Schneider Electric APVS9601 Easy UPS SNMP Card User Manual
- June 3, 2024
- Schneider Electric
Table of Contents
User Manual Easy UPS
SNMP Card APVS9601
Important Safety Information
Read the instructions carefully and look at the equipment to become familiar
with the device before trying to install, operate, service or maintain it. The
following special messages may appear throughout this document or on the
equipment to warn of potential hazards or to call attention to information
that clarifies or simplifies a procedure.
The addition of this symbol to a Danger or Warning product safety label
indicates that an electrical hazard exists that will result in personal injury
if the instructions are
not followed.
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or
death.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to physical injury.
Product Description
Integrated with SchneiderUPS software, devices with the SNMP Card installed
can be monitored and controlled in the LAN. These devices can manage using
SNMP Protocol versions 1, 2c and 3 standards.
APVS9601 SNMP Card:
-
Provides support for SchneiderUPS Network Shutdown.
-
Supports using a Dynamic Host Configuration Protocol (DHCP) to provide the network (TCP/IP) values of the NMC.
Devices in which you can install the SNMP Card
The SNMP Card can be installed in any compatible device that has an Intelligent Card Slot, including: -
Easy UPS On-Line: SRV series UPS
Package Contents
The packaging is recyclable; save it for reuse or dispose of it properly.
Disclaimer
Schneider Electric is not responsible for damage sustained during reshipment
of this product.
The SNMP Card is sensitive to static electricity. When handling the SNMP Card,
touch only the end plate while using one or more of these electrostatic-
discharge devices (ESDs): wrist straps, heel straps, toe straps, or conductive
shoes.
Please recycle
The shipping materials are recyclable. Save them for later use, or dispose of
them appropriate.
Product Overview
Front Panel
| 1 | Sensor port | Connects SNMP card to temperature or smoke sensor. |
|---|---|---|
| 2 | 10/100 Base-T connector | Connects SNMP card to the Ethernet network. |
| 3 | Status LED | See “Status LED”. |
Status LED
| Color LED | Condition | Description |
|---|---|---|
| 100M LED (Green) | Flash | Port is operating at 100Mbit/s |
| Off | Card is not connected to the network | |
| 10M LED (Yellow) | Flash | Port is operating at 10Mbit/s |
| Off | Card is not connected to the network |
Specifications
Physical| Dimensions with package Width x Height x Depth| 168 mm (6.61in) x 42
mm (1.65in) x 132 mm
(5.2in)
---|---|---
Dimensions without Width x Height x Depth package| 47 mm (1.85in) x 25 mm
(0.98in) x 80 mm
(3.15 in)
Weight with package| 0.3 kg (0.66 lb)
Weight without package| 0.11 kg (0.24 lb)
Temperature| Operating| 0 to 40°C (32 to 104°F)
Storage| -15 to 50°C (5 to 122°F)
Humidity| Operating| 0 to 95% relative humidity, non-condensing
Supported
Protocol| Network| Auto-sense 10/100 Mbps Fast Ethernet RJ45
LAN Connector
Network Protocol| “5 II IP• SNMP-VI, SNMP-V2, SNMP- V3
SNIVIP MIB| RFC1213, RFC1628
Installation
Install the SNMP card
You do not need to turn off power to install the SNMP Card in a supported Easy
UPS.
The SNMP Card is sensitive to static electricity. When handling the SNMP Card,
touch only the end plate while using one or more of these electrostatic-
discharge devices (ESDs): wrist straps, heel straps, toe straps, or conductive
shoes.
For the location of the UPS Intelligent Card Slot, see the UPS User Manual.
- Remove the cover of Intelligent Card Slot on the back of the UPS and retain the screws.
- Slide the card into the open slot and secure with the screws from step 1. (See below chart)
- Connect a network interface cable to the 10/100 Base-T network connector (RJ-45) on the SNMP Card.
When the network interface cable is connected, the SNMP Card will attempt to
obtain an IP address via DHCP. See “Configuration methods” on page 6.
Configure the SNMP Card See “Quick Configuration” on page 6.SNMP Card
APVS9601
Quick Configuration
Configuration Method
- Please install SchneiderUPS monitoring software in your PC. After software is installed successfully, it will pop up a plug icon in the tray. Select “SNMP manager” by clicking right button of the mouse.
- Enter specific IP address to search all SNMP devices in LAN. (The SNMP manager will automatically collect the IP address from sever by default via a DHCP server. It will apply default IP address of 192.168.102.230, default subnet mask as 255.255.255.0, and default gateway as 192.168.102.254 without a DHCP server.
- You can modify IP setting, online upgrade, password management, and static trap address setting in SNMP Manager interface. It is necessary to enter password for any medications. The default password is 12345678.
Monitoring
- After all setting is complete, select “Open Monitor” by clicking right button of the mouse. NOTE: For enhanced security, change the SNMP version to V3 in System management and change the default password.
- Then, it will open the monitor view. Refer to below chart.
Please check Schneider UPS monitoring software manual in the install location or in the CD.
Schneider Electric Worldwide Customer Support
Customer support for this or any other Schneider Electric product is available at no charge in any of the following ways:
-
Visit the Schneider Electric website to access documents in the Schneider Electric Knowledge Base and to submit customer support requests.
– www.apc.com (Corporate Headquarters)
Connect to localized Schneider Electric websites for specific countries, each of which provides customer support information.
– www.apc.com/support/
Global support searching Schneider Electric Knowledge Base and using e-support. -
Contact the Schneider Electric Customer Support Center by telephone or e-mail.
– Local, country specific centers: go to www.apc.com/support/contact for contact information.
For information on how to obtain local customer support, contact the Schneider Electric representative or other distributor from whom you purchased your Schneider Electric product.
© 2018 Schneider Electric. The Schneider Electric logo is owed by Schneider
Electric Industries
S.A.S., or their affiliated companies. All other trademarks are property of
their respective owners.
EN 990-91199
09/2018
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>