Goldair GPPH770 Electronic Inverter Panel Heater with Wi-Fi Instruction Manual

Goldair GPPH770 Electronic Inverter Panel Heater with Wi-Fi

General Care and Safety Guide

YOUR SAFETY IS IMPORTANT TO US. PLEASE ENSURE YOU TAKE NOTE OF THE INSTRUCTIONS AND WARNINGS OUTLINED IN THIS MANUAL.

CAUTION  In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they are supervised or have been given instruction concerning the use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.
• You must not cover this appliance. Covering this appliance presents a fire risk and will activate the safety fuse; permanently disabling the unit.
• Do not use this appliance in small rooms when they are occupied by persons not capable of leaving the room on their own unless constant supervision is provided.
• To reduce the risk of fire, keep textiles, curtains, or any flammable material a minimum distance of 1 meter from the air outlet.
• Use only the voltage specified on the rating label of the appliance.
• Keep all objects at least 1 meter from the front and 150mm from the sides of the appliance.
• This appliance is intended for household use only and not for commercial or industrial use.
• Indoor use only.
• Use this appliance only as described in this manual. Any other use is not recommended by the manufacturer and may cause fire, electric shock, or injury.
• Do not use the appliance if it has been dropped or damaged.
• The common cause of overheating is deposits of dust or fluff in the appliance. Ensure these deposits are removed regularly by unplugging the appliance and vacuum cleaning the air vents and grills.

Never use the appliance to dry clothes.

• Always unplug appliances when not in use.

• When the appliance has been unpacked, check it for transport damage and ensure all parts have been delivered. If parts are missing or the appliance has been damaged, contact the Customer Services Team.

• Do not use it if there are visible signs of damage to the appliance.

• Do not connect the appliance to the main supply until completely assembled and adjusted.

• Ensure hands are dry before handling the plug or main unit.

• Ensure the appliance is on a flat, stable, heat-resistant surface.

• Do not operate with the cord set coiled up as a heat build-up is likely, which could be sufficient to become a hazard.

• Carry out regular checks of the supply cord to ensure no damage is evident

• Do not operate this appliance with a damaged cord, plug, or after the appliance malfunctions or has been dropped or damaged in any manner. Take to a qualified electrical person for examination, electrical service, or repair.

• Do not twist, kink, or wrap the cord around the appliance, as this may cause the insulation to weaken and split. Always ensure that all cord has been removed from any cord storage area and is unrolled before use.

• It is recommended that this appliance is plugged directly into the wall socket. Powerboards are not rated to supply power to high-wattage appliances.

• A correctly specified, an undamaged extension cord may be used with this appliance provided it is used in a safe manner.

• Do not remove the plug from the power socket until the appliance has been switched off.

• Do not remove the plug from power socket by pulling cord; always grip plug.
  Do not place a cord under the carpet or cover it with rugs or furniture. Arrange the cord so it cannot be tripped over.

• Don’t place appliances on bedding or on thick & long carpet where the openings may get blocked.

• Switch off and use the handle provided when moving

• Do not place the appliance close to a radiant heat source.

• Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock, fire, or damage to the appliance.

• Do not sit on the appliance.

• Do not use abrasive cleaning products on this appliance. Clean with a damp cloth (not wet) and rinsed in hot soapy water only. Always remove the plug from the mains supply before cleaning.

• Do not operate in areas where petrol, paint, or other flammable liquids are used or stored.

• Do not use this appliance in the immediate surroundings of a bath, a shower, a swimming pool, or other liquids.

• The appliance must not be immersed in any liquids.

• There are no user-serviceable parts installed in the unit.

• Do not place the unit in wardrobes or other enclosed spaces as this may cause fire hazards.

• This unit is not supposed to be used in or around locations where foodstuffs, works of art or delicate articles of science, etc. are stored.

• If your appliance does not work or is not working properly, contact the place of purchase or the Customer Services Team.

OVERHEAT PROTECTION” FUNCTION

The device is equipped with an automatic switch that is activated when the upper-temperature limit is reached. The heater switches off automatically in case of overheating. After eliminating the source of overheating, the heater will turn on automatically.

Components

Assembly Instructions

Before using this appliance, it must either be wall-mounted or have the feet fitted. This appliance has been supplied with ‘1-way screws’ for permanent installation of the feet. This is a safety requirement for the New Zealand and Australian markets.

FREESTANDING

1. Ensure the appliance is unplugged and power switches are off.
2. Insert the matching feet brackets into the matching feet until they click into place –some force may be required.
3.  Carefully turn the main body upside-down on a scratch-free and stable surface. Be careful to prevent damage to the cosmetic finish or your floor surfacing.
4. Align the screw hole on the Heater Feet Bracket with the screw hole on the base of the appliance.
5. Attach Heater Feet Bracket with the ‘1-way screws’ provided and ensure the bracket sits firmly in place (do not over tighten).
6. Set appliance upright.
7. NOTE: The wall bracket edges may be sharp. It is recommended that if used as a free-standing appliance please remove the wall bracket from the back of the heater.

Installation Instructions

The appliance must not be located immediately below a socket outlet. Your Panel Heater should be installed with at least 150mm clearance from the floor and any other surrounding parts including other appliances and sidewalls. At least 300mm clearance from ceilings, shelves, and soft furnishings. Do not run the power cord behind the heater.

WALL-MOUNTED HEATERS ARE ONLY TO BE MOUNTED ON HEAT RESISTANT WALLS THAT COMPLY WITH CURRENT AS/NZS SPECIFICATIONS & BUILDING REGULATIONS

WALL-MOUNTED

1. Make sure the appliance is unplugged and the power switches are off.
2. Position the panel appliance within one meter of a wall socket. Do not mount in front of or below the wall socket. Ensure there is at least 150mm clearance on all sides of the appliance.
3.  Detach the mounting bracket from the back of the panel appliance by unscrewing the two locking screws (located on the top of the mounting bracket).
4. Position the mounting bracket on the wall and mark the hole positions with a pen or pencil and check they are horizontal with a spirit level. Ensure the two bottom mount holes are at least 150mm from the floor and drill holes as required.
5. Secure the mounting bracket to the wall with the mounting screws. (For masonry walls use the plastic sheaths).
6. Slot the back of the appliance onto the mounting bracket locating the bottom plugs first and securing with two locking screws.
7. Plug appliance into a standard 240 volt AC electrical outlet.

Operating Your Heater

• Always choose a safe location for the heater, keeping in mind the safety precautions outlined. Ensure all packaging has been removed from the unit before use. Please follow the below instructions.
• In order to avoid overheating or fire, do not cover the heater.
• Keep all objects at least 1 meter from the front and 150mm from the sides of the appliance.
• Do not use this heater with a programmer, separate timer, remote-control system or any other device that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned incorrectly.
• Never leave this heater unattended when in use.
• If mounted on castors, ensure the heater is on a flat, stable, heat-resistant surface.
• Once the heater is in a safe operating position and all switches are in the off position, insert the power plug into the main outlet and switch it on.
• Ensure the power cord is not tight because if pulled it may partially pull the plug from the socket. A partially inserted plug will overheat the plug and socket and could result in fire.
• When the appliance is turned on for the first time, it may release a slight odor or smoke. This odor or smoke is a normal occurrence caused by the initial heating of the heating elements and should not occur again.

Operating Your Heater

DISPLAY CONTROLS

1. Indication of temperature mode – Comfort
2. Indication of temperature mode – Eco
3. Indication of temperature mode – Anti-Frost
4. Display of function “Open Window”
5. Indication of “Timer Off” function (to turn off)
6. Heating mode indication
7. Heating mode indication
8. Indication of heating power levels
9. Indication of work on schedule (Wifi Only) Indication of Wi-Fi operation
10. Control lock indication
11. Control unlock indication
12. Display target temperature

ERROR MESSAGES

1. Temperature sensor malfunction. Contact customer services.
2. Short circuit on temperature sensor channel. Contact customer services.
3. Overheating of temperature sensor (exceeded +48 degrees). Turn off the heater to allow it to cool down.
4. The ambient temperature has dropped too low (below -26 degrees). Turn off the heater to allow the ambient temperature to rise.

Operating Your Heater

SETTINGS MENU DIAGRAM

Operating Your Heater

• Check that the heater’s main power switch is in the OFF position before plugging it into the main supply.

• ON/OFF BUTTON

• Hold down for 3 seconds to turn the heater ON/OFF. The default temperature is 24°C.

• OPEN WINDOW

• When this function is active, if the temperature drops by 5°C or more within a 10-minute period, the Anti-Frost mode is switched on. If in the time interval of 10-30 minutes the temperature continues to drop, the device will turn off. If the room temperature rises by 2°C, then the last set mode will turn back on.

• CHILD LOCK

• Hold down the left and right arrows simultaneously for 5 seconds to enable child lock. The device controls cannot be changed. To disable child lock, hold down the left and right arrows for another 5 seconds.

• NAVIGATING THE MENU

• Use the buttons to navigate through all the menu options and button to confirm your selection

• HEAT MODE

• There are 3 temperature modes available for adjustment

• Comfort Range from 1010°C to 3535°C

• Eco Deviation range from Comfort from 33°C to 77°C

• Anti Frost Range from 33°C to 77°C Use the buttons to navigate and the button to firstly confirm your desired mode and then desired temperature Note Temperature can only be amended on the device when in Comfort mode If you press the left or right button in Eco/Anti Frost mode in order to amend the temperature, the heater will switch to Comfort mode

• POWER

• Anti Frost Range from 33°C to 77°C Use the buttons to navigate and the button to firstly confirm your desired mode and then desired temperature Note Temperature can only be amended on the device when in Comfort mode If you press the left or right button in Eco/Anti Frost mode in order to amend the temperature, the heater will switch to Comfort modeChoose desired power mode between Auto the heating element is inversely controlled Custom choose desired heat setting between 1 5 using the buttons to navigate and the button to confirm.

• TIMER

• This device has a countdown timer that will allow you to set a specific amount of time before turning the heater off
  Use the and buttons to navigate to the Timer function and turn the Timer
  function from OFF to ON.

• Set the time for the desired length of time you would like the heater to remain on.
  For example, if you want the heater to turn off in 3 hours and 30 minutes you would set
  the timer to 03:30. To cancel the Timer, you must go back to the Timer function and
  amend from ON to OFF.

• This device has a full weekly scheduler function available to operate via the app. Operating the scheduler and timer at the same time is not possible.

• SETTINGS
  Use the buttons to navigate through all the menu options and the button to confirm your selection

• DATE AND TIME

• Set the current date and time for the best functionality of your heater

• DISPLAY

• Brightness Choose between 100 %%(default setting) and 50 screen brightness

• SOUND

• Choose to have sound when buttons are pressed ON/OFF The default setting is ON

• SERVICE

• Connection Use this function to connect to the Goldair app To learn more about this device’s WiFi, please see the WiFi/App section of this manual

• Reset Choose to reset the device to default settings

• Information See the device’s current firmware version

• “AUTO RESTART/RESUME” FUNCTION
  In the event of a short term power outage, the last operating mode/ temperature will automatically be restored once the power comes back on

WiFi Downloading and Setting up APP

This APP is supported only on 2.4GHz Wi-Fi channels. Please ensure your phone is 2.4GHz capable Note this device will only work within your home WIFI system. This does not operate on 3G or 4G internet connections. You will need a connection to your home Wi-Fi.

• Download the Goldair mobile APP
• Open the APP Store or Google Play on your mobile phone
• Open ‘Search’ and enter ‘Goldair’
• Click ‘GET’ and begin to download and install.
• Once downloaded to your phone open the APP
• Tap REGISTER near the bottom of the screen.
• Read and agree to the Privacy Policy.
• Add your email address.
• Tap ‘Obtain verification
• You will then receive an email with a verification code.
• Enter the verification code from your email.
• Create a password.
• Then tap confirm.

If you haven’t received a verification code via email, tap the resend button, and when the verification code is received follow the above steps. Your APP is now registered and ready for pairing to your device.

Pairing APP to Heater

Details for pairing this heater to the Goldair App can be found at the below website link Either scan the QR code below or enter the website into your browser Wifi User Manuals – Goldair.nz

Care and Cleaning

• The heater requires regular cleaning to ensure trouble-free operation
• Unplug the heater from the mains supply before cleaning
• Ensure that the heater has been allowed to cool down completely before cleaning
• The common cause of overheating is deposits of dust or fluff in the appliance
• Ensure these deposits are removed regularly by unplugging the appliance and vacuum cleaning the air vents and grills
• Use a damp cloth (not wet) to wipe the exterior of the heater to remove dust and dirt
• Never use solutions such as petrol, thinners, or polishing agents
• Ensure the heater is dry before plugging back into the main supply.

ERROR MESSAGES

• Temperature sensor malfunction. Contact customer services.
• Short circuit on temperature sensor channel. Contact customer services.
• Overheating of temperature sensor (exceeded +48 degrees). Turn off the heater to allow it to cool down.
• The ambient temperature has dropped too low (below 26 degrees). Turn off the heater to allow the ambient temperature to rise.

Operating Your Heater

SAFETY DEVICES

• This appliance has three protection devices
• Tilt Switch this will automatically turn the appliance off if the appliance is not in the correct operating position
• Resettable Thermal Link this will automatically disconnect the power to the appliance at a preset overheat temperature After cooling down it will reset and power on again If this occurs, investigate what is causing the appliance to  overheat
• Thermal Fuse disconnects the appliance permanently in case of overheating (It is nonresettable)

CAUTION

The appliance generates heat during use Precautions must be taken to prevent the risk of burns, scalds, fires, or other damage to persons

CARE AND CLEANING

• The heater requires regular cleaning to ensure trouble-free operation

• Unplug the heater from the mains supply before cleaning

• Ensure that the heater has been allowed to cool down completely before cleaning
  The common cause of overheating is deposits of dust or fluff in the appliance

• Ensure these deposits are removed regularly by unplugging the appliance and vacuum cleaning the air vents and grills

• Use a damp cloth (not wet) to wipe the exterior of the heater to remove dust and dirt

• Never use solutions such as petrol, thinners, or polishing agents

• Ensure the heater is dry before plugging back into the mains supply

• Do not attempt to dismantle the heater

• There are no user-serviceable parts For service or repair, contact an authorised electrical service technician

References

• Goldair Australia
• Goldair Australia
• Wifi – Goldair.nz

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>