ELRO TWIN LEDSPOT 2x10W Motion Sensor User Manual

: June 3, 2024
: ELRO

Table of Contents

TWIN LEDSPOT 2x10W Motion Sensor
Introduction
Safety precautions
Choosing a mounting location
Installation & Wiring instruction
First time power up
Specifications
Documents / Resources

ELRO TWIN LEDSPOT 2x10W Motion Sensor

MANUAL
Deutsch – Nederlands – Français
TWIN LEDSPOT 2 x 10 WATT
MOTION SENSOR
Home is not a place, it’s a feeling

TWIN LEDSPOT 2x10W Motion Sensor

ELRO TWIN LEDSPOT 2x10W Motion Sensor - fig https://eprel.ec.europa.eu/qr/1205776 ELRO TWIN LEDSPOT 2x10W
Motion Sensor - fig 1

Introduction

The LED Twinspot with PIR motion sensor is a fully automatic security spotlight. During the hours of darkness, the PIR motion sensor turns on the spotlight when it detects movement in the PIR coverage area. During daylight hour the PIR motion sensor saves energy by deactivating the spotlight.
Note: Please read this entire instruction manual before you start to install the spotlight.

Safety precautions

Installation must be performed by a skilled/competent person.
There are no serviceable parts inside.
Not suitable to be used with dimmer switches.
DO NOT install when it is raining.
During installation or servicing always turn off power.
The pre-wired supply cable must be used and may not be removed.

Choosing a mounting location

For the best results, mount the spotlight 1.8 – 2.4m above the ground.
Avoid aiming the PIR motion sensor at pools, heating vents, air conditioners or objects that may change temperature.
Avoid aiming the PIR motion sensor at trees or shrubs or where the movement of pets or animals may be detected.
DO not allow sunlight to fall directly onto the front of the PIR motion sensor, otherwise poor triggering response may occur.
Less sensitive to a heat source that moves directly towards the PIR motion sensor (1 page 2).
Consider the detection range/area when choosing a mounting location.

Installation & Wiring instruction

Drill the holes and insert suitable wall plugs. Fix the mounting bracket tot the wall using suitable screws (2 page 2).

An internal single pole wall switch is recommended to allow easy control of the LED Twinspot with PIR motion sensor (4 page 2).
If the connection is made outdoors a suitable IP box must be used to make the connections.
Do not remove the pre-wired supply cable, this will invalidate the warranty.

First time power up

Reinstate the power supply to the spotlight and switch the spotlight on from the wall switch if installed. The spotlight will turn on for around 2 seconds and then turns off.
Walk through the PIR motion sensor coverage area. The spotlight turns on when you move through the detection area. Wait for the spotlight to turn off before moving again to test the PIR motion sensor.
When you are happy with the coverage area you can set the spotlight to the desired TIME period and LUX level.

| Turn the TIME control knob towards the + sign to increase how long the spotlight stays on (up to about 12 minutes). The recommended setting for Time control is approximately midpoint of the scale (approximately 5 minutes).
---|---
| The LUX control can be adjusted between T (always triggered regardless of light level) and the moon symbol (triggered on only during hours of darkness). The recommended setting for the Lux control is fully turned to the moon symbol. IF the Lux control is left in the T position the spotlight will be triggered on by the PIR motion sensor regardless of the ambient light level.

Trouble shooting Spotlight does not turn on.
– Check Lux setting
– Check wall switch is on
– Confirm wiring is correct

Spotlight remains on
– Check time setting.
– Cover PIR motion sensor with black insulating tape. If after the timer set time expires the floodlight turns off this indicates that the PIR motion sensor can see a moving heat source. Eg: Open window, boiler outlet, open exterior door or moving branches or bushes retaining heat from the daytime period.

Spotlight flashes on and off
– PIR motion sensor being triggered off by reflected light.

Specifications

Power requirement	: 220V – 240V, 50Hz
Power cord	: H05RN-F, 3G, 0,75 mm² x 90 cm
Lighting load	: 20W
Lumen (lm)	: >1400lm
Color temperature (K)	: 6500K
Lux adjustment	: 0 – 1000 Lux
Time adjustment	: 5sec. – 12 min.
Protection Degree	: IP54

Environmental concerns:
Please DO NOT dispose of electrical appliances as unsorted waste, use the recycling facilities provided by your local authorities. Please DO NOT dispose of packaging as unsorted waste, use the recycling facilities provided by your local authorities. There are no user serviceable parts inside. When the lifespan of the light source comes to an end, the whole luminaire will need to be replaced.

Warning:
The external flexible cable cord of this luminaire cannot be replaced; if the cord is damaged, the luminaire shall be destroyed. The light source of this luminaire is not replaceable; when the light source reaches its end of the life the whole luminaire shall be replaced.

Warranty:
The manufacturer guarantees this lighting fixture to be free from defects in materials and workmanship for a period of 2 years warranty from date of purchase.

Concluding remarks:
Thank you very much for your trust and choice to purchase our product.
If you have any issues about this product, please feel free to contact us: www.elro.eu

ELRO Europe | www.elro.eu
Postbus 9607 – Box E800
1006 GC Amsterdam – The Netherlands

Documents / Resources

| ELRO TWIN LEDSPOT 2x10W Motion Sensor [pdf] User Manual
TWIN LEDSPOT 2x10W Motion Sensor, TWIN LEDSPOT, 2x10W Motion Sensor, 2x10W LEDSPOT, Motion Sensor LEDSPOT, Motion Sensor, LEDSPOT
---|---