MARSON MT8250 2D Handheld Barcode Scanner User Guide

June 6, 2024
MARSON

MARSON MT8250 2D Handheld Barcode Scanner

FCC WARNING STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following memeasurasu es:

  • TThis his digital apparatus does not exceed the Class B limits for radio noise for digital
  • apparatus set out in the Radio Interference Regulations of the Canadian Department of CommCommunications.
  • Reglement le brouillage radioélectrique édicté par les ministère des Communication du Canada.

CE MACE MARKING AND EUROPEAN UNION COMPLIANCE

Testing for compliance to CE requirements was performed by an independent laboratory. The unit under test was found compliant with all the applicable Directives, 2020004/4/108/EC and 2006/95/EC.

WWASTASTE ELECTRICAL AND ELECTRONIC EQUIPMENT

The WEEE directive places an obligation on all EU-based manufacturers and is Imnportant to take-back electronic products at the end of their useful life.

ROHS STATEMENT OF COMPLIANCE

This product is compliant to Directive 2002/95/EC.

NON-MODIFICATION STATEMENT

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

WARNING AND CAUTION

  1. Take any metals into contact with the terminals in connectors.
  2. Use the scanner where any inflammable gases.
  3. If the following conditions occur, immediately power off the host computer, disconnect the interface cable, and contact your nearest dealer.
  4.  Smoke, abnormal odors, or noises come from the scanner.
  5. Drop the scanner so as to affect the operation or damage its housing.
  6. Do not do the behavior below.
  7. Put the scanner in places with excessively high temperatures such as exposed under direct sunlight.
  8. Use the scanner in extremely humid areas or drastic temperature changes.
  9. Place the scanner in oily smoke or steam environment such as a cooking range.
  10. Be covered or wrapped up the scanner in the bad-ventilated areas such as under cloth or blanket.
  11. Insert or drop foreign materials or water into scanning windows or vents.
  12. Use the scanner while the hand is wet or damp.
  13. Use the scanner with anti-slip gloves containing plasticizer and chemicals or organic solvents such as benzene, thinner, insecticide, etc to clean the housing. Otherwise, it could not result in fire and electrical shock but housing may be broken and injured.
  14. Scratch or modify the scanner and bend, twist, pull, or heat its interface cable.
  15. Put heavy objects on the interface cable.
  16. Do not stare at the light source from the scanning window or do not point the scanning window at other people’s eyes or eyesight may be damaged by direct exposure under the light.
  17. Do not put the scanner on an unstable or inclined plane. The scanner may drop, creating injuries.
  18. Once the interface cable is damaged such as exposed or broken copper wires, stop using immediately and contact your dealer. Otherwise, it could result in fire or electrical shock.

SPECIFICATIONS

DIMENSIONS

SCANNING RANGE

BEEPER INDICATION

  • Single Beep
  • Two beeps
  • Three beeps
  • Good read
  • Successful setup
  • Power up

LED INDICATION

  • Green
  • Good read / Successful setup

GETTING STARTED

  1.  The scanner works as a USB keyboard. Make sure your host device supports a USB keyboard before use.
  2.  Plug the scanner into the USB port of your host device. The scanner will emit three beeps at power-up.
  3.  The OS will automatically install a USB driver for the scanner if it is connected to your host device for the first time. Wait until the installation finishes.
  4. Open Notepad or any application that can accept keyboard input. Try scanning some random barcodes and the barcode data will be displayed.

GENERAL SETTINGS

DEFAULTMARSON MT8250 2D Handheld Barcode Fig5

CHECK VERSIONMARSON MT8250 2D Handheld Barcode Fig4

BEEPER

KEYBOARD LAYOUT

SYMBOLOGIES

UPPER / LOWER CASE

INTERFACE

INVERSE BARCODE

USB TRANSMISSION SPEED

Documents / Resources

| MARSON MT8250 2D Handheld Barcode Scanner [pdf] User Guide
MT8250, 2D Handheld Barcode Scanner
---|---
| MARSON MT8250 2D Handheld Barcode Scanner [pdf] User Guide
MT8250, 2D Handheld Barcode Scanner, MT8250 2D Handheld Barcode Scanner, Handheld Barcode Scanner, Barcode Scanner, Scanner

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals