suprema XS2-QAPB X-Station 2 Compact RFID and Code Terminal User Guide
- June 6, 2024
- suprema
Table of Contents
**XS2-QAPB X-Station 2 Compact RFID and Code Terminal
User Guide**
X-Station 2
Compact RFID & QR Code Terminal
suprema 201.00.X52 V1.00A
Suprema Inc.
17F Parkview Tower, 248, Jeongjail-to, Bundang-Gu, Seongnam-si, Gyeonggi-do,
13554, Rep. of KOREA
Tel: +82 31 783 4502 I
Fax: +82 31 783 4503 I
Inquiry: sales_sys@supremainc.com
For more information about Supremo’s global branch offices, visit the webpage
below by scanning the QR code. https://www.supremainc.com/en/about/contact-
us.asp
NOTICE To download BioStar 2 installer and the guides for all devices that
support BioStar 2, visit
https://www.supremainc.com/en/support/biostar-2-package.asp.
Component
Cables and connectors
Cable | PIN | White stripe |
---|
Color
RI-4S
(Ethernet
+ PoE)| 1| ENET TXP| White
3| ENET TXN| Orange
5| ENET RXP| Black
7| ENET RXN| Yellow
TTL Input| 9| TTL GND| Gray
11| TTL INFO| Purple
13| 7TL1N1| Brown
RS-485| 15| 485 GND| White (Black stripe)
17| 485 TRXN| Yellow (Black stripe)
19| 485 TRIP| Blue (White stripe)
Wiegand| 21| WG D1| White
22| WG DO| Green
20| WG GRAND| Black
Relay| 18| RLY NO| Gray (WNW stripe)
16| RLY NC| Orange (White stripe)
14| RLY COM| Green (White stripe)
Power| 12| PWR +VDC| Red
10| PWR GND| Black (White stripe)
11-45
(Ethernet
+ PoE)| 8| VB2| Brown
6| VB2| Blue
4| VB1| Green
2| VB1| Red
Power Connection Network Connection
Wiegand Connection
RS- 485 Connection
Setting up the Device
This guide provides a brief description of time and attendance, and QR code
features. For more information, visit the Suprema webpage by scanning the QR
code and refer to the user guide.
https://supremainc.com/en/main.asp?
Time and Attendance
- Press -> AUTHENTICATION.
- Select and set the desired item.
- T &A Mode: Set the method to use T&A mode.
- T &A Code: You can register for T&A events. Select T&A Code —+ to register a T&A event and set an icon, name of T&A event, and schedule.
- T &A Required: Set to require a user to select a T&A event when authenticating.
- T &A Fixed: Set to use only a T&A event selected by the administrator. This option can be used when Fixed is set for T &A Mode.
- Job Code: Select whether or not to use Job Code.
QR Code Authentication
Use QR code authentication in places that require fast and easy issuance and
retrievals, such as shared offices or public facilities.
NOTE
– You can issue QR codes to users on BioStar 2.
– Supported devices: XS2-QAPB, XS2-QDPB
FCC compliance information
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment under FCC rules.
This appliance and its antenna must not be co-located or operated in
conjunction with any other antenna or transmitter. A minimum separation
distance of 20 cm must be maintained between the antenna and the person for
this appliance to satisfy the RF exposure requirements.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>