BATTAT WH1331 Z Micro Series RC Tow Truck User Manual
- June 10, 2024
- BATTAT
Table of Contents
BATTAT WH1331 Z Micro Series RC Tow Truck
Product Information
The product is a remote-controlled toy vehicle manufactured by Battat MD. The
vehicle requires 3 AAA alkaline batteries for operation and comes with a
frequency band of 2405MHz-2475MHz. The maximum radio-frequency power is 5dBm.
The remote control requires 2 AAA alkaline batteries, which are not included
in the package.
The toy produces flashes that may trigger epilepsy in sensitive individuals.
Product Usage Instructions
- Make sure the ON/OFF switch on the vehicle is in the ON position.
- Press on the vehicle’s roof, and then press any button on the remote to start playing.
- If the vehicle does not work, replace the batteries in the vehicle with 3 new AAA alkaline batteries and put 2 new AAA alkaline batteries in the remote. Follow steps 1 and 2 to start playing again.
- If the vehicle gets wet, open the battery compartment immediately, remove batteries, and turn the vehicle upside down to dry.
- Do not use near seawater or in dirty and dusty environments.
- Do not use in the rain or immediately after rainfall.
- Always clean and dry the vehicle and remote after using outdoors to avoid damage.
- The remote’s control distance may be reduced when using indoors.
- If the vehicle does not proceed in a straight line, adjust the steering alignment using the alignment lever. If the vehicle drifts to the left, turn the lever towards the right. If the vehicle drifts to the right, turn the lever towards the left.
Note: This product is not suitable for individuals who are sensitive to light flashes or prone to epilepsy.
INSTALLATION INSTRUCTION
TO START PLAYING:
- Make sure the ON/OFF switch on the vehicle is in the ON position (Fig. 1).
- ress on the vehicle’s roof, as indicated in (Fig. 2), then press any button on the remote, as indicated in (Fig. 3).
TROUBLESHOOTING
- NOTE: If the controller and/or vehicle are not responsive, press the RESET BUTTON on the back of the remote (Fig. 4) to continue playing. If the controller and/or vehicle still fail to connect, switch the vehicle OFF and back ON again (Fig. 1). Continue with step 2.
- If the connection issue persists, replace the batteries in the vehicle (Fig. 1) and in the remote (Fig. 4) with new alkaline batteries. Continue with step 1 & 2.
- NOTE: The vehicle will automatically go into sleep mode after 30 minutes of inactivity to save power. Wake up by pressing on the vehicle’s roof, as indicated in (Fig. 2).
- Frequency bands: 2405MHz-2475MHz Maximum radio-frequency power: 5dbm
- Use alkaline batteries for longer playtime.
- WARNING: This toy produces ashes that may trigger epilepsy in sensitized individuals.
- WARNING!: SMALL PARTS – CHOKING HAZARD. Not suitable for children under 3 years
Alignment lever
STEERING ALIGNMENT ADJUSTMENT
-
If the vehicle does not drive in a straight line, adjust the alignment using the alignment lever. If the vehicle drifts to the left, turn the lever towards the “R”. If the vehicle drifts to the right, turn the lever towards the “L”.
-
Please remove all packaging materials before giving to children
-
BATTERY ADVICE Requires 3 x AAA(1.5V) batteries for the truck (included) Requires 2 x AAA(1.5V) batteries for the remote control (not included) Non-rechargeable batteries are not to be recharged. Rechargeable batteries are to be removed from
the toy before being charged. Rechargeable batteries are only to be charged under adult supervision. -
Different types of batteries or new and used batteries are not to be mixed.
-
Only batteries of the same or equivalent type as recommended are to be used. Batteries are to be inserted with the correct polarity.
-
Exhausted batteries are to be removed from the toy.The supply terminals are not to be short-circuited.
-
ATTENTION: When the module’s functions lose performance, follow instructions carefully to install new batteries
-
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
User Guide:
- Do not use near seawater or in dirty and dusty environments.
- Do not use in the rain or immediately after rainfall.
- If the vehicle gets wet, open the battery compartment immediately, remove batteries, and turn the vehicle upside down to dry.
- Always clean and dry the vehicle and remote after using them outdoors to avoid damage.
- The remote’s control distance may be reduced when used indoors. 6. The vehicle’s remote control may not work after long storage. Follow the steps below to re-start: A) Always replace the batteries in the vehicle with 3 new AAA alkaline batteries (Fig. 1). B) Follow steps 1 and 2 on the rst page to start playing. C) If the vehicle does not work, put 2 new AAA alkaline batteries in the remote (Fig. 4). D) Follow steps 1 and 2 on the first page to start playing.
FCC
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference,
- this device must accept any interference received, including interference that may cause undesired operation.
Warning: changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device