Kaysun KID-05.4 S Remote Controller User Manual

KID-05.4 S Remote Controller
User Manual

IMPORTANT NOTE:

** Thank you for purchasing our air conditioner. Please read this manual carefully before operating your new air conditioning unit. Make sure to save this manual for future reference.
Remote Controller Specifications**

Quick Start Guide NOT SURE WHAT A FUNCTION DOES?
Refer to the How to Use Basic Functions and How to Use Advanced Functions sections of this manual for a detailed description of how to use your air conditioner.
SPECIAL NOTE

• Button designs on your unit may differ slightly from the example shown.
• If the indoor unit does not have a particular function, pressing that function’s button on the remote control will have no effect.
• When there are wide differentces between “Remote controller Manual” and “USER’S MANUAL” on function description, the description of “USER’S MANUAL” shall prevail.

Handling the Remote Controller

Inserting and Replacing Batteries
Your air conditioning unit may come with two batteries(some units). Put the batteries in the remote control before use.

1. Slide the back cover from the remote control downward, exposing the battery compartment.
2. Insert the batteries, paying attention to match  up the (+) and (-) ends of the batteries with the symbols inside the battery compartment.
3. Slide the battery cover back into place.

BATTERY NOTES
For optimum product performance:

• Do not mix old and new batteries, or batteries of different types.
•  Do not leave batteries in the remote control if you don’t plan on using the device for more than 2 months.

BATTERY DISPOSAL
Do not dispose of batteries as unsorted municipal waste. Refer to local laws for proper disposal of batteries.

TIPS FOR USING REMOTE CONTROL

• The remote control must be used within 8 meters of the unit.The unit will beep when remote signal is received.
• Curtains, other materials and direct sunlight can interfere with the infrared signal receiver.
•  Remove batteries if the remote will not be used more than 2 months.
• Prevent any liquid from falling into the remote control.

NOTES FOR USING REMOTE CONTROL
The device could comply with the local national regulations.

•  In Canada, it should comply with CAN ICES-3(B)/NMB-3(B).
• In USA, this device complies with part 15 of the
  FCC Rules. Operation is subject to the following two conditions:

1.  This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
   This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to  radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced  adio/TV technician for help.
• Changes or modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.

Buttons and Functions
Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control. The following is a brief introduction to the remote control itself. For instructions on how to operate your air conditioner, refer to the How to Use Basic Functions section of this manual.

Remote Screen Indicators

Information are displayed when the remote controller is power up. Note:
All indicators shown in the figure are for the purpose of clear presentation. But during the actaul operation, only the relative function signs are shown on the display window.
How to Use Basic Functions
Basic operation
ATTENTION! Before operation, please ensure the unit is plugged in and power is available. COOL Mode

1. Press the MODE button to select COOL mode.
2. Set your desired temperature using the   TEMP or TEMP button.
3. Press FAN button to select the fan speed in a range of AU-100%.
4. Press the ON/OFF button to start the unit.

SETTING TEMPERATURE
The operating temperature range for units is 16-30°C (60-86°F). You can increase or decrease the set temperature in 0.5°C (1°F) increments.
AUTO Mode
In AUTO mode, the unit will automatically select the COOL, FAN, or HEAT operation based on the set temperature.

1. Press the MODE button to select AUTO.
2. Set your desired temperature using the TEMP or TEMP button.
3. Press the ON/OFF button to start the unit.

NOTE: FAN SPEED can’t be set in AUTO mode.

FAN Mode

1. Press the MODE button to select FAN mode.
2. Press FAN button to select the fan speed in a range of AU-100%.
3. Press the ON/OFF button to start the unit. 3.

NOTE: You can’t set temperature in FAN mode. As a result, your remote control’s LCD screen will not display temperature.

DRY Mode (dehumidifying )

1. Press the MODE button to select DRY.
2. Set your desired temperature using the TEMP or TEMP button.
3. Press the ON/OFF button to start the unit.

NOTE: FAN SPEED cannot be changed in DRY mode.

HEAT Mode

1. Press the MODE button to select  Select HEAT mode.
2. Set your desired temperature using the TEMP or TEMP button.
3.  Press FAN button to select the fan speed in a range of AU-100%.
4. Press the ON/OFF button to start the unit.

NOTE: As outdoor temperature drops, the performance of your unit’s HEAT function may be affected. In such instances, we recommend using this air conditioner in conjunction with other heating appliances.
Setting the TIMER
TIMER ON/OFF – Set the amount of time after which the unit will automatically turn on/off.
TIMER ON setting

Press TIMER button to initiate the ON time sequence.| Press Temp. up or down button for for multiple times to set the desired time to turn on the unit.| Point remote to unit and wait 1sec, the TIMER ON will be activated.
---|---|---

TIMER OFF setting

Press TIMER button to initiate the OFF time sequence.| Press Temp. up or down button for for multiple times to set the desired time to turn off the unit.| Point remote to unit and wait 1sec, the TIMER OFF will be activated.
---|---|---

NOTE:

1. When setting the TIMER ON or TIMER OFF, the time will increase by 30 minutes increments with each press, up to 10 hours. After 10 hours and up to 24, it will increase in 1 hour increments. (For example, press 5 times to get 2.5h, and press 10 times to get 5h,) The timer will revert to 0.0 after 24.
2. Cancel either function by setting its timer to 0.0h.

TIMER ON & OFF setting(example)
Keep in mind that the time periods you set for both functions refer to hours after the current time. Example: If current timer is 1:00PM, to set the timer as above steps, the unit will turn on 2.5h later (3:30PM) and turn off at 6:00PM.

How to Use Advanced Functions

Swing function
Press Swing button

The horizontal louver will swing up and down automatically when pressing Swing button. Press again to make it stop.| Keep pressing this button more than 2 seconds,  the vertical louver swing function is activated. (Model dependent)

Airflow direction If continue to press the SWING button, five different airflow directions can be set. The louver can be move at a certain range each time you press the button. Press the button until the direction you prefer is reached.
NOTE: When the unit is off, press and hold MODE and SWING buttons together for one second, the louver will open for a certain angle, which makes it very convenient for cleaning. Press and hold MODE and SWING buttons together for one second to reset the louver(Model dependent).
LED DISPLAY Press this button to turn on and turn off the display on the indoor unit. Keep pressing this button more than 5 seconds, the indoor unit will display the actual room temperature. Press more than 5 seconds again will revert back to display the setting temperature.
Cascade feature
Press this button to adjust activate Cascade feature in a sequence of following:
Upward Cascade( ) Downward Cascade( ) Cancel Cascade feature This feature enables the whole room to be cool quickly and evenly. The system will adjust the louver angles and fan speed automatically. You can also choose the fan speed by remote controller.
Note: This function is only available under COOL or Fan mode.
ECO/GEAR function Press this button to enter the energy efficient mode in a sequence of following:
ECO GEAR(75%) v GEAR(50%) Previous setting mode ECO…… Note:This function is only available under COOL mode.
ECO operation:
Under cooling mode, press this button, the remote controller will adjust the temperature automatically to 24 C/75 F, fan speed of Auto to save energy (only when the set temperature is less than 24 C/75 F). If the set temperature is above 24 C/75 F, press the ECO button, the fan speed will change to Auto, the set temperature will remain unchanged.
NOTE:
Pressing the this button, or modifying the mode or adjusting the set temperature to less than 24 C/75 F will stop ECO operation.
Under ECO operation, the set tmeperature should be 24 C/75 F or above, it may result in insufficient cooling. If you feel uncomfortable, just press the ECO button again to stop it.
GEAR operation :
Press the ECO/GEAR button to enter the GEAR operation as following:

75%(up to 75% electrial energy consumption)

50%(up to 50% electrial energy consumption) Previous setting mode.
Under GEAR operation, the display on the remote controller will alternage between electical energy consumption and set temperature.
Breeze Away Function Press this button to adjust the breeze away from people in a sequence of following:
Upward Breeze away from people( )  Downward Breeze away from people( ) Cancel Breeze away feature
This feature avoids direct air flow blowing on the body and makes you feel indulging in silky coolness.
Note :This function is only available under COOL, Dry or Fan mode.
Silence function Keep pressing Fan button for more than 2 seconds to activate/disable Silence function(some units).
Due to low frequency operation of compressor, it may result in insufficient cooling  and heating capacity. Press ON/OFF, Mode, Sleep, Turbo or Clean button while operating will cancel silence function.
FP function The unit will operate at high fan speed (while compressor on) with temperature automatically set to 8 C/46 F.
Note: This function is for heat pump air conditioner only.
Press this button 2 times during one second under HEAT Mode and setting temperature of 16 C/60 F to activate FP function.Press On/Off, Sleep, Mode, Fan and Temp. button while operating will cancel this function.
LOCK function
Press together Turbo button and Cascade button at the same time more than 5 seconds to activate Lock function. All buttons will not response except pressing these two  buttons for two seconds again to disable locking.
Turbo Function
Press Turbo button When you select Turbo feature in COOL mode, the unit will blow cool air with strongest wind setting to jump-start the cooling process.
When you select Turbo feature in HEAT mode, for units with Electric heat elements, the Electric HEATER will activate and jump-start the heating process.
SET function

• Press the SET button to enter the function setting, then press SET button or TEMP or TEMP button to select the desired function. The selected symbol will flash on the display area, press the OK button to confirm.
• To cancel the selected function, just perform the same procedures as above.
• Press the SET button to scroll through operation functions as follows:

Active clean ( ) Fresh ( ) Sleep( ) Follow Me( ) AP mode ( ) [ *] : Model dependent
Active clean function( ) (some units) :
The Active Clean Technology washes away dust, and mold that may cause odors when it adheres to the heat exchanger by automatically freezing and then rapidly thawing the frost. When this function is turned on, the indoor unit display window appears “CL”, after 20 to 130 minutes, the unit will turn off automatically and cancel CLEAN function.
FRESH function( ) (some units) :
When the FRESH function is initiated, the ion generator is energized and will help to purify the air inside.
Sleep function( ) :
The SLEEP function is used to decrease energy use while you sleep (and don’t need the same temperature settings to stay comfortable). This function can only be activated via remote control.
For the detail, see sleep operation in USER S MANUAL.,
Note: The SLEEP function is not available in FAN or DRY mode.
Follow me function( ) :
The FOLLOW ME function enables the remote control to measure the temperature at its current location and send this signal to the air conditioner every 3 minutes interval.
When using AUTO, COOL or HEAT modes, measuring ambient temperature from the remote control(instead of from the indoor unit itself) will enable the air conditioner to optimize the temperature around you and ensure maximum comfort.
NOTE: Press and hold Boost button for seven seconds to start/stop memory feature of Follow Me function. If the memory feature is activated, “On” displays for 3 seconds on the screen. If the memory feature is stopped, “OF” displays for 3 seconds on the screen. While the memory feature is activated, press the ON/OFF button, shift the mode or power failure will not cancel the Follow me function.
AP function( )(some units) :
Choose AP mode to do wireless network configuration. For some units, it doesn’t work by pressing the SET button. To enter the AP mode, continuously press the LED button seven times in 10 seconds.
The design and specifications are subject to change without prior notice for product improvement. Consult with the sales agency or manufacturer for details.
CR286-RG10KX(2HS)

MAIN OFFICE
Blasco de Garay, 4-6
08960 Sant Just Desvern (Barcelona)
Tel. +34 93 480 33 22
http://www.frigicoll.es/
http://www.kaysun.es/en/
MADRID
Senda Galiana, 1
Poligono Industrial Coslada
Coslada (Madrid)
Tel. +34 91 669 97 01
Fax. +34 91 674 21 00
madrid@frigicoll.es

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>