MARSON MT581W 2D Ring Wearable Scanner User Guide

June 3, 2024
MARSON

2D Ring
Barcode Scanner
Quick Guide

2D Ring Barcode Scanner Quick Guide (Rev1) P/N: 8013-0069010

REGULATORY INFORMATION

FCC WARNING STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

CANADIAN DOC STATEMENT
This digital apparatus does not exceed the Class B limits for radio noise for digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
CE MARKING AND EUROPEAN UNION COMPLIANCE
Testing for compliance to CE requirements was performed by an independent laboratory. The unit under test was found compliant with all the applicable Directives, 2004/108/EC and 2006/95/EC.
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT
The WEEE directive places an obligation on all EU-based manufacturers and importers to take-back electronic products at the end of their useful life.
ROHS STATEMENT OF COMPLIANCE
This product is compliant to Directive 2002/95/EC.
NON-MODIFICATION STATEMENT
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

WARNING AND CAUTION

| 1. Take any metals into contact with the terminals in connectors.
2. Use the scanner where any inflammable gases.
---|---
| If following condition occur, immediately power off the host computer, disconnect the interface cable, and contact your nearest dealer.
1. Smoke, abnormal odors or noises come from the scanner.
2. Drop the scanner so as to affect the operation or damage its housing.
| Do not do behavior below.
1. Put the scanner in places excessively high temperatures such as expose under direct sunlight.
2. Use the scanner in extremely humid area or drastic temperature changes.
3. Place the scanner in oily smoke or steam environment such as cooking range.
4. Be covered or wrapped up the scanner in bad-ventilated area such as under cloth or blanket.
5. Insert or drop foreign materials or water into scanning window or vents.
6. Using the scanner while hand is wet or damp.
7 . Use the scanner with anti-slip gloves containing plasticizer and chemicals or organic solvents such as benzene, thinner, insecticide etc to clean the housing. Otherwise, it could not result fire and  electrical shock but housing may be broken and injured.
8. Scratch or modify the scanner and bend, twist, pull or heat its interface cable.
9. Put heavy objects on interface cable.
Do not stare the light source from the scanning window or do not point the scanning window at other people’s eyes or eyesight may be damaged by direct exposure under the light.
| Do not put the scanner on an unstable or inclined plane.
The scanner may drop, creating injuries.
| Once the interface cable is damaged such as exposed or broken copper wires, stop using immediately and contact your dealer. Otherwise, it could result fire or electrical shock.

OUT OF THE BOX

INTRODUCTION

BUTTON PREFERENCE

Pressing on Funtion Button allows user to quickly configure preference for Touch-Activated Trigger Button, with the change of LED indicator color representing different configurations:

Red = Enable Left Button Only (Right-handed User)
Blue = Enable Right Button Only (Left-handed User)
Purple = Enable Both Buttons

Clench your fist and use your thumb to tap the touch-activated trigger button. A gentle touch on the button will work; there is no need to press with force.

ATTENTION

  1. It is recommended to dry both your hand and the Velcro strap to avoid the scanner being accidentally triggered by moisture.

  2. The following gloves have been tested to be working with the touch-activated button: latex examination glove antistatic glove, white cotton glove (with or without latex
    coating), safety glove, and rubber glove. However, it is still recommended to operate with bare hand or thin glove to ensure the responsiveness of button.

  3. Don’t need to tighten Velcro strap too much. Just make the strap fit your finger so that the scanner will not easily move while being touched for trigger. We also suggest to release the strap from your finger for 1 minute after 2 hours of continuous use if your finger feels uncomfortable.

BEEPER INDICATION

Single beep
i. Good read on non-configuration barcode
Three beeps Four beeps
ii. Bad read on configuration barcode Good read on configuration barcode Power-up

SPECIFICATIONS

Light source 625nm visible red LED & White LED
Sensor 640 x 480 pixels
Scan rate 60 frames/sec
Resolution 5mil (Code39), 6.67mil (PDF417)
PCS 40%
Width of Field 146mm (13Mil Code39)
Depth of Field  5 Mil Code39: 45 – 145mm

13 Mil UPC/EAN: 65 – 345mm
6.67 Mil PDF417: 55 – 1 20mm
10 Mil DataMatrix: 50 – 1 15mm
15 Mil QR Code: 35 – 165mm
Dimension| W27 .6 x L46.2 x H26.8 mm
Housing| PC+ABS
Connector| Micro
Interface| USB HID, USB VCP
Voltage| 5VDC±5%
Working Current| <  135mA
Standby Current| <  15mA
Operating Temp.|  -20 to 55°C (- 4°F to 131°F)
Storage Temp.|  -40 to 70°C (-40°F to 158°F)
Ambient Light| 100,000 lux
Drop Durability| 1.5M
Sealing| IP42
Symbologies| all major 1D and 2D barcodes

STEP 1: Enter Setup

STEP 2: Scan Desired Setting

READING MODE

MARSON MT581W 2D Ring Wearable Scanner - bar code 2

TERMINATOR

SYMBOLOGIES

KEYBOARD LAYOUT

INTER-CHARACTER DELAY

MARSON MT581W 2D Ring Wearable Scanner - bar code 12

BEEP CONTROL

STEP 3: Exit Setup

Documents / Resources

| MARSON MT581W 2D Ring Wearable Scanner [pdf] User Guide
MT581W, 2D Ring Wearable Scanner, Wearable Scanner, 2D Ring Scanner, Scanner, MT581W
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals