vtech VM819 Video Baby Monitor User Guide

: June 3, 2024
: vtech

Table of Contents

VM819 Video Baby Monitor
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VM819 Video Baby Monitor

32

VM819
Video Baby Monitor
Quick start guide

Channels

LCD

range

Important safety instructions

The applied nameplate is located at the bottom of the baby unit’s base.

voltage points or create a short circuit. Never spill liquid of any kind on the product.

When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:
1. Follow all warnings and instructions marked on the product.
2. Adult setup is required. 3. CAUTION: Do not install the baby unit at a height
above 2 metres. 4. This product is not a substitute for adult supervision of the
infant. Supervising the infant is the responsibility of the parent or carer. This product could cease operating, and therefore you should not assume it will continue working properly for any given period of time. Further, this is not a medical device and should not be used as such. This product is intended to assist you in supervising your baby. 5. Do not use this product near water, for example, near to a bath, sink, swimming pool or shower.
6. CAUTION: Use only the battery provided. There may be a risk of explosion if a wrong type of battery is used for the parent unit. The battery cannot be subjected to high or low extreme temperature and low air pressure at high altitude during use, storage or transportation. Disposal of battery into fire or a hot oven, or mechanically crushing or cutting or the battery can result in an explosion. Leaving the battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid of gas. Battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
7. Use only the adaptors included with this product. Incorrect adaptor polarity or voltage can seriously damage the product. Use only adaptors and battery listed below.

18. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.
19. You should test the sound reception every time you turn on the units or move one of the components.
20. Periodically examine all components for damage. 21. There is a very low risk of privacy loss when using
certain electronic devices, such as baby monitors, cordless telephones, etc. To protect your privacy, make sure the product has never been used before purchase, reset the baby monitor periodically by powering off and then powering on the units, and power off the baby monitor if you will not use it for some time. 22. Children should be supervised to ensure that they do not play with the product. 23. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
SAVE THESE INSTRUCTIONS Cautions 1. Use and store the product at a temperature between
0oC and 40oC. 2. Do not expose the product to extreme cold, heat
or direct sunlight. Do not put the product close to a heating source.

Power adaptor information: Parent unit output: 5V DC 1A VTech Telecommunications Ltd. Model: VT05EEU05100 (EU), VT05EUK05100 (UK) Baby unit output: 6V DC 400mA VTech Telecommunications Ltd. Model: VT05EEU06040 (EU), VT05EUK06040 (UK)
Rechargeable battery information: Zhuhai Great Power Energy Co., Ltd. Li-ion battery, 3.6V, 2600mAh, 9.36Wh; Model: ICR18650-2.6Ah-3.6V-1S1P 8. The power adaptors are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. 9. For pluggable equipment, the socket-outlet should be installed near the equipment and should be easily accessible. 10. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 11. Do not cut off the power adaptors to replace them with other plugs, as this causes a hazardous situation. 12. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped. 13. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company. 14. Do not overload wall outlets or use an extension cord. 15. Do not place this product on an unstable table, shelf, stand or other unstable surfaces. 16. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat source.

3. Batteries should not be exposed to excessive heat such as bright sunshine or fire.

Warning–Strangulation Hazard–Children

have STRANGLED in cords. Keep this

cord out of the reach of children (more

than 3 ft (0.9m) away). Do not remove

this tag.

5. Never place the baby unit(s) inside the

baby’s cot or playpen. Never cover the

baby unit(s) or parent unit with anything such as a towel

or a blanket.

6. Other electronic products may cause interference

with your baby monitor. Try installing your baby

monitor as far away from these electronic devices

as possible: wireless routers, radios, cellular

telephones, intercoms, room monitors, televisions,

personal computers, kitchen appliances and

cordless telephones.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless

devices):

Wireless Technology Research, LLC (WTR), an independent

research entity, led a multidisciplinary evaluation of the

interference between portable wireless devices and

implanted cardiac pacemakers. Supported by the U.S. Food

and Drug Administration, WTR recommends to physicians

that:

Pacemaker patients

· Should keep wireless devices at least six inches from the

pacemaker.

· Should NOT place wireless devices directly over the

pacemaker, such as in a breast pocket, when it is turned

ON.

WTR’s evaluation did not identify any risk to bystanders with

pacemakers from other persons using wireless devices.

Electromagnetic fields (EMF)

This VTech product complies with all standards regarding

electromagnetic fields (EMF). If handled properly and

according to the instructions in this user’s manual, the

product is safe to be used based on scientific evidence

available today.

17. Never push objects of any kind into this product through the slots because they may touch dangerous

What’s in the box
Quick start guide
1 Connect the baby monitor
NOTES · The rechargeable battery in the parent unit is
built-in. · Use only the power adaptors supplied with this
product. · Make sure the baby monitor is not connected to
a switch-controlled electric outlet. · Connect the power adaptor in a vertical or floor
mount position only. The adaptor prongs are not designed to hold the weight of a baby monitor, so do not connect them to any ceiling, under-thetable, or cabinet outlets. Otherwise, the adaptor may not properly connect to the mains. · Make sure the parent unit, the baby units and the power adaptor cords are out of reach of children.

Strangulation Hazard
Keep this cord out of reach of children. The cord needs to be at least three feet away from the child at all times. Do not use with an extension cord. Do not remove this tag.
Risque d’étranglement Éloignez ce cordon des enfants. Le cordon doit se trouver à au moins trois pieds d’un enfant et ce, en tout temps. N’utilisez pas de rallonge. Ne retirez pas cette étiquette.
Riesgo de estrangulación Mantenga este cable fuera de la alcance de los niños. Este cable debe estar por lo menos tres pies fuera de la alcance del niño en todo momento. No lo use con una extensión inalámbrica. No quite esta etiqueta.

Power requirements Parent unit: 3.6V, 2600mAh, 9.36Wh Li-ion battery Parent unit power adaptor: Output: 5V DC @ 1A Baby unit power adaptor: Output: 6V DC @ 400mA

conditions at the time of use.

Nominal effective Actual operating range may vary according to environmental

2.8″ Colour LCD (QVGA 320×240 pixel)

Transmit frequency Baby unit: 2405 – 2475 MHz Parent unit: 2405 – 2475 MHz Maximum power used by the transmitter: 0.1W (100mW)

Strangulation Hazard
Keep this cord out of reach of children. The cord needs to be at least three feet away from the child at all times. Do not use with an extension cord. Do not remove this tag.
Risque d’étranglement Éloignez ce cordon des enfants. Le cordon doit se trouver à au moins trois pieds d’un enfant et ce, en tout temps. N’utilisez pas de rallonge. Ne retirez pas cette étiquette.
Riesgo de estrangulación Mantenga este cable fuera de la alcance de los niños. Este cable debe estar por lo menos tres pies fuera de la alcance del niño en todo momento. No lo use con una extensión inalámbrica. No quite esta etiqueta.

Frequency control Crystal controlled PLL synthesizer

Technical specifications

Basic operation – Parent unit

Overview – Baby unit

Use the menu

Adjust parent unit speaker volume

Zoom

Press MENU to enter the menu, or save a setting. You can use the parent unit for advanced settings or operations, such as to play or stop the baby unit’s lullaby, or to adjust the baby unit’s sound sensitivity.

· Press VOL+ / VOL- to adjust your parent unit speaker volume.

1. Press MENU when in idle mode. 2. Choose . 3. Press or to choose (Zoom in) or

While in the menu:
· Press or to scroll among the menu options.
· Press or to select an item. · Press SELECT to confirm your
selection.
· Press TALK/EXIT to exit the menu and return to live view.

Submenu Main menu

(Zoom out), then press SELECT to

3

confirm your selection.

4

5

6

8

1

7

9

2

Talk to your baby unit
Press and hold TALK and speak to your parent unit. Your voice is transmitted to the baby unit. When you finish talking, release TALK to hear your baby again.

Turn off the screen
Press POWER/LCD OFF to switch off the screen. You can still hear sounds from the baby unit.

Press and hold

Tip
· Press any key on the parent unit to turn the screen on again.

Overview – Parent unit

1

2

10

3

11

4

9

5

6

7 8

1 Battery LED light

5 LINK LED light

7 POWER/LCD OFF

2 3-level sound indicator light

·

On when the parent unit is linked to the baby

8

Microphone

3 · Arrow keys

unit.

9 Power jack

·

VOL+ / VOL-

·

Flashes when the link to the baby unit is lost.

10

RESET

4 MENU/SELECT

6 TALK/EXIT

· Force reboot the parent unit.

·

Press and hold to talk to the baby unit.

11

Speaker

· While in a submenu, press to exit.

10

1 PAIR hole · The parent unit and baby unit(s) provided are already paired.
2 POWER LED light
3 Microphone
4 Camera

5 Infrared LEDs

6 Light sensor

7

ON/OFF switch

8 Speaker

9 Power jack 10 Slots for wall mounting

1 Connect the baby monitor (cont’d)

Charge the parent unit battery
When you have connected and turned the parent unit on, the battery charges automatically.
Notes
· Before using the baby monitor for the first time, charge the parent unit battery for 12 hours. When the parent unit battery is fully charged, the battery icon becomes solid .
· It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time, turn the parent unit off while charging.
· The standby time varies depending on the sensitivity level you set, your actual use and the age of the battery.

The battery icon indicates the battery status (see the following table).

Battery indicators

Battery status

Action

The screen displays . The light flashes.
The battery icon becomes solid .

The battery has very little Charge without interruption (about power and may only be used 30 minutes). for a short time.
The battery is fully charged. To keep the battery charged, connect it to AC power when not in use.

2 Power on or off the baby monitor

Slide the ON/OFF switch to power on or off your baby unit.

Press and hold POWER to power on or off your parent unit.

3 Positioning the baby monitor

Caution
· Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the baby’s crib or playpen.

13mfte(1trme)

1 metre

< 1 metre

13mft e(1tmre)

<<1 m3fte(1trme)

Note
· To avoid interference from other electronic devices, place your baby monitor at least 1 metre away from devices such as wireless routers, microwaves, mobile phones and computers.

Caution
· The default volume of your parent unit is level 3, and the maximum volume is level 5. If you experience feedback from your baby monitor while positioning:
– Make sure your baby unit and parent unit are more than 1 metre apart, OR
– Turn down the volume of your parent unit.

Caution
· Please avoid covering the illustrated area during operation.

Press and hold

Power off Power on

4 Status check
Once you power on both your baby unit and parent unit, your parent unit displays image from the baby unit, and the LINK LED light turns on.
The baby unit’s POWER LED light turns on.

Parent unit icons

Status icons

Sub-menu icons Main menu icons

Status icons

Connection status · or displays when strong signal strength is detected between the baby
unit and the parent unit. · or displays when moderate or low signal strength is detected between
the baby unit and the parent unit.
Current view status · Displays the baby unit number of the baby unit being viewed.
Zoom · Displays when the current image on the parent unit has been zoomed in.
Night vision · Displays when the baby unit being viewed has activated the night vision
feature.
Talkback · Displays when the parent unit is talking to the baby unit.
Lullaby · Displays when a lullaby is playing.

Night light · Displays when the baby unit’s night light is turned on.

Mute alert · Displays when the parent unit speaker volume is set to zero. · Displays when the parent unit is talking to the baby unit.

or

Real-time temperature · Displays the real-time temperature detected by the baby unit in Fahrenheit (oF)

or Celsius (oC) (e.g. 57 oF or 14 oC).

Battery status

·

animates when the battery is charging.

· displays solid when the battery is fully charged.

· displays when the battery is low and needs charging.

Main menu icons
Main Sub-menu menu
Zoom · Zoom in and out of the video displayed from the baby unit.

Settings

Temperature

Screen off timer · The parent unit display will turn off to conserve energy after your chosen
amount of time inactive.
Brightness · Adjust the parent unit’s LCD screen brightness level.

· Turn on/off temperature alert tone.
· Set the parent unit to beep whenever the room temperature detected by the baby unit falls outside of the set temperature range.

· Set the minimum/maximum temperature.

· Set temperature display in Fahrenheit (oF) or Celsius (oC).

Parent unit icons (cont’d)
Sub-menu icons Main menu icons

Main menu icons
Main Sub-menu menu
Sound Detection
VOX (Voice Activated Alert) Sensitivity · You can choose to hear sounds from the baby unit all the time, or to only
hear sounds that exceed a certain level. Adjust the microphone sensitivity of your baby unit, where the higher the sensitivity level, the more sensitive the baby unit is in detecting sounds that will transmit to the parent unit. See Sound sensitivity and sound activation section.

Lullaby

Sound-activated screen · When it is on, and the baby unit detects no sound, the parent unit screen
stays off to save power. Once a sound is detected, the parent unit screen and speaker turns on automatically, and you can see and hear your baby. The parent unit will then turn off again after 50 seconds of no sound detection.
Note · When the parent unit screen is off and it receives alerts, for example, link
lost between parent unit and baby unit or battery is low, the parent unit screen and speaker will turn on for 10 seconds.
Lullaby volume · Adjust the baby unit’s speaker volume when playing the lullaby.

· Select one of the four melodies to play, or stop a lullaby.

Warning icons and messages

Battery low at Parent Unit

The battery is empty and needs to be recharged. Operation is in progress.

Temperature too high

The temperature detected by the baby unit is higher than the desired temperature alert range.

Temperature too low

The temperature detected by the baby unit is lower than the desired temperature alert range.

The parent unit is searching for baby units or the link between the baby unit and the parent unit is lost, for example, due to out of No Link to Camera range.

The parent unit is connected to AC power.

Parent Unit Indication Lights

LINK

· On when the parent unit is linked to the baby unit. · Flashes when the link to the baby unit being viewed is lost.

· On when the parent unit is connected to AC power, or the battery is charging.
· Flashes when the parent unit battery is low and needs charging.
· Off when the parent unit is disconnected from AC power.

Frequently asked questions

Below are the questions most frequently asked about the baby monitor.

Why does the baby monitor not respond normally?

Try the following (in the order listed) for a common cure: 1. Disconnect the power to the baby units and the parent unit. 2. Wait a few seconds before connecting power back to the baby units and the parent unit. 3. Turn on the baby units and the parent unit. 4. Wait for the parent unit to synchronize with the baby units. Allow up to one minute
for this to take place.

Why doesn’t the baby unit and parent unit power-on light illuminate when the units are switched on?

Perhaps the parent unit is not connected to power. Insert the appliance plug into the parent unit and insert the adaptor in a wall socket. Then, press and hold POWER to switch on the parent unit and to establish connection with the baby unit.
Perhaps the baby unit is not connected to power. Insert the appliance plug into the baby unit and insert the adaptor in a wall socket. Then, slide the ON/OFF switch to ON to switch on the baby unit and to establish connection with the parent unit.

Why doesn’t my parent Make sure the power is not controlled by an electronic wall switch.

unit charge while connected to AC power?

You may have used the battery for a long time. See Warranty for repair/replacement.

Why is my screen in black and white?

The screen is in black and white during night-time or in a dark room when the night vision feature is activated. This is normal.

Why do I get glare or blurry display on my screen when viewing my baby at night?

During night-time or in a dark room, the surrounding and other interfering factors, like lighting, objects, colours and backgrounds may affect the image quality on your parent unit screen. Adjust the baby unit angle or place the baby unit at a higher elevation to prevent glare and a blurry display.

Why does the baby monitor produce a feedback?

The parent unit and baby units may be too close to each other. · Move the parent unit away from the baby units until the noise stops; OR · Turn down the volume of your parent unit.

Why does the parent unit beep?

The baby unit may be out of range. Move the parent unit closer to the baby unit (but not less than 1 metre).

The parent unit may not have enough battery for the parent unit to perform normally. Charge the battery in the parent unit until the battery icon becomes solid .

The temperature of your baby’s room may be too high or too low.

Why does the parent unit react too quickly to other sounds?

The baby unit also picks up other sounds than those of your baby. Adjust the VOX sensitivity level to a lower level or lower the parent unit speaker volume. See Adjust the sound sensitivity of the baby unit.

Why don’t I hear a sound/Why can’t I hear my baby cry?

The parent unit speaker volume may be too low. See Adjust parent unit speaker volume to increase the volume.
You may have set a low VOX sensitivity level. See Adjust the sound sensitivity of the baby unit to set to a higher level.

Why can’t I establish a connection? Why is the connection lost every now and then? Why are there sound interruptions?

The baby units may be out of range. Move the parent unit closer to the baby units (but not less than 1 metre).
Other electronic products and wireless products may cause interference with your baby monitor. Try installing your baby monitor as far away from these devices as possible.

Customer service and product warranty

PRODUCT REGISTRATION
Visit www.vtech.co.uk/clubvtech/login to register your VTech product
By joining the VTech Club you can also enter competitions, find out about news and events, seek expert advice for parents
and let your kids play fun learning games and activities.

PROD

ONE YEAR
UCT WARR

ANTY

PRODUCT WARRANTY
Thank you for choosing this quality product from VTech.

1. The product detailed above is covered by a one year warranty from the date of purchase, against any defects in materials or workmanship.

2. The product may be returned to the place of purchase. Alternatively the product can be returned to VTech Electronics Europe Plc (see address below), with proof of purchase, without proof of purchase no replacement will be provided.

3. VTech Electronics Europe Plc will examine the product and if it is found to be defective due to faulty materials or workmanship, will replace the product at their discretion.

4. If the product covered by this warranty is damaged due to misuse, modification or unauthorized repair, or because of faulty batteries, battery discharge or incorrect electrical connections, then this warranty becomes void.
5. This warranty is personal to the original purchaser and is not transferable.

6. Breakages to the LCD screen are not covered by the warranty.

7. Products returned to VTech Electronics Europe Plc, should be sent to the address shown below and packed carefully to avoid damage in transit. Please do not include batteries or adaptors. Please include details of the fault together with your name and address, contact phone number and/or email address.

8. To keep an online record of your warranty, please register your product online at www.vtech.co.uk/clubvtech

VTech Electronics Europe Plc, c/o XPO Logistics, Warehouse 350, Cat & Fiddle Lane, West Hallam, DE7 6HE
THIS WARRANTY IS OFFERED AS AN EXTRA BENEFIT AND DOES NOT AFFECT CONSUMERS’ STATUTORY RIGHTS.

This warranty is valid for the UK and Ireland only. For products purchased outside the UK and Ireland, please contact your local distributor or place of purchase.

IMPORTANT Please retain this booklet with your sales receipt as proof of the date of purchase.
Customer Service Please call our Consumer Services Department on 03306 780149 (from UK) or +44 3306 780149 (outside UK) and a service representative will be happy to help you.

Sound sensitivity and sound activation

Adjust the sound sensitivity of the baby unit
You can choose to hear sounds from the baby unit all the time, or to only hear sounds that exceed a certain level. Use the parent unit to adjust the baby unit microphone sensitivity. The higher the sensitivity level, the more sensitive the baby unit will be in detecting sounds that transmit to the parent unit. The VOX sensitivity level is preset to the highest level.

VOX Sensitivity level
Description

Highest

High

Medium

Low

Lowest

The parent unit speaker is constantly on, and you will hear all sounds (including background noises) from your baby’s room.

The parent unit speaker turns on for soft babbling and louder sounds from your baby. It remains quiet when your baby sleeps soundly.

The parent unit speaker turns on for loud babbling and louder sounds from your baby. It remains quiet when your baby makes soft sounds.

The parent unit speaker turns on for crying and louder sounds from your baby. It remains quiet when your baby makes soft sounds.

The parent unit speaker turns on for loud crying or screeching sounds from your baby. It remains quiet when your baby makes soft sounds.

Sound activated screen
With sound activation turned on, the parent unit screen remains off to save power when the baby unit detects no sound. Once the baby unit detects sounds that are louder than the chosen sound sensitivity level, the parent unit screen turns on automatically. It will then turn off again after 50 seconds of no sound detection.

Dim mode
The dim mode helps save parent unit power. Your parent unit display will turn off automatically after 10 minutes of inactivity, when no keys are pressed or alerts are received from the baby unit.
10 mins inactive

Press any button
Note
· While the screen is turned off, any keypress or alert message will trigger the screen to return to the preset brightness level. After 10 minutes of inactivity, it will resume to dim mode.

Night vision

The baby unit has infrared LEDs that allow you to see your baby clearly at night or in a dark room. When the baby unit being viewed detects low light levels, the infrared LEDs are switched on automatically. The images from the baby unit are in black and white, and appears on the screen.
Notes
· It is normal to see a short white glare on your parent unit screen as the baby unit adapts to the dark environment.
· When the infrared LEDs are on, it is normal for the images to be in black and white.
Tip
· Depending on the surrounding and other interfering factors, like lighting, objects, colours and backgrounds, the display resolution may vary. Adjust the baby unit angle or place the baby unit at a higher elevation to prevent glare and a blurry display.

Disposal of batteries and product
The crossed-out wheelie bin symbols on products and batteries, or on their respective packaging, indicates they must not be disposed of in domestic waste as they contain substances that can be damaging to the environment and human health.
The chemical symbols Hg, Cd or Pb, where marked, indicate that the battery contains more than the specified value of mercury (Hg), cadmium (Cd) or lead (Pn) set out in Battery Directive (2006/66/EC).
The solid bar indicates that the product was placed on the market after 13th August, 2005.
Help protect the environment by disposing of your product or batteries responsibly.

General product care
To keep this product working well and looking good, follow these guidelines:
· Avoid placing it near heating appliances and devices that generate electrical noise (for example, motors or fluorescent lamps).
· DO NOT expose it to direct sunlight or moisture. · Avoid dropping the product or treating it roughly. · Clean with a soft damp cloth. · DO NOT immerse the parent unit and the baby unit in water and do not clean them under running water. · DO NOT use cleaning spray or liquid cleaners. · Make sure the baby unit and parent unit are dry before you connect them to the mains again.

Declaration of Conformity
This product is intended for use within Europe and UK. This equipment complies with the essential requirements to EU’s Radio Equipment Directive (2014/53/EU) and the UK’s Radio Regulations 2017 on radio systems and telecommunication equipment. VTech Telecommunications Ltd. hereby declares that this Video Baby Monitor VM819 is in compliance with the essential requirements and other relevant provisions of EU’s Radio Equipment Directive (2014/53/EU) and UK’s Radio Equipment Regulations 2017. The Declaration of Conformity for the VM819 is available from http://www.vtech.com/rtte-directive.
Manufacturer: VTech Telecommunications Ltd. 23/F., Tai Ping Industrial Centre, Block 1, 57 Ting Kok Road, Tai Po, Hong Kong. Importer: VTech Electronics Europe Plc. Napier Court, Abingdon Science Park, Abingdon, Oxon, OX14 3YT.
Credits: The Background Noise sound file was created by Caroline Ford, and is used under the Creative Commons license. The Stream Noise sound file was created by Caroline Ford, and is used under the Creative Commons license. The Crickets At Night sound file was created by Mike Koenig, and is used under the Creative Commons license. The Heart Beat sound file was created by Zarabadeu, and is used under the Creative Commons license.

Storage
When you are not going to use the baby monitor for some time, store the parent unit, the baby unit and the adaptors in a cool and dry place.
Adult supervision
· This baby monitor should be for use by adults only. · Do not place the baby unit inside the cot or playpen. · To ensure your children’s safety, do not allow them to touch or play with the baby monitor and its
accessories. THIS IS NOT A TOY.

Mount the baby unit on dry wall (optional)

Items to purchase
You will need to purchase the following items separately to mount your baby unit:

2 screws

2 anchors

Note
· The types of screws and anchors you need depend on the composition of the wall.

Insert the screws into the holes and tighten the screws until only 6mm of the screws are exposed.

Note
· Check for reception strength and camera angle before drilling the holes.
Use a pencil to mark two holes in parallel. Make sure they are the same distance apart as the wall mount holes on the baby unit.

Align the wall mount holes on the baby unit with the screws on the wall. Slide the baby unit down until it locks into place.

Drill two holes in the wall ( 5.5mm drill bit ). If you drill the holes into a stud, go to step 3.
-OR-
If you drill the holes into an object other than a stud, insert the wall anchors into the holes. Tap gently on the ends with a hammer until the wall anchors are flush with the wall.

Adjust the camera angle.