BATTAT WH1140 Remote Control Recycling Truck User Guide

BATTAT WH1140 Remote Control Recycling Truck

TO START PLAYING

1. Make sure the ON/OFF switch on the truck and remote are on the ON position (Fig. 1 & Fig. 2).
2. Press any button on the truck, as indicated in Fig. 4, then press any button on the remote, as indicated in Fig 3.
3. The truck will automatically go into sleep mode after 30 minutes of inactivity to save power. Wake up by pressing any button on the truck, as indicated in Fig. 4.
4. In case the truck disconnects from the controller, switch the truck and the controller OFF, then switch them back ON again (Fig. 1 & Fig. 2). Continue with step 2.

Troubleshooting

REPLACING TRUCK BATTERIES

REPLACING REMOTE CONTROL BATTERIES

• Frequency bands: 2405MHz-2475MHz
• Maximum radio-frequency power: 5dbm

WARNING

• This toy produces flashes that may trigger epilepsy in sensitised individuals.
• SMALL PARTS – CHOKING HAZARD. Not suitable for children under 3 years.
• CHOKING HAZARD—Small parts. Not for children under 3 years.

Alignment lever

STEERING ALIGNMENT ADJUSTMENT

If the vehicle does not drive in a straight line, adjust the alignment using the alignment lever. If the vehicle drifts to the left, turn the lever towards the “R”. If the vehicle drifts to the right, turn the lever towards the “L”.

Please remove all packaging materials before giving to children.

Please retain this information for future reference.

1. Do not use near seawater or in dirty and dusty environments. For indoor play only.
2. Do not use in the rain or immediately after rainfall.
3. If the truck gets wet, open the battery compartment immediately, remove the batteries, and turn the truck upside down to dry.
4. Always clean and dry the truck and remote after using outdoors to avoid damage.
5. Do not overload the truck’s container. Load with small items such as pieces of paper.
6. The remote’s control distance may be reduced when using indoors.
7. The truck’s remote control may not work after long storage. Follow next steps to restart:
   • Always replace the batteries in the truck with 6 new AA alkaline batteries (Fig. 1).
   • Follow steps 1 and 2 on rst page to start playing.
   • If the truck does not work, put 2 new AA alkaline batteries in the remote (Fig. 2).
   • Follow steps 1 and 2 on rst page to start playing.

BATTERY ADVICE

Requires 6 x AA (1.5V) batteries for the truck (included). Requires 2 x AA (1.5V) batteries for the remote control (not included). Non-rechargeable batteries are not to be recharged. Rechargeable batteries are to be removed from the toy before being charged. Rechargeable batteries are only to be charged under adult supervision. Different types of batteries or new and used batteries are not to be mixed. Only batteries of the same or equivalent type as recommended are to be used. Batteries are to be inserted with the correct polarity. Exhausted batteries are to be removed from the toy.The supply terminals are not to be short-circuited. ATTENTION: When the module’s functions lose performance, follow instructions carefully to install new batteries.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions

1. this device may not cause harmful interference.
2. this device must accept any interference received, including interference that may cause undesired operation.

Warning: changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>