aigostar 8433325184926 Stand Fan Instruction Manual

aigostar 8433325184926 Stand Fan

WARNING
Read Rules for Safe Operation and Instructions Carefully.

1. If the supply cord is damaged, it must be replaced by manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
2.  Household Indoor use only.
3.  To protect against the risk of electrical shock, do not immerse the unit, cord or plug in water or other liquid.
4.  This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
5. When the appliance is not in use and before cleaning, unplug the appliance from the outlet.
6.  When the fan was assembled, the rotor blade guard shall not be taken off anymore.
7.  Correct Disposal of this product This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

RULES FOR SAFE OPERATION

1. Never insert fingers, pencils, or any other object through the grille when fan is running.
2. Disconnect fan when moving from one location to another.
3. Be sure fan is on a stable surface when operating to avoid overturning.
4. DO NOT use fan at window, rain may create electrical hazard.
5. Household use only

PARTS NAME

1. Front grill
2. Fan blade
3. Tighten
4. Loosen
5. Spinner
6. Plastic nut
7. Rear grill
8. Motor shaft
9. Clutch knob
10.  Motor housing
11. Piano switch
12. Thumb screw
13. Internal Pole
14. Fasten
15. Height adjustment ring
16. Extension Pole
17. Stand ornament
18.  tand

ASSEMBLY OF CROSS STAND & COLUMN UNIT

1. Loosen 4 sets of screws, washers and spring washers which are fitted in the center section on the stand and assembly the extension pole onto the base enclosure with these screws originally. (Fig.1)

2. Loosen the height adjustment ring, lift the internal pole to the max height and prevent the internal pole from slipping into the extension pole, then screw out the height adjustment ring. (Fig.2)

3. To attach the stand ornament (cover for the stand), slide the stand ornament down the extension pole. (Fig.3)

4. Reattach the height adjustment ring. (Fig.4)

5. From the extension pole loosen the height adjustment ring and adjust the internal pole to the desired height. (Note: If you can’t find the internal pole, it slides inside the extension pole. You can pull it out from the extension pole.) (Fig.5)

6. To attach the head unit to the internal pole, loosen the thumb screw on the bottom of
   the head unit. Place the head unit on the internal pole and tighten the thumb screw inalignment with the groove on the internal pole. (Fig.6)

7. Fasten tight

8. Adjustment ring

9. Stand ornament

10.  screws

11. Stand

12. Loosen

13. Tighten

14. Loosen

15. Annular groove

16. Thumb screw

17. Mounting hole

GRILL & FAN BLADE ASSEMBLY

1. Unscrew the spinner clockwise (or take the spinner out from the bag) and the plastic nut counterclockwise to remove both of them. Fix the rear grill to the motor thentighten the plastic nut again. (Fig. 7)
2. Insert the blade into shaft, and make sure the rotor shaft pin is fitted into groove of the blade. Turn the spinner counterclockwise to tighten the blade. (Fig. 8)
3. Fasten the front grill and the rear grill by the grill clip and then tighten the fan grill locking screw and nut. (Fig. 9)

OPERATING INSTRUCTION

1. Speed is controlled by the Piano switch: 0—Off 1—Low 2—Medium 3—High
2. To make/stop the fan head oscillate. Push down/pull up the clutch knob.
3. To adjust the air flow upward or downward, push the grilles lightly to the desired direction.
4. The height of the fan can be adjusted by loosening the height adjustment ring, carefully raising or lowering the fan and firmly re-tightening the height adjustment ring.

MAINTENANCE INSTRUCTION

The fan requires little maintenance. Do not try to fix it by yourself. Refer it to qualified service personnel if service is needed.

1.  Before cleaning and assembling, fan must be unplugged.
2.  To ensure adequate air circulation to the motor, keep vents at the rear of the motor free of dust. Do not disassemble the fan to remove dust.
3.  Please wipe the exterior parts with a soft cloth soaking a mild detergent.
4.  Do not use any abrasive detergent or solvents to avoid scratching the surface. Do not use any of the following as a cleaner: gasoline, thinner.
5.  Do not allow water or any other liquid into the motor housing or interior parts.
6. Be sure to unplug from the electrical supply source before cleaning.
7. Plastic parts should be cleaned with a soft cloth moisten with mild soap. Thoroughly remove soap film with dry cloth.

DISPOSAL： Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.

WARRANTY: 2 YEARS

SAMSPARTY SL CL CABAÑA 78,45210 YUNCOS TOLEDO,ESPANA
B45824786
http://www.aigostar.com
Made in P.R.C

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>