NEW BRIGHT 61061U Snake Bite Battery Radio Control Monster Truck Instruction Manual

Instruction Manual

CONTENTS

Component Checklist

VEHICLE

Vehicle Features
The ON/OFF Switch controls the main power to the vehicle. To save battery life, always remember to put the switch in the OFF position when not in use. USB Cord Storage Compartment Cover To open the USB Cord Storage Compartment, first use a screwdriver to remove the small screw. Then, push down on the locking tab. Never drive a vehicle while the cover is removed.

Note: The vehicle has working lights.
– When a vehicle is powered ON, eyes will glow and flash.
– When a vehicle is in motion the eyes will glow.
– When the vehicle stops, eyes will glow and flash.

BATTERY

USB Smart Charge Technology
This product is equipped with USB Smart Charge Technology. The built-in “smart chip” can recognize the power output level of your chosen USB charging device. Charge times will vary between charging devices. Charging from a wall outlet with a USB adapter may be faster than charging from a USB port on a computer. Using Advanced USB Power Delivery, the smart chip will charge the vehicle’s internal battery at the fastest speed allowed by your charging device.

Charging the Vehicle
This vehicle is equipped with an internal Lithium-Ion battery that is recharged via USB. ON/OFF Switch must be in the OFF position prior to charging.

1. Locate the ON/OFF switch and USB cord on the underside of the vehicle.
2. Turn the ON/OFF switch to the “OFF” position.
3. Slide open the Storage Compartment cover.
4. Remove the USB cable from the Storage Compartment. (Use care when extending the cord as it is attached to the inside the internal battery). The cord can be plugged into any computer or USB outlet adapter (not included).
5. While charging, the LED under the vehicle will be on. Once fully charged the LED will turn off. Charging is completed in approximately 2 hours depending on the type of charging device you use. Return cord and secure storage lid before operating the vehicle.

TRANSMITTER

Battery Installation

1. Remove the screw to open the Battery Compartment Cover. Pull back on the tab and slide in the direction indicated by the arrow.
2. Insert 2 “AA” size batteries. Make sure the positive (+) and negative (—) markings on the batteries match up to the ones inside the Battery Compartment.
3. Replace the Battery Compartment Cover and replace the screw.

Note: When replacing Transmitter batteries:
Do not mix old and new batteries.
Do not mix alkaline, standard, or rechargeable batteries.
Use alkaline batteries only.

Syncing
This transmitter is equipped with 2.4GHz technology which allows up to 6 vehicles to be used at the same time.
To sync transmitter and vehicle, follow these steps:

1. Install batteries in Transmitter.
2. Turn on Vehicle. Once the batteries are installed and the vehicle is turned on, the Transmitter will sync automatically with the vehicle.

TRANSMITTER

Functions

Driving
This vehicle features a 4×4 pivot drive & steering. The unique drive style may take practice to master. Follow the instructions below for some tips. VERTICAL DRIVING
To raise up onto the back wheels, drive the vehicle in reverse, then quickly push the joystick forward. Once the vehicle is vertical, use the Forward and Left/Right joysticks to continue driving while upright.
ROLLOVER RECOVERY
If the vehicle rolls over, rapidly alternate pushing the joystick FORWARD, then BACKWARD until the vehicle begins to rock. Keep rocking until momentum rolls the vehicle back over.

VEHICLE

Filling Water Tank

1. Locate the water reservoir plug located under the cover on the roof of the vehicle. Pull up the plug tab to open.
2. Using a measuring cup, measure out 1.25oz. (35m1) of water.
3. Place the vehicle on a level surface as shown.
4. Place a funnel in the reservoir hole and slowly pour the water into the tank. Be careful not to spill any water.
5. Remove the funnel and replace the reservoir plug. Press firmly on the plug to make sure it is secure Close the cover.

Note: Do not overfill the tank.
– Overfilling can cause spillage.
– Water spillage can damage electronics.
– Measure water before pouring.
– Use a funnel to minimize spillage.
– Distilled water is recommended to prevent corrosion.

Precautions and Care

SUPPORT

Troubleshooting & Support

Problem – The vehicle does not move or move slowly.
– Make certain there are fresh batteries in the transmitter and that they have been installed in the correct position.
– Are the (+) and (—) markings on the batteries in the same position as the (+) and (—) markings in the Transmitter Battery Compartment?
– Are the metal contact tabs touching, rusty or dirty in the transmitter?
– Has the rechargeable Internal Battery been fully charged? – Make certain that the vehicle ON/OFF switch is in the “ON” position.

Problem – The vehicle moves by itself or exhibits reduced range from the transmitter.
– Make certain there is no outside radio interference in your area. The best way to test this is to take the vehicle as far away from radio towers, electrical lines, or tall buildings as possible to ensure no further radio interference will occur.
Always remove Batteries from the transmitter when not in use.
Do not dispose of batteries in a fire. Leakage, explosion, and personal injury may occur.
Do not attempt jumps or tricks with this vehicle.
Do not attempt to remove the internal battery.
Do not use included USB cord for anything other than its intended purpose.
Always keep the USB cord stored when not in use.
Adult supervision is recommended.

F.C.C. CAUTION:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio technician for help.

OWNER’S MANUAL
Please read and understand all precautions prior to use.
Thank you for choosing a premium New Bright product.

USA Limited WarrantyNew Bright Industries warrants to the original purchaser that this product will be free of defects in materials and workmanship for thirty (30) days from the date of purchase. In the event of such a defect within the warranty period, New Bright will repair or replace the product at our sole discretion. This warranty does not cover damage resulting from unauthorized modifications, accidents, misuse, or abuse.
Should your item have a defect covered under this warranty, first call the toll-free number listed below? Most problems can be resolved in this manner. If necessary, you will be issued a Return Authorization (RA) number and instructions on how to obtain a Product Return Form. The Product Return Form is to be used when returning a product to us (postage pre-paid and insured by the consumer). When returning a defective product, please package the product, the Product Return Form, and a copy of the dated sales receipt as proof of purchase. Be sure to mark the RA number on the Product Return Form. If the product is returned without a dated sales receipt, it will be excluded from coverage under this warranty. Please allow 4 to 6 weeks for delivery of repaired or replacement vehicles (depending on your location). New Bright Industries’ liability for defects in materials and workmanship under this warranty shall be limited to repair or replacement at our sole discretion. In no event shall we be responsible for incidental, consequential, or contingent damages (except in those states that do not allow this exclusion or limitation).

Valid only in the USA & Canada.
Contact New Bright Industries Customer Service Toll-Free at
1-877-NBI-TOYS (1-877-624-8697)
Monday through Friday, 8:00 AM to 5:00 PM Eastern Time U.S. Toy Sales and Marketing Co. Inc.
30260 Oak Creek Drive — 2nd Floor
Wixom MI 48393 1-877-624-8697
http://www.newbright.com/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>