn the Auto-Turn-On Switch to select
one of three modes: Remote, Audio, and DC.
Remote: When the switch is turned to this position, the (Dark Blue)
Remote Turn-On Cable must be connected to the vehicle ignition switch or the
vehicle’s 12VDC power
supply. When the vehicle’s ignition is on or the Remote Turn-On Cable has a
12VDC signal, the Extreme Sub will turn on.
Audio : When the switch is turned to this position, the Aux-In / Sub-In
Jack must have an Aux-In audio input connection from a soundbar, an amplifier,
or stereo receivers. The Extreme Sub will turn on only when there is an audio
signal input.
DC: When the switch is turned to this position, the Extreme Sub will turn
on whenever there is a 12VDC power supply.
LED Indicators
There are two LED Indicators at the top of the Control Panel. The left LED
indicator corresponds to AUX and Phase, and the right LED Indicator
corresponds to EcoCast Receiving.
1. AUX
Solid Blue: When an Aux-In cable is plugged in Phase – Sound Output When the
Phase Button has been pressed, the AUX LED flashes 3 times to indicate if the
Extreme Sub sound output is in or out of phase.
Flashing Green : Sound output is in phase
Flashing Red: Sound output is out of phase
2. ECOCAST
Flashing Green: EcoCast Receiving Mode – Pairing
Solid Green: EcoCast Receiving Mode – Paired
Phase Button
Press PHASE briefly to toggle the Extreme Sub sound output from in-phase to
out-of-phase. If the AUX LED flashes Green 3 times, the sound output is in
phase. If the AUX LED flashes Red 3 times, the sound output is out of phase.
Note: Pairing multiple subwoofers, depending on their location to one another,
can result in the subwoofers sounding out of phase with each other and a
reduction in their overall, perceived volume output. Toggle the PHASE button
to determine which setting provides the optimal bass performance.
Adjust Gain
Press – briefly to reduce the gain. Press = briefly to increase the gain.
The LEDs between the Gain Control Buttons indicate the gain level. When
increased, the LEDs will light up, towards the right. When decreased, the LEDs
will turn off, towards the left.
Notes:
- When you adjust the volume level on your connected ECOXGEAR SoundExtreme soundbar, the volume level will adjust automatically on the Extreme Sub. The gain controls allow you to change the relative value of the subwoofer compared to the soundbar.
- The Gain Control Buttons control the sensitivity of the amplifier built into the subwoofer. You will want to optimize the gain level of the subwoofer depending on the type of music you enjoy as well as the location of the Extreme Sub.
Adjust Crossover
Press < briefly to reduce the frequency range that the amplifier sends to the
subwoofer. Press > briefly to increase the frequency range. The LEDs between
the Crossover Control Buttons indicate the frequency level. When increased,
the LEDs will light up, towards the right. When decreased, the LEDs will turn
off, towards the left.
Notes:
·When the crossover frequency is set to 275Hz, you receive the full range of
the Extreme Sub’s capability. This allows it to play low woofer frequencies,
not just subwoofer frequencies, to produce a more full sound profile when
paired with ECOXGEAR SoundExtreme soundbars.
·When the crossover frequency is reduced down to 50Hz, the Extreme sub will
perform solely as a low-frequency subwoofer.
Party Lights
Press briefly to cycle through 12 Party Light Modes: Red, Orange, Yellow,
Green, Cyan, Blue, Purple, White, Music Sync, FADE7, JUMP7, Color Fade.
PRESS AND HOLD to turn off the Party Lights.
EcoCast – Broadcast Your Music to Multiple Speakers and Extreme Subs
The ECOXGEAR SoundExtreme speaker is designed to be paired with
one or more SoundExtreme speakers and Extreme Subs. You can build a broadcast
system by initiating EcoCast Transmitting Mode in one SoundExtreme speaker and
broadcasting your music to one or more Extreme Subs and SoundExtreme speakers
in EcoCast Receiving Mode.
Note: The Extreme Sub is always in EcoCast Receiving Mode.
RF Exposure Statement:
The distance between the user and the products should be no less than 20cm.
EcoCast: SoundExtreme to Extreme Sub
- Follow the Pairing Bluetooth Device instructions in your SoundExtreme user guide to connect one SoundExtreme (Speaker A) to your Bluetooth device. After your device is connected to Speaker A, you can select a song to play.
- Press
**MODE**
on Speaker A to initiate EcoCast Transmitting Mode. The Mode LED Indicator (the third LED Indicator from the left) will flash Red, and the speaker will announce, “EcoCast transmitting.” - Power on your Extreme Sub (Sub B). It will already be in EcoCast Receiving Mode. The subwoofer will announce, “EcoCast receiving.”
- Once the connection between the speakers is successful, Sub B will announce, “Connection Successful,” and start playing music from your Bluetooth device.
EcoCast: Additional Receiving Speakers and/or Subwoofers
- Power on the additional SoundExtreme speaker(s) (Speaker C and Sub D). Press
**MODE**
on Speaker C to cycle through to and initiate EcoCast Receiving Mode. The Mode LED Indicator will flash Green, and the speaker(s) will announce, “EcoCast receiving.” - On Speaker A (the speaker with the Mode LED Indicator shining solid Red), PRESS AND HOLD for 6 seconds. The Mode LED Indicator will flash Red.
- Once the connection between the speakers is successful, Speaker C (and Sub D) will announce, “Connection Successful,” and start playing music from your Bluetooth device.
Notes:
-
If all the speakers are turned off, then turned on, the speaker(s) and sub(s) in EcoCast Receiving Mode (Speakers and Subs B, C, and D) will automatically re-connect to the speaker in Transmitting Mode (Speaker A). If they are not automatically re-connected, please follow the above steps. To clear pairing records on an Extreme Sub, PRESS
AND HOLD for 6 seconds. -
You can also pair the SoundExtreme with any other ECOXGEAR speaker bearing the EcoCast symbol ****
-
The EcoCast functionality is only available while using Bluetooth as your Audio Source at a maximum range of 30 feet between speakers.
-
While connecting the SoundExtreme speakers, make sure that the speakers are within a few feet of each other.
-
If you do not want to connect the subwoofer wirelessly or want to connect it to a non-ECOXGEAR amplifier or speaker, you can connect the subwoofer via its Aux-In / Sub-In Jack, using the supplied 3.5mm Audio Cable.
Aux-In Audio Connection
To use an Aux-In audio source, connect the audio output from the source unit
to the Extreme Sub’s Aux-In / Sub-In Jack with the supplied 3.5 Audio Cable.
Once the 3.5mm Audio Cable is plugged in, the Aux-In LED Indicator will shine
solid Blue.
Remote Gain Level Controller
-
Mount the Remote Gain Level Controller in an accessible location. Keep the cable away from the vehicle’s electrical wiring to avoid possible interference from the vehicle’s electrical system.
-
Connect the Remote Gain Level Controller to the (Green) Remote Gain Level Control Jack on the Extreme Sub. The LED on the Remote Gain Level Controller will shine solid Red if the Extreme Sub is turned on.
-
Turn the knob to adjust the gain level.
Important: Maintaining Waterproofness
If the caps on the Aux-In, Remote Gain Level Control, and Remote Turn-On jacks
are not properly closed, the unit is NOT waterproof.
To close the Aux-In, Remote Gain Level Control Connector, and
Remote Turn-On jacks properly, push firmly to be sure the cap snaps securely
into place.
Mounting Your Subwoofer
Use Caution:
-
The Extreme Sub weighs 17 lbs. Please use caution when lifting or handling.
-
The Extreme Sub vibrates when playing heavy bass music at maximum gain. It is important to fasten the subwoofer securely to a flat surface on the vehicle. Whether mounting the subwoofer horizontally or vertically, the supplied Washers and Lock Washers MUST be used.
-
There is a Heat Sink on the back of the Extreme Sub. For optimal performance, install the subwoofer so that the Heat Sink is not in direct sunlight.
Horizontal Mount
-
To mount the subwoofer in a horizontal orientation, first attach the Horizontal Mounting Plate, using eight 29/32” Screws, Lock Washers, and Washers. Tighten securely.
-
Ensure that the subwoofer fits in the desired location and mark where the mounts will be attached to your vehicle.
-
Drill holes at the desired mounting points on your vehicle, large enough for the provided Hex Bolts to fit.
Optional: Place the Mount Standoffs under both ends of the Mounting Plate. Use these optional Standoffs when there is not enough clearance between the Mounting Plate and the vehicle’s mounting surface. -
Attach the Mounting Plate to your vehicle with the provided ¼-20 Hex Bolts, Washers, Lock Washers, and Nuts. Tighten securely.
Troubleshooting
No audio and LED indicator are off
Check if there is the voltage at the Power-In connector or if there is an
ignition signal when the Auto-Turn-On Switch is set to Remote, or if there is
an audio signal input when the Auto-Turn-On Switch is set to Audio.
Poor audio quality
Check if the Gain Level is set properly. Check wires for shorts or grounds.
Check the source signal. Check if the 3.5mm Audio Cable or the Remote Gain
Level Controller cable is close to the vehicle’s electrical wiring.
LED Party Lights for show and off-road use only
Check with the local ordinances before using LED lights. Do NOT drive on
public roads with LED lights on. LED lights are not DOT-compliant.
Please do NOT attempt to fix your Extreme Sub
Please contact our Customer Support at
support@gracedigital.com or call us at
800.903.9524.
**Specifications
**
Unit Dimensions Unit + Horizontal Mount Dimensions
Unit + Horizontal Mount + Mount Standoffs Dimensions
Unit + Vertical Mount Dimensions
Unit Weight
16.87 lbs (7.65 kg)
Horizontal Mount Weight
1.5 lbs (0.68 kg)
Vertical Mounts Weight
1.28 lbs (0.64 lbs x2)
0.58 kg (0.29 kg x2)
Bluetooth Compliance
Bluetooth V 5.0
Bluetooth Frequency Band
2.402~2.480GHz ISM Spectrum
Modulation
GFSK, π/4-DQPSK, 8DPSK
Crossover Range
50Hz – 275Hz
Subwoofer
8” (203.2 mm) subwoofer
Passive Subwoofer
8’’ (203.2 mm) subwoofer
Audio Output Power
500W (peak)
Power Supply
Input Voltage: 12VDC, 30A (requires connection to external DC battery for
power)
EcoCast
Using Qualcomm® Broadcast
Audio technology
EcoCast Range
30 ft / 9.1 m between Casting speaker and Receiving speakers
Blade Fuse
30A, 32V
Storage Temperature
-40°F to 122°F / -40°C to 50°C
Operating Temperature
23°F to 95°F / -5°C to 35°C
Waterproof / Dust Rating
IP66
FCC STATEMENT:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: To maintain compliance with FCC’s RF Exposure guidelines, this
equipment should be installed and operated with a minimum distance between
20cm from the radiator to your body: Use only the supplied antenna.
FCC ID: 2AAUI-GDIEXESW801. This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to Part 15 of
the
FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: reorient or relocate
the receiving antenna, increase the separation between the equipment and
receiver, connect the equipment into an outlet on a circuit different from
that to which the receiver is connected, consult the dealer or an experienced
radio/TV technician for help.
IC STATEMENT:
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
PRODUCT USE AND PROTECTION:
Read and follow all instructions. Use only as intended.
The ECOXGEAR subwoofer is intended to be used indoors or outdoors and in land
or water environments. The subwoofer has been tested to IP66 waterproofing
standards, which means the subwoofer can be exposed to dust and water, but
should not be submerged underwater. The subwoofer is NOT intended for constant
underwater use. Always make sure the cap(s) / cover(s) are clean, free from
sand or debris, and correctly fitted. The subwoofer will only meet IP66
ratings if all rubber seals, gasket(s) and cover(s) / cap(s) are in place. If
you notice the muffling of audio after submersion, gently shake the unit to
clear excess water. If your subwoofer is exposed to salt water, clean it
thoroughly after use with fresh water.
To prevent fire or shock, do NOT attempt to power this unit if it is wet or
you suspect water has entered the unit. In this situation, please return the
unit to Grace Digital for a free assessment. If we have found that the unit
has carried water, we will repair or replace the unit free of charge.
SAFETY ADVISORY & WARNING:
Read and follow all instructions. Use only as intended.
CAUTION: Do NOT open to repair. A qualified technician must carry out
repair work.
ATTENTION: Do NOT connect to a 12VDC power supply while the unit is wet.
Make sure all connections are dry BEFORE connecting to a power source. Failure
to do so may result in electrical damage to the unit and may void the
warranty.
WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov
WARNING: Danger of explosion if the battery is incorrectly replaced.
ATTENTION: Do NOT dispose of in a landfill. Contact Grace Digital at
www.gracesupport.com or a certified recycling
agent to dispose of the unit.
SAFETY:
This product has a limited life span of use and should be replaced when it
shows obvious signs of wear.
Do not modify or remove any original component parts of the subwoofer. Doing
so could cause damage to the unit, allowing water to ingress. A unit with
water ingress should not be charged due to the potential risk of fire or
shock.
Please exercise care and good judgment when using your ECOXGEAR subwoofer.
Audio levels should be appropriate to your environment, comply with all local
regulations, and always ensure that you can hear and be aware of any potential
hazards around you.
You should always
- Use the ECOXGEAR subwoofer in accordance with any music or noise rules and regulations.
- Properly seal the ECOXGEAR prior to and after each use when in humid or water environments to avoid water damage to the internal components. Saltwater/air is particularly corrosive. Always make sure that the gaskets are sealed when in a saltwater environment and that the unit is properly rinsed off after use.
- Properly clean the ECOXGEAR and ensure the gaskets have no sand, dirt, or water on them prior to storage.
- Store your unit with all caps properly sealed to avoid long-term internal moisture damage inside your unit.
- Return the ECOXGEAR to Grace Digital if you suspect water ingress into the unit or if the unit has experienced a severe impact that may have affected the integrity of the unit to take on water.
You should never
- Never power your ECOXGEAR if you suspect water has entered the device. Powering a device with water inside could be potentially hazardous and cause fire or a spark.
- Never use your ECOXGEAR if you have dropped it or thrown it against a hard surface that may have destroyed the integrity of the subwoofer, housing, or gaskets. In the event of a severe impact to your unit, please return the unit to Grace Digital to review for potential damage.
- Never open the auxiliary doors in a water environment. This could cause water to ingress into the unit which could potentially be hazardous and cause a fire or a spark.
- Never connect a device to the auxiliary input jacks when in a water environment. The auxiliary jacks should only be used in a dry environment.
- Never attempt to fix, or repair your ECOXGEAR unit. Please send it back to Grace Digital for any assessments and repairs.
CARE, MAINTENANCE & PRECAUTIONS:
- The unit is waterproof only when the caps and door are properly closed.
- Close the caps and door properly before use. If the unit is placed in a water environment without the caps or door properly closed, water may enter the unit and void your warranty.
- Dry the unit completely before opening the caps. Do NOT open the caps if wet or in a wet environment.
- Do NOT apply excessive force to any surfaces of the unit when wet or in a wet environment.
- Do NOT use or store the unit in places with high temperatures.
- AVOID prolonged exposure to ultraviolet radiation (UV sunlight) and strong magnetic fields.
- Periodically check the rubber seal on the caps and door for premature wear.
- Periodically clean the rubber with a soft moist cloth and ensure no objects such as dirt, hair, or sand are on the rubber seal ring. Do NOT use any oily solvent or chemicals for cleaning.
- Rinse off the unit with tap water after use in salt water.
- Power the unit by attaching the 12VDC Power-In Connector (EC5, male) to the 6.6ft Power Cable (EC5, female) intended for use with the unit. The unit must be connected to a 12VDC, 30A rating power source. If the battery terminal voltage is not 12V, you will need a DC-DC converter with an output of 12V. Connecting the unit to a non-12VDC power source will lead to a malfunction or damage to the unit.
LIMITED MANUFACTURER’S WARRANTY:
Extreme Sub is covered by a 1-year limited warranty that covers defects in
workmanship and/or materials for a period of 1 year from the original purchase
date. This warranty does not apply to any products which have been abused,
neglected, modified or used for a purpose other than the one for which they
were manufactured. Please refer to the above care and maintenance instructions
for suggested care details. The warranty is valid only for the original owner
who purchases the unit from an authorized dealer. Transfers do not qualify for
warranty protection. Grace Digital reserves the right to replace any out-of-
stock or discontinued product with a comparable product. Discontinued products
may not be available for warranty replacement.
Any contents are NOT covered by the limited manufacturer’s warranty. Warranty
terms may be revised without notification at the discretion of the
manufacturer. Please visit www.ecoxgear.com for
additional product & warranty information.
Extreme Sub ES08 by ECOXGEAR, a division
of Grace Digital Inc., San Diego, California.
Designed in California. Made in China.
Patents pending.