Phiaton BT 120 NC Sports Wireless Qualcomm Neckband Bluetooth Earbuds-Complete Features/Instruction Guide

Phiaton BT 120 NC Sports Wireless Qualcomm Neckband Bluetooth Earbuds

Specifications

• COMMUNICATION NETWORK: Bluetooth 4.2
• OUTPUT POWER: Power Class 2
• MAX. COMMUNICATION RANGE: Discoverable within 10 m/33 ft
• FULL CHARGING TIME: 2 Hours
• CALL TIME (NC ON /OFF): 5 Hours /8.5 Hours
• MUSIC PLAY TIME (NC ON/OFF}: 5 Hours/8.5 Hours
• STANDBY TIME (NC ON/OFF): 11.5 Hours/290 Hours
• OPERATING FREQUENCY: 2.4 GHz (2.402 GHz – 2.480 GHz)
• BLUETOOTH PROFILE SUPPORT: HFPv1.7/ HSP v1.2, /A2DP v1.3/ AVRCP v1.6
• AUDIO CODEC: SBC
• BATTERY: Lithium Polymer DC 3.7 V/ 130 MAh
• QUICK CHARGING: 5 minute charging 1 hour use
• MICROPHONE FREQUENCY RANGE: 50-4,000 Hz
• MICROPHONE SENSITIVITY: 42 dB, Support Echo Cancellation and Noise Reduction
• OPERATING TEMPERATURE: -20-45°C
• SIZE: 15.5 (H) x 117.5(W) x 454.7(D) mm/0.6(H)x4.6(W) x 17.9(D) inch
• WEIGHT: 25g (0.055 Ib)
• TYPE: o12 mm Driver Units
• SENSITIVITY: 102 dB
• FREQUENCY RESPONSE: 20 Hz-20 kHz
• IMPEDANCE: 16 Q
• WEIGHT: 0.95 g (0.002 Ib), Mic. for Noise Cancelling

Introduction

Active noise-cancelling headphones decrease 95 per cent of external interference from common noises in offices, airports, and other environments. These audiophile headphones are perfect for music enthusiasts because they block out outside noises. These wireless earphones have been certified as IPX4 splash resistant. Your headphones will be protected against light rain and intense perspiration if they have an IPX4 rating. During the most strenuous workouts, sweatproof technology protects your Bluetooth earbuds secure.

When a call is received, the Phiaton BT 120 NC Noise Cancelling Headphones vibrate to alert you. If you leave the communication range, the vibration will let you know. There are no unpleasant beeps or alert noises to interrupt your listening pleasure. The Phiaton BT 120 NC Wireless Earphones charge quickly. One hour of battery life is obtained after five minutes of charging. With a full charge, you can play for up to 8.5 hours without interruption.

PRODUCT OVERVIEW

WIRELESS EARPHONES WITH ACTIVE NOISE CANCELLING

Thank you for purchasing the PHIATON BT 120 NC

•  Please follow the directions, and read the guidelines carefully before use. Please keep the owner’s guide for future reference.
•  Some functions of the BT 120 NC may not be available when it is paired with certain devices
• The specifications are subject to change without prior notice for quality improvement.

SAFETY AND GENERAL INFORMATION

1. Use a standard USB charging cable (included), with or without a charging adapter. (5V, over 1 A) The adapter Not Included.

2. Lower the volume prior to listening to audio to prevent potential damage to eardrums caused by sudden loud sound.

3. Listening to loud music for extended periods of time may cause hearing damage.

4. Do not store the device in places with a temperature higher than 113 °F/45 °C.

5. This device is IPX4 sweat and water resistant. Please note that it is not waterproof. Please use caution not to oversaturate with moisture or leave excessive moisture on the device as this can damage the internal components. (For more information, refer to the contact us page within our website-phiaton.com.)

6. Do not attempt to disassemble, modify or repair the device.

7. Do not cause shock to the device.

8. Keep out of the reach of children and pets.

9. Do not tug on cords or touch power plugs with wet hands.

10. Do not use the device near microwave ovens or wireless LAN adaptors.

11. When the product is not being used, please keep it in the Charging Speaker Case.

12.  When cleaning the device, use a clean dry cloth to wipe the device clean. (Do not use solvents)

13. To clean the ear tips, remove from earphones, wash with warm water, dry completely and check for debris before reattaching.

14. Replacement ear tips can be purchased from Phiaton Customer Service.
    Email us at SUPPORT@PHIATON.COM

15. Using the device while walking or driving may prevent user from hearing important sounds such as
    signals or alarms and may impose hazardous conditions on yourself or others. Heed caution during use.

16. The radio waves of this device may affect electronic medical devices. If you use any electronic medical device, consult your doctor or the medical device company before you use it.
    Use the BT 120 NC only for its intended purposes. This device cannot be used for purposes related to human safety as it may cause radio interference during operation.

COMPONENTS & FEATURES

COMPONENTS

HOW TO USE THE WIRE CLIP

Insert the wire into the groove on both sides of the wire clip, then move it up and down to find the proper position.

CHARGING

POWER ON/OFF AND STANDBY MODE

POWER ON/OFF

1. -Press and hold the [CALL/POWERĮ Button for 2 seconds to turn the power on.
2. -Press and hold the [CALL/POWER] Button for 3 seconds to turn the power off. (Power will not turn off if there is an incoming call)

When turning the power on/off, there will be a vibration notification. Pairing mode will start once the power is turned on for the first time after purchase. The noise-cancelling function is disabled when the power is off.

CONNECTION STANDBY MODE

• When power is turned on, the BT 120 NC will go into “Connection Standby Mode’ if it does not connect to a Bluetooth Device’ or is in’ Pairing Mode.
• If the ‘Bluetooth Device’ is not connected within 5 minutes while in ‘Connection Standby Mode, the earphones will automatically turn off.

PAIRING WITH A ‘BLUETOOTH DEVICE

PAIRING

Turn on the Bluetooth feature with the ‘Bluetooth Device’ you want to connect with the BT 120 NC. Place the BT 120 NC within 3 feet of the ‘Bluetooth Device’ you want to connect. Press and hold the PLAY Button for over 6 seconds with the BT 120 NC power on to enter Pairing Mode.

• Within the ‘Bluetooth Device”‘ you want to connect, search/select “CURVE BT 120 NC.  If the Bluetooth Device’ requires a PIN CODE or password, enter ‘0000.

• Use the earphones to play music or connect a call.

RE- CONNECTING A DISCONNECTED DEVICE

AUTO CONNECTION

• Once the device has been paired with a ‘Bluetooth Device’ it will automatically connect to a previously connected device once the BT 120 NC power is turned on. The device will not automatically re-connect if Bluetooth was previously disconnected due to the device exceeding the maximum communication range. If such a case, please connect manually when you are within the maximum communication range (33 feet).
• Manual Connection When having entered Connection Standby Mode’ during connection
• Press the CALL/POWER Button or the PLAY Button on the earphone to connect.
• The BT 120 NC will also be connected if you select ‘BT 120 NC’ from the device search list within your ‘Bluetooth Device!

CHECKPOINTS UPON PAIRING

• – Check to see whether the Bluetooth feature is activated within the ‘Bluetooth Device’ you want to connect.
• When selecting the connection device, connect by selecting stereo headset device.
• Music cannot be played when connected through mono headset.
• In order to properly use the Bluetooth feature of this device, the profile (A2DP, HSP, HFP and AVRCP) of the “Bluetooth Device’ you are trying to connect must support the profile of this device. A2DP-Advanced Audio Distribution Profile, HSP- Headset Profile, HFP- Hands Free Profile, AVRCP-Audio/Video Remote Control Profile.
• The device will not operate properly if the profiles are not supported equally. Even when the profiles are supported equally, some features may not properly operate depending on the ‘Bluetooth Device’ specifications.
• To check the detail specifications of this earphone’s profile, refer to ‘SPECIFICATIONS
• For any other inquiries, please contact Phiaton Customer Service.

MULTIPOINT CONNECTION

• WHAT IS A ‘MULTIPOINT CONNECTION’?
  This is a feature where BT 120 NC users can simultaneously connect to two Bluetooth devices.

• MULTIPOINT CONNECTING
  Turn on the Bluetooth feature within the two ‘Bluetooth Devices’ you want to connect with BT 120 NC. Refer to ‘5. PAIRING WITHA BLUETOOTH DEVICE’ to pair the first device with the BT 120 NC. Press and hold the PLAY Button again for 6 seconds to enter Pairing Mode.
  (Here, the first device becomes disconnected) Once in ‘Pairing Mode, connect to the second ‘Blue Device.
  On the first ‘Bluetooth Device’ you want to connect, select ‘BT 120 NC’ again.
  Now, both of the Bluetooth Devices’ will be connected simultaneously, and the second connected device will control 120 NC.
  BT 120 NC will go into Sleep Mode when devices are not connected within two minutes. When trying to connect a device while in Sleep Mode, press any button and it will be in ‘Connection Standby Mode’
  When the BT 120 NC power is turned off and back on, only the second paired device will automatically be connected. When the first paired device is reconnected, then both of the devices will remain connected.

• 

NOISE-CANCELLING FUNCTION

• WHAT IS ‘NOISE CANCELLING?
  Noise Cancelling refers to a technology that reduces noise from mid/low pitched sounds under 1kHz.

• TURNING THE NOISE CANCELLING FEATURE ON/OFF
  With Bluetooth power on, press the Noise Cancelling ON/OFF Button for about 0.5 seconds to start noise-cancelling function, and press again for about 0.5second to stop the noise-cancelling function.  The noise-cancelling function is disabled when the power is off.

• CAUTIONS REGARDS TO THE NOISE-CANCELLING FUNCTION
  Noise Cancelling function cannot be used when the battery is completely discharged. Use while driving or walking will prevent outside Noise, such as signals or alarms, from being heard and may be dangerous to yourself and others. Heed caution during use.
  Noise Cancelling is optimized for mechanical noises from aeroplanes, buses, and subway trains and is not required for use within quiet interior environments.

LISTENING TO MUSIC (PLAY & CONTROL)

PLAYING MUSIC
Shortly press the PLAY Button once to play music from the ‘Bluetooth Device. While music is playing, shortly press the PLAY Button to pause.

VOLUME AND TRACK CONTROL

• Press the ()/O Button to control the volume.
• Press and hold the (+)/) Button for about 1 second to go to the next/previous song.
• After 1 second, you will hear a ‘beep’ tone)
• You can also control volume and track through your Bluetooth Device.

ACCEPTING / MAKING A CALL WHILE PLAYING MUSIC

ACCEPTING A CALL WHILE PLAYING MUSIC

• When you hear the incoming call tone through your earphones or the BT 120 NC vibrates indicating an incoming call, press the CALL/POWER button.
• Once the call has ended, press the CALL/POWER Button to terminate the call. Once the call is terminated, the paused music will play again.

CALL FUNCTION

• ACCEPTING A CALL
  When you hear the incoming call tone through your earphones or the BT 120 NC vibrates indicating an incoming call, press the CALL/POWER Button. (Adjusting Call Volume: to control the call volume, Press the (+)/ () Button)

• ENDING A CALL
  While on a call, shortly press the CALL/POWER Button to end the call.

• REJECTING A CALL
  When you hear the incoming call tone through your earphones or the BT 120 NC vibrates indicating an incoming call, press and hold the CALL/POWER Button for about 1 second. (After hearing the “beep’ signal tone, the incoming call is rejected and the voice guidance “Call ignored” is heard)

• MAKING A CALL
  Please use the call function on your mobile phone. When connecting a call, the vibration is ringing twice for 0.6 seconds.

• CALL STANDBY
  When there is another incoming call while on a call. (Supported only when having applied for this service with your telecom provider) Press and hold the CALL/POWER Button for about 1 second to place the current call on call standby and connect the second call. (Press the CALL/POWER Button again for about 1 second to switch back to the call on standby) Shortly press the CALL/POWER Button to end the current call and connect the second call.

• MAKING A CALL THROUGH VOICE COMMAND.
  (Supported within mobile phones that support the voice command feature)
  While on standby, shortly press the CALL/POWER Button until you hear a beep’ tone.

• SWITCHING BETWEEN THE DEVICE AND MOBILE PHONE
  To switch the call from mobile phone to the headphone, press the CALL Button for 1 second
  

• STOPPING INCOMING CALL VIBRATION
  During an incoming call, you can press the Vol – button for 1 second to stop the vibration notification. You will then only hear the incoming call tone

• DISCONNECT NOTIFICATION
  The BT 120 NC vibrates when you are out of communication range (about 10 m/33 ft.) from the Bluetooth Device. If you move within the communication range within 2 minutes, you will automatically re-connect to your ‘Bluetooth Device. Afterwards, you will need to manually reconnect.

MISCELLANEOUS FEATURES

CHECKING REMAINING BATTERY

• With the power on, shortly press the CALL/POWER button twice to display the remaining battery indicator (LED).

•  For Apple iOS version 5or above, the remaining battery is displayed at the top right side of the screen.
• The Battery Check feature ill not operate while the battery is being charged.
• When the battery charge is under 3%, an alarm will sound. If the device is used, the battery will be completely discharged within several minutes. You will then hear the ‘Power Off’ guidance and the power will automatically turn off.

Battery Life indicated may vary depending on usage conditions.

RESETTING THE DEVICE

To reset to factory settings, while power is off, press the Bluetooth ON/OFF, Play/Pause &Call button and the Vol- button simultaneously for at least 5 seconds.

Frequently Asked Questions

• How can I pair my phiaton Bluetooth device?
  Put your headphones in pairing mode (if you don’t remember how to do this, hold down the Play button for at least two-and-a-half seconds on earphones like the BT 120 NC, and the Call button for the same duration on over-ear headphones like the BT 390).

• What is NC Bluetooth stand for?
  You can listen to music without being bothered by background noise if you utilize the noise cancellation feature. Activate the headset. The voice instruction “Power on” is heard. When you turn on the headset, the noise- cancelling feature is activated automatically.

• How can I connect my phiaton BT 100 NC to my computer?
  Pairing – With the ‘Bluetooth Device’ you want to connect with the BT 100 NC, turn on the Bluetooth feature. – Connect the BT 100 NC to the ‘Bluetooth Device’ you want to connect within 3 feet. – To enter Pairing Mode, press and hold the PLAY Button for more than 2.5 seconds while the BT 100 NC is turned on.

• What is the best way to attach my phiaton headphones?
   Search for and choose ‘BT 110’ under the ‘Bluetooth Device’ you want to connect. Enter ‘0000’ if the ‘Bluetooth Device’ requires a PIN CODE or password. – Use the earbuds to listen to music or make a phone call. To enter Pairing Mode, press the button for more than 4 seconds while the BT 110 is turned off.

• On headphones, what does NC stand for?
  Noise Reduction In terms of headphones Active Noise Cancelling, or ANC, is a technology that helps to reduce background noise in headset speakers. The technology utilized to help decrease background noise in the microphone is referred to as NC, or Noise Canceling.

• On headphones, what does bt stand for?
  Bluetooth is abbreviated as BT. As long as you obtain a proper fit in your ear, sound quality is good.

• What is the procedure for enabling active noise cancellation?
  On your iOS or iPadOS device, open Control Center. Touch and hold the volume slider while wearing your AirPods Max or both AirPods until you see the additional controls. In the lower-left corner, tap the Noise Control icon. Tap Off, Noise Cancellation, or Transparency.

• On Sony headphones, what does the NC button do?
  When you turn on the headset, the noise-cancelling feature is activated automatically. The indicator (green) illuminates when the noise-cancelling function is on. NC Mode B is the noise cancellation mode.

• What are the distinctions between ANC and ENC?
  ANC is a method for lowering noise-making sound by producing an anti-noise- making sound to cancel it out. What is Noise Cancellation in the Environment? ENC is a technique for cancelling unwanted noise using the earphone’s build quality.

• How can I pair my Bluetooth headphones?
  While the Bluetooth headphones are turned off, press and hold the POWER button (for the headphones) for more than 7 seconds. Release the button when the indicator begins to blink rapidly. Pairing mode is activated on the Bluetooth headphones.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>