BATTAT AN2864 RC Bumper Cars Tarbosaurus Instruction Manual

May 15, 2024
BATTAT

RC BUMPER CARS: TARBOSAURUS
AUTO TAMPONNEUSE TELECOMMANDEE : TARBOSAURE
3+ years

 AN2864 RC Bumper Cars Tarbosaurus

TO START PLAYING:

  1. Make sure the ON/OFF switch on the vehicle is in the ON position (Fig. 3).
  2. Each time playing, press on the Top Reset Button on vehicle’s roof (Fig. 1), then press any button on the remote to start.

TROUBLESHOOTING:

In the event the remote and/or vehicle are not responsive, press the RESET BUTTON on the remote (Fig. 2) to continue playing. If the remote and/or vehicle still fail to connect, switch the vehicle OFF and back ON again (Fig. 3). Then press RESET BUTTON on the remote (Fig. 2). Continue with Step 2.
If the connection issue persists, replace the batteries in the vehicle (Fig. 3) and in the remote (Fig. 4) with new alkaline batteries. Continue with Step 1 & 2 to re-start.
NOTE: The vehicle will automatically go into sleep mode after 30 minutes of inactivity to save power.
Wake up by pressing on the Top Reset Button on vehicle’s roof (Fig. 1).
FIG. 1 FUNCTIONS

BATTAT AN2864 RC Bumper Cars Tarbosaurus - Fig 1

FIG. 2 FUNCIONESBATTAT AN2864 RC Bumper Cars Tarbosaurus - Fig
3 Frequency bands: 2405MHz-2475MHz
Maximum radio-frequency power: 5dbm
Use alkaline batteries for longer play time.
WARNING:
This toy produces flashes that may trigger epilepsy in sensitised individuals WARNING!: SMALL PARTS – CHOKING HAZARD. Not suitable for children under 3 years.
WARNING:CHOKINGHAZARD— Small parts.
Not for children under 3 years.
AN2864/AN2864Z/AN2929/AN2929Z
Alignment lever

STEERING ALIGNMENT ADJUSTMENT

If the vehicle does not drive in a straight line, adjust the alignment using the alignment lever. If the vehicle drifts to the left, turn the lever towards the “R”. If the vehicle drifts to the right, turn the lever towards the “L”.
Please remove all packaging materials before giving to children.
Please retain this information for future reference.
User Guide:

  1. Do not use near seawater or in dirty and dusty environments.
  2. Do not use in the rain or immediately after rainfall.
  3. If the vehicle gets wet, open the battery compartment immediately, remove batteries, and turn the vehicle upside down to dry.
  4. Always clean and dry the vehicle and remote after using outdoors to avoid damage.
  5. The remote’s control distance may be reduced when using indoors.
  6. The vehicle’s remote control may not work after long storage.

Follow the steps below to re-start:
A) Always replace the batteries in the vehicle with 3 new AAA alkaline batteries (Fig. 3).
B) Follow steps 1 and 2 on the first page to start playing.
C) If the vehicle does not work, put 2 new AAA alkaline batteries in the remote (Fig. 4).
D) Follow steps 1 and 2 on the first page to start playing.

BATTERY ADVICE

  1. Requires 10 x AAA (1.5V) batteries not included.
  2. Batteries should only be replaced by an adult.
  3. Do not mix old and new batteries.
  4. Do not mix alkaline, standard or rechargeable batteries.
  5. Do not re-charge non-rechargeable batteries.
  6. Rechargeable batteries are only to be charged under adult supervision.
  7. Rechargeable batteries are to be removed from the product before being charged.
  8. Ensure batteries are inserted with the correct polarity.
  9. Exhausted batteries should always be removed.
  10. The terminals should not be short circuited.

ATTENTION:
When the module’s functions lose performance, follow instructions carefully to install new batteries.

CAN ICES-3 (B)/NMB-3(B)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals