BAINTECH Switch Mode Smart Battery Charger Instruction Manual

BAINTECH Switch Mode Smart Battery Charger

Important Information!
Thank you for purchasing the multi-stage Smart Battery Charger. Please read this instruction manual carefully before operating the device. Keep this manual in a safe place for future reference. This instruction manual is part of the product. It must be handed over along with the device if it is passed on to a third party.

SWITCH MODE SMART BATTERY CHARGER

charging Setting

Safety Operation

• The device is for indoor use, do not use the device near flammable materials.
• The appliance shall only be used with rated voltage and frequency.
• If cables have to be fed through walls with sharp edges, always use tubes or ducts to prevent damage.
• Children should be supervised to ensure that they do not play with the device.
• Do not allow water to drip or splash on the device.
• Make sure the air inlets and outlets of the device are not covered.
• Do not reverse the polarity of the connection to the battery.
• Do not charge non-rechargeable batteries.
• Disconnect the supply before making or breaking the connections to the battery.
• Caution! Hot surface when operating at full load condition.

SWITCH MODE SMART BATTERY CHARGER

Troubleshooting

Warranty

only covers the cost of parts and labor for the repair service within the warranty period. Warranty will not apply where the device has been misused, altered, neglected, improperly installed physically damaged, either internally or externally, or damaged from proper use or use in an unsuitable environment. We shall not be liable for damages, whether direct, incidental, special, consequential, or economic loss even though caused by negligence or other fault. If the device requires warranty service, please return it to the place of purchase along with a copy of the receipt with the purchase date.

Disposal
When the device has become unusable, dispose of it in accordance with the applicable disposal regulations.

SWITCH MODE SMART BATTERY CHARGER

Introduction

This compact smart multi-stage battery charger uses the latest switch-mode technology and is designed particularly to charge lead-acid batteries and LiFePO4 batteries to their best level. The multi-stage charging algorithm delivers a much faster, more efficient, and full charge without the issue of voltage drops. Thanks to the boost-charging feature, this helps activate the battery status and wake up a weak or flat battery le recharging level. This also improves the charge delivered to your battery. saving on premature battery failure.

This smart battery charger is equipped with a selector that allows you to set the charger for charging SLA/GEL/AGM/Flooded/Calcium lead-acid batteries and LiFePO4 batteries. The smart battery charger can be used as a constant power supply to run accessories that require stable and clean voltage. For safety reasons, the input and output of the charger are completely isolated and the batteries are protected from overcharging. The cooling fan is thermally controlled. It will switch on and off automatically to control the internal temperature of the unit

Warning!
Risk of electric shock! Do not open the device if it has been connected to the AC power source. This device has been CE-tested and conforms to the applicable directives and standards

Instruction and normal responses

Operation as Charger under standard charging mode Select the switch to position S and select dip switch No. 1-5 to get the optimum charge to suit your battery specification. Connect the AC input cable to the utility. Connect the battery to the DC output. Turn On the Power switch. The “POWER ON”LED lights up. This indicates the device is ready for charging. The”BULK* LED lights up. This means the battery charger is beginning at the

1St stage of charging
The 1st stage is to ensure the battery is always charged at the maximum charging condition. This is to boost up the charging cycle and particularly wake up a weak battery to absorb energy. At the 2nd stage, the charger will switch to”ABSORPTION mode, The charger delivers constant voltage to the battery with reduced current. In the 3rd stage, the battery has been charged to about 90% of its rated capacity. The ABSORPTION LED goes out and the ‘FLOAT” LED lights up. The charging current is decreased and the charging voltage is held at a constant level. The battery is now under constant charging

Operation as Charger under LiFeP04 Charging Mode
Select the switch to position L and set dipswitch to charge the LiFePO4 battery.

Operation as Power Supply
Select the switch to position P, the device now operates as a power supply unit. The Bulk and The absorption LED go out. Select dip switch No. 6 for constant Voltage.

Charging Curve

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>