dji Quadrocopter, FPV Goggles V2 User Guide
- June 3, 2024
- DJi
Table of Contents
dji Quadrocopter, FPV Goggles V2
DJI Digital FPV System
DJ FPv
INSTALLATION
Press once to check the battery level.
Linking
Ensure that all devices are powered on.
- Press the link button on the air unit. The linking status indicator will turn solid red.
- Press the link button on the goggles. The goggles will beep continually.
- The linking status indicator of the air unit turns solid green. The goggles will stop beeping when they are successfully linked and the video display is normal.
If you need to use the Goggles and remote controller together, the air unit must be linked to the goggles before the remote controller.
When powered on, connect the goggles to a computer and run OJI ASSISTANT™ 2 for activation. When powered on, connect the goggles to a computer and run OJI ASSISTANT™ 2 for activation.
5D Button Toggle to scroll through the menu. Press to confirm.
Record Button Press to start or stop video recording.
Back Button
Press to return to the previous menu or exit the current mode.
Channel Adjustment Buttons
Press to switch channels.
Channel Display
Displays the current channel.
Disclaimer and Warning
Please read this entire document and all safe and lawful practices OJI™ provided carefully before use. Failure to read and follow instructions and warnings may result in serious injury to yourself or others, damage to your OJI product, or damage to other objects in the vicinity. By using this product, you hereby signify that you have read this disclaimer and warning carefully and that you understand and agree to abide by the terms and conditions herein. You agree that you are solely responsible for your own conduct while using this product, and for any consequences thereof. OJI accepts no liability for damage, injury or any legal responsibility incurred directly or indirectly from the use of this product. OJI is a trademark of SZ OJI TECHNOLOGY CO., LTD. (abbreviated as “OJI” ) and its affiliated companies. Names of products, brands, etc., appearing in this document are trademarks or registered trademarks of their respective owner companies. This product and document are copyrighted by OJI with all rights reserved. No part of this product or document shall be reproduced in any form without the prior written consent or authorization of OJI. This document and all other collateral documents are subject to change at the sole discretion of OJI. For up-to-date product information, visit http://www.dji.com and click on the product page for this product.
This disclaimer is available in various languages. In the event of divergence among different versions, the English version shall prevail.
Usage
Visit http://www.dji.com/fpv (User Manual) to learn more about how to use
this product with OJI FPV Air Unit.
Visit http://www.dji.com/dji-fpv (User Manual) to learn more about how to
use this product with OJI FPV Orone.
Specifications
Please refer to http://www.dji.com/service for after-sales service for your product where applicable. OJI shall mean SZ DJI TECHNOLOGY CO., LTD. and/or its affiliated companies where applicable.
Compliance Information
FCC Compliance Notice
This device complies “with ‘111 Part 15 of Iha FCC Rules. Operation is subject
to Iha
following two conditions:
- This device may not cause harmfu1 interference, and
- This device must accept any interference received, including interference that may cause an i.ndesired operation.
After changes or modifications not expressly approved by the party responsible for C001)lance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there,s no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turni1g the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Recent or relocate Iha receiving antenna.
- Increase the separation between the equipment and the receiver.
- connect the equipment to an outlet on a circuit different from that to which the recovery is connected.
- Consult the dealer or an experienCed redicv’TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The end user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA. These requirements set a SAR limit of 1.6 Wkg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.
ISED Compliance Notice
This device contains license-exempt transmitters (s/receivers) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with RSS-102 radiation exposure limits set forth for an uncontrolled environment. 1his equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. The end user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly wore on the body.
Compliance Statement: SZ DUI TECHNOLOGY CO.. LTD. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. A copy of the EU Declaration of Conformity is available online at www.dji.com euro- compliance EU contact address: DJI GmbH, Industriestrasse 12, 97618, Niederiauer Germany
Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of FRadio Equipment Regulations 2017. A copy of the GB Declaration of Conformity is available online at www.dji.com euro-compliance.
OJI is a trademark of OJI.
Copyright© 2021 OJI All Rights Reserved.
References
- CONSO s.r.l.
- DJI - Official Website
- DJI - Official Website
- DJI FPV - Redefine Flying - DJI
- DJI Digital FPV System - DJI
- Support - DJI
- Support - DJI