Disnep CW-10368 Star Wars Holiday TIE Fighter Gingerbread Cardboard Cat House Instructions
- June 3, 2024
- Disnep
Table of Contents
STAR WARS™ Holiday TIE FIGHTER™ Gingerbread Cardboard Cat House
CW-10368
CW-10368 Star Wars Holiday TIE Fighter Gingerbread Cardboard Cat House
Because every cat is different, it is important to monitor your cat’s behavior
with this product. If at any time your cat damages this item, or any portion
of this item becomes damaged, remove the damaged portion or discontinue use of
the product.
QUESTIONS?
CALL OUR FRIENDLY CUSTOMER SERVICE TEAM ANYTIME. WE’RE HERE
24/7!1-800-67-CHEWY (672-4399)
This Package Contains
STAR WARS™ Holiday TIE FIGHTER™ Gingerbread Cardboard Cat House (2/6)
Step 1
Fold Strut (J) as shown below. Lock tabs into slots.| Step 2
Pre-fold and roll Cockpit (H) as shown below. Insert tab into slot.
---|---
Step 3
Attach Sides (L&K) to Cockpit (H) by inserting tabs into slots as
shown below. Match the numbers on the tabs for the correct
orientation.| Step 4
Reinforce connections by placing Clear Stickers (X) over the tabs and
slots of Lower Panels as shown
STAR WARS™ Holiday TIE FIGHTER™ Gingerbread Cardboard Cat House (3/6)
Step 5
Insert Strut (J) through completed Cockpit as shown below.| Step 6
Fold Wings (E) as shown below.
---|---
Step 7
Attach Wings to Cockpit as shown below. Arrange the panels
according to the reference below| Step 8
Fold tabs and insert into slots as shown below. Repeat on both sides.
STAR WARS™ Holiday TIE FIGHTER™ Gingerbread Cardboard Cat House (4/6)
Step 9
Attach Roof (F) to Braces (G). Fold tabs and insert into larger slots
as shown below.| Step 10
Wrap around the side of Braces (G) and insert tabs into larger slots
on the other side.
---|---
Step 11
Lock roof in place by inserting tabs into smaller slot as shown below.| Step
12
Fold Side Walls (C & D) of upper panels as shown below.
Page size: 8.5” x 11” ( Sheet 2 Back Side )
STAR WARS™ Holiday TIE FIGHTER™ Gingerbread Cardboard Cat House (5/6)
Step 13
Attach Completed Roof to side walls by inserting Braces into slots
of Walls. Push down to lock fully in place.| Step 14
Line up Front Panel (A) and Back Panel (B) with Completed Panels. With the
graphics on the tabs lining up, fold tabs and insert into larger slots.
---|---
Step 15
Lock sides in place by inserting tabs into smaller slot as shown
below.| Step 16
Attach Assembled Ship to roof by inserting tabs into slots as shown
below.
Page size: 8.5” x 11” ( Sheet 3 Front Side )
STAR WARS™ Holiday TIE FIGHTER™ Gingerbread Cardboard Cat House (6/6)
Step 17
Remove protective film from double-sided tape of Corrugate Board
(W). Slide Completed Panels down over the sides until it rests over (W) as
shown. Press to attach the board to the front and back
panels.| Step 18
Remove protective film from double-sided tape of Side Characters (N & M)
attach stickers anywhere on the house.
---|---
Last Step
Remove protective film from double-sided tape of Small Characters (P, Q, R, S,
T, U & V) attach stickers anywhere on the
house.| Completed Item
Page size: 8.5” x 11” ( Sheet 3 Back Side )
©Disney
disney.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>