king electric EFW-LD Large Fan Wall Heater Installation Guide
- June 15, 2024
- KING ELECTRIC
Table of Contents
king electric EFW-LD Large Fan Wall Heater
INSTALLATION AND MAINTENANCE
Large Fan Wall Heater
- EFW-LD Low Density Models
- EFW1210-LD / EFW2012-LD / EFW2412-LD
DANGER
ELECTRIC SHOCK OR FIRE HAZARD
READ ALL WIRE SIZING, VOLTAGE REQUIREMENTS, AND SAFETY DATA TO AVOID PROPERTY
DAMAGE AND PERSONAL INJURY
WARNING
READ CAREFULLY – Use the heater only as described in this manual. Any other
use is not recommended and could result in fire, electric shock, and personal
injury. Following these instructions will prevent difficulties that might
occur during the installation and use of the heater. Please study the
instructions first, as they may save considerable time and trouble during use
in addition to providing important safety information. Make sure to save these
instructions for future use.
- Read all instructions before wiring or using this heater.
- This heater is hot when in use. To avoid burns, don’t let bare skin touch hot surfaces. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, boxes, etc., & curtains must be at least 3 feet away from the front and sides of the heater.
- Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
- Do not operate any heater after it malfunctions. Disconnect power at the service panel and have the heater inspected by a qualified electrician for repair before reusing.
- Do not use outdoors
- To disconnect the heater, turn the controls to OFF, and turn OFF power from the main service panel.
- Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock, fire, or damage to the heater.
- To prevent a possible fire, do not block air intakes or exhaust in any manner.
- A heater has hot and arching or sparking parts inside. Do not use it in areas where gasoline, paint, or any other flammable vapors or liquids are stored.
- Use this heater only as described in the manual. Any other use is not recommended by the manufacturer and may cause fire, electric shock, explosion or injury to people and or property.
- This heater includes a Smart limit protection that shuts down the heater in the event of excessive overheating. To reset the heater: Turn OFF the Power, Wait 10 Minutes for the limit to reset, and then Turn Power Back On.
EFW INSTALLATION INSTRUCTIONS
CAUTION!
Turn OFF all electrical power to install the heater
Rating Label Location
ELECTRIC SHOCK OR FIRE HAZARD
READ ALL WIRE SIZING, VOLTAGE REQUIREMENTS, AND SAFETY DATA TO AVOID PROPERTY
DAMAGE AND PERSONAL INJURY
Selecting a location for your heater:
Do NOT install less than 6 inches from vertical side walls or open edge of the door. The heater must have unrestricted airflow. Do Not select a location where it is likely to be blocked by furniture, curtains, etc. Be sure the location selected allows sufficient space for the heater as shown below in Table 1. Do NOT locate the heater in areas where combustible vapors, gases, flammable liquids, or excessive lint, dust or moisture is present.
Zero clearance to insulation
KO location as mounted in wall.
The wire & breaker sizing chart will give a general rule of installation size. Consult an electrician if not knowledgeable about wiring codes.
Wire and Breaker Sizing:
WIRING : Branch Circuit Connection
- Connect the heater only to the voltage, amperage and frequency specified on the nameplate.
- Remove the grill by loosening and removing the four screws on the side of the front panel.
- Detach the interior from the wall can by removing the four screws along each side of the interior. Remove the interior by tilting it away from the wall can to release the bottom edge.
- Wiring procedures and connections shall be by all National and local codes having jurisdiction.
- A knockout of 1/2 inch conduit size (7/8 inch) is provided in the back and side of the heater for power to enter. Provide proper strain relief connectors (not included) for your wire entering the wall box.
- Install a wall box a minimum of 6″ from vertical side walls & 4″ above the floor (For best performance 10″ above the floor is recommended).
- Secure the wall box to the 2 x 4 studs using the (2) holes on the side of the wall box. Secure to a wall stud on the opposite side if required. Make electrical connections per the wiring diagram. Supply wires L1 and L2 can be connected to the red or black wires on the heater – the order does not matter. Attach the field ground wire to the green screw or pigtail. When installing a built-in thermostat red always connects to the supply wires and black to the heater.
- Reinstall interior. Make sure electrical wires are clear on the interior sides. Fasten the interior and then the grill with the screws provided.
- Test the unit by turning the thermostat up past room temperature. You will see a puff of smoke as the elements are energized and the fan turns on. This is a normal burn-off of manufacturing lubricants and will dissipate in 5 minutes.
- The heater will continue to run until the room temperature you set is reached and then turn itself off until the temperature drops again.
INSTALLATION AND WIRING
SMART LIMIT PROTECTION AND MAINTENANCE
Heater Safety Limit Tripped?
This heater is equipped with a thermal overload Smart Limit Protection which
disconnects elements and motor in the event normal operating temperatures are
exceeded. If thermal overload trips due to abnormal
operating temperatures, thermal overload shall remain open until manually
reset by turning the heater OFF for fifteen minutes. Inspect for any objects
on or adjacent to the heater that may cause high temperatures.
After inspecting the heater, keep the power to the heater off for 15 minutes
to reset the SLP thermal protector. If the SLP thermal protector shuts the
heater off again, immediately turn the heater OFF at the circuit breaker and
inspect the heater for possible fan motor failure or dirt and lint on the
heating element. Repeat the starting procedure.
DO NOT TAMPER OR REMOVE THIS THIS DEVICE
Maintenance & Warranty Information:
The high quality and superior design of this heater will provide years of
trouble-free performance. Each year the heater should be checked and cleaned
for lint and dust accumulation. We recommend using a soft bristled brush such
as a paint brush to assist in removing contaminants from the heater.
Warranty
Limited One-Year Warranty:
King Mfg. Co. will repair or replace without charge any King product found to
be defective or malfunctioning during the first year of purchase to the
original owner.
KING ELECTRIC MFG CO
9131 10TH AVENUE SOUTH
SEATTLE, WA 98108
PH :206 762 0400
FAX : 206 763 7738
www.king-electric.com
DO NOT RETURN PRODUCT
Are you experiencing difficulties?
We’re Here to Help!
Call Us Toll Free at:
1-800-603-5464
(Select Option 2 from the Menu) 7:00 am -3:30 pm PST Mon-Fri Or email us at
tech@king-electric.com
Please have the following information available:
Supply Voltage Heater Model Number
Remote or Inbuilt Thermostat?
Date of Installation
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>