Auisre A04971W2 14-in 2 Light Matte Black Polished Gold Instruction Manual

Auisre A04971W2 14-in 2 Light Matte Black Polished Gold

Product Information

Product Name: [Product Name] Item Number: A04971W2
Voltage: 120V
Maximum Wattage: Type A, Max 60W per bulb
Product Dimensions: [Dimensions]

Product Usage Instructions

1. Before starting assembly and installation, make sure to gather the following tools:
   • Ladder
   • Philips Head or Flat Blade Screwdriver
   • Electrical Tape
   • Pliers
   • Wire Cutter/Stripper
2. Carefully remove the fixture from the carton and ensure that all parts and accessories are included.
3. Turn off the power before starting the installation.
4. Secure the mounting plate (C) to the outlet box using the provided mounting screws (A).
5. Connect the wires according to the below chart:

*Parallel cord (square & ridged)
Clear, Brown, Gold or Black without tracer| Insulated wire (other than green) with copper conductor
Insulated wire (other than green) with silver conductor

1. After connecting the wires, proceed with the remaining assembly steps as shown in the user manual.

If you have any further questions or need assistance, please contact our customer care team at +1 850 296 2377 during our working hours: Mon – Fri 9:00 – 16:00 EST or email us at homecustomercare@outlook.com.

Item Number: A04971W2

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.

2. Please read the instruction carefully and save it as you may need it at a later time.

3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. » Go to the main fuse, or circuit breaker, box in your home.
   Place the main power switch in the “OFF” position. » Place the wall switch in the “OFF” position.

4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

6. Make sure the voltage you are using is 120V. The maximum wattage is Type A, Max 60W per bulb.

7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED (NOT INCLUDED)

Before starting assembly and installation please prepare the needed tools as below picture

PARTS INCLUDING

• (C) Mounting plate (1)
• (D) Green ground screw (1)
• (E) Back plate (1)
• (F) Stud (2)
• (G) Upper cover (2)
• (H) Thumbscrew (12)
• (I) Metal strip (6)
• (J) Ring (2)
• (K) Glass shade (2)

ACCESSORIES ENCLOSED:

• (A) Mounting screw (2)
• (B) Plastic wire connector (3)
• (H) Screw (1) (Spare part)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

3. Go to the main fuse, or circuit breaker, box in your home.
   Place the main power switch in the “OFF” position.

4. Place the wall switch in the “OFF” position.

5. Make assembly

Step A1
Unscrew studs (F) from back plate (E), then set them aside for later installation.

Step A2
Carefully pass the supply wires from the outlet box through mounting plate (C).
Secure mounting plate (C) to the outlet box with mounting screws (A).

Step A3
Make wire connections

Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect ground wires according to the below chart

Connect wires according to the below chart

Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)

Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

Step A4
Align the holes in back plate (E) and mounting plate (C), then secure them with the previously removed studs (F).
Step A5

1. Unscrew thumbscrews (H) from upper covers (G) and rings (J).
2. Pass thumbscrews (H) through the holes of metal strips (I), rings (J) and glass shades (K), then tighten thumbscrews (H) as shown in the illustration.
3. Pass thumbscrews (H) through the holes of metal strips (I) and upper covers (G), then tighten thumbscrews (H) as shown in the illustration.
4. Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)

Check everything is installed properly, then you could turn on the light. Enjoy!

ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts

CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

+1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST

homecustomercare@outlook.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>