MARSON MT86V Long Range 2D Imager Installation Guide

June 4, 2024
MARSON

MARSON MT86V Long Range 2D Imager

MARSON MT86V Long Range 2D Imager

INTRODUCTION

The MT86V 2D Imager is designed for 1D and 2D barcodes scanning with optimal performance and easy integration. MT86V is ideal for integration into data terminals and mobile devices.

The MT86V 2D Imager consists of 1 illumination LED, 1 Laser aimer and a powerful image sensor that delivers high-quality image to host.

This powerful, reliable mini 2D imager is an ideal choice for a variety of applications, including ticketing, access control, mobile payment and manufacturing.

ELECTRIC INTERFACE

MT86V Long Range 2D Imager Electric Interface

Pin# Name I/O Description Schematic Example
1 GND ———— Power and signal ground. ****
2 GND ———— Power and signal ground. ****
3 VCC_ILLUM Input Supply Power Operating Voltage: 3.3V±5%

Max current: 300mA

4| MDN0| Output| MIPI Data- <0>| ————
5| VCC_ILLUM| Input| Supply Power| Operating Voltage: 3.3V±5%

Max current: 300mA

6| MDP0| Output| MIPI Data+ <0>| ————
7| NC| ————| ————| ————
8| GND| ————| Power and signal ground.|
9| MCLK| I/O| I2C Clock| High = 3.3V, Low = 0V
10| MDN1| Output| MIPI Data- <1>| ————
11| GND| ————| Power and signal ground.|

12| MDP1| Output| MIPI Data+ <1>| ————
13| MDAT| I/O| I2C Data| High = 3.3V, Low = 0V
14| GND| ————| Power and signal ground.| **
15| NC| ————| ————| ————
16| MCN| Output| MIPI Clock-| ————
17| NRST| Input| Reset signal| ————
18| NC| ————| ————| ————
19| POWER_EN| Input| Reserved|
TBD
20| MCP| Output| MIPI Clock+| ————
21| EXT_ILLUM_EN| Output| Reserved|
Floating
22| GND| ————| Power and signal ground.| **

23| ILLUM_ON| Input| Reserved| TBD
24| NC| ————| ————| ————
25| AIM_ON| Input| Reserved| TBD
26| NC| ————| ————| ————
27| NC| ————| ————| ————
28| GND| ————| Power and signal ground.| **
29| VCC| Input| Aim, Logic and Sensor Power|
Operating Voltage: 3.3V±5%**
30| NC| ————| ————| ————
31| VCC| Input| Aim, Logic and Sensor

Power

| Operating Voltage: 3.3V±5%
32| NC| ————| ————| ————
33| GND| ————| Power and signal ground.|
34| GND| ————| Power and signal ground.|

Illumination & Aimer Control

Slave address = 0x20

Address Register Default Value Descirption
0x0001 illumination 0xA Bit[7:4]:Reserved Bit[3:0] 0x 0 : OFF

0x 1 : minimum brightness
0x A : maximum brightness
0x0002| Aimer| 0x1| Bit[7:1]:Reserved Bit[0] 0x 0 : OFF
0x 1 : Aimer on

SCCS single read trom random location

Illumination & Aimer Control

SCCS single write to random location

Illumination & Aimer Control

Power-up Sequence

Power-up Sequence

Power-down Sequence

Power-down Sequence

DIMENSION

(Unit = mm)

MT86V Long Range 2D Imager Dimensions

SPECIFICATIONS

Optic & Performance

Light Source| 5700K CCT white LED
Aiming| 625nm visible red Laser
Sensor| 1280 x 800 pixels
Resolution| 4mil (Code39), 8mil (QR Code)
Field of View| Horizontal 41°, Vertical 26°
Scan Angle| Pitch Angle ±60° Skew Angle ±45° Roll Angle 360°
Print Contrast Ratio| 30%
Width of Field| 200mm (13Mil Code39)
Guaranteed Depth Of Field
( Environment: 800 lux)| 4 Mil Code39:| 100 ~ 150mm
5 Mil Code39:| 90 ~ 180mm
10 Mil Code39:| 45 ~ 370mm
15 Mil Code39:| 60 ~ 480mm
13 Mil UPC/ EAN:| 55 ~ 400mm
10 Mil QR Code:| 65 ~ 220mm
15 Mil QR Code:| 60 ~ 300mm
6.67 Mil PDF417:| 85 ~ 180mm
10 Mil PDF417:| 70 ~ 250mm
Physical Characteristics
Dimension| W23.5 x L10.7 x H6.8 mm
Weight| 2.4g
Color| Black
Material| PC
Connector| 34pin Board-to-Board Connector (pitch=0.4mm)
Electrical
Operation Voltage| 3.3 ± 0.15 VDC
Working Current| < 220 mA
Standby Current| < 80 mA
Connectivity
Interface| MIPI
User Environment
Operating Temperature| -20°C ~ 60°C
Storage Temperature| -30°C ~ 70°C
Humidity| 0% ~ 95%RH (Non-condensing)
Drop Durability| 1.5M
Ambient Light| 100,000 Lux (Sunlight)
Regulatory
ESD| Functional after 4KV contact, 8KV air discharge
(It requires housing that is designed for ESD protection and stray from electric fields.)
EMC| TBA
Safety Approval| TBA
Environmental| WEEE, RoHS 2.0

SCANNING RANGE

MT86V Long Range 2D Imager Scanner Range

MECHANICAL INTEGRATION

The scan engine is designed specifically for integration into customer’s housing for OEM applications. However, the scan engine’s performance will be adversely affected or permanently damaged when mounted into an unsuitable enclosure.

Warning: The limited warranty is void if the following recommendations are not adhered to when mounting the scan engine.

Electrostatic Discharge Cautions

All scan engines are shipped in ESD protective packaging due to the sensitive nature of the exposed electrical components.

  1. ALWAYS use grounding wrist straps and a grounded work area when unpacking and handling the scan engine.
  2. Mount the scan engine in a housing that is designed for ESD protection and stray electric fields.
Mounting MT86V

First of all, the MT86V should be fixed with tow self-forming screws on the host PCBA. To secure MT86V the maximum thread depth is 3.0 mm and operator must use safe ESD practices when handling and mounting the MT86V:

  1. The thickness of PCBA: 0.8 ~ 1.0 mm
  2. The size of screw hole: 1.6mm dia.
  3. The size of screw: T1.6mm X 3.0 mm
  4. The torque of screwdriver:≦1kg-cm (0.86 lb-in)
Connector Specification

Below is the recommended 34-pin board-to-board connector (P/N: 55909 3474) on the host side.

asc

Window Materials

Following are descriptions of three popular window materials:

  1. Poly-methyl Methacrylic (PMMA)
  2. Allyl Diglycol Carbonate (ADC)
  3. Chemically tempered float glass

Cell Cast Acrylic (ASTM: PMMA)
Cell cast Acrylic, or Poly-methyl Methacrylic is fabricated by casting acrylic between two precision sheet of glass. This material has very good optical quality, but is relatively soft and susceptible to attack by chemicals, mechanical stress and UV light. It is strongly recommended to have acrylic hard-coated  with Polysiloxane to provide abrasion resistance and protection from environmental factors. Acrylic can be laser-cut into odd shapes and ultrasonically welded.

Cell Cast ADC, Allyl Diglycol Carbonate (ASTM: ADC)
Also known as CR-39TM, ADC, a thermal setting plastic widely used for plastic eyeglasses, has excellent chemical and environmental resistance. It also has an inherently moderate surface hardness and therefore does not require hard- coating. This material cannot be ultrasonically welded.

Chemically Tempered Float Glass
Glass is a hard material which provides excellent scratch and abrasion resistance. However, un-annealed glass is brittle. Increased flexibility strength with minimal optical distortion requires chemical tempering. Glass cannot be ultrasonically welded and is difficult to cut into odd shapes.

Property Description
Spectral Transmission 85% minimum from 635 to 690 nanometers
Thickness < 1 mm
Coating Both sides to be anti-reflection coated to provide 1% maximum

reflectivity from 635 to 690 nanometers at nominal window tilt angle. An anti- reflection coating can reduce the light that is reflected back to the host case. Coatings will comply with the hardness adherence requirements of MIL-M-13508.

Window Specifications

MT86V Long Range 2D Imager Scanner Range

Window Specifications for MT86V Integration

Tilt Angle (a)| Minimum Window Size|
Horizontal (h)| Vertical (v)| Thickness (t)|
0| 0| 24 mm| 7 mm| < 1 mm|

Window Care

In the aspect of window, the performance of MT86V will be reduced due to any kind of scratch. Thus, reducing the damage of window, there are few things have to be noticed.

  1. Avoid touching the window as much as possible.
  2. When cleaning the window surface, please use non-abrasive cleaning cloth,and then gently wipe the host window with the cloth that is already sprayed with glass cleaner.

REGULATIONS

The MT86V 2D imager conforms to the following regulations:

  1. Electromagnetic Compliance – TBA
  2. Electromagnetic Interference – TBA
  3. Photobiological Safety – TBA
  4. Environmental Regulations – RoHS 2.0, WEEE

VERSION HISTORY

Rev. Date Description Issued Checked
1.0 2020.07.24 Initial Draft Release Shaw Kenji & Alice
1.1 2022.02.11 Updated VCC_ILLUM, EXT_ILLUM_EN, VCC Added Power-up/down
Sequence Shaw Kenji
1.2 2022.09.07 Removed Scan Rate Shaw Kenji

Marson Technology Co., Ltd.
9F., 108-3, Minquan Rd., Xindian Dist., New Taipei City, Taiwan
TEL: 886-2-2218-1633
FAX: 886-2-2218-6638
E-mail: info@marson.com.tw
Web: www.marson.com.tw

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals