faytech 116N4200APLBMX 11.6 Inch APL Surface Mount Phase 3 User Manual

faytech 116N4200APLBMX 11.6 Inch APL Surface Mount Phase 3 User

Mechanical specifications

Technical Speciation

http://home.eeti.com.tw/LinuxDriverDownload.html

Mainboard: FAY-APL

| CPU| Apollo Lake N4200, (4C @ 2.50GHz CPU (Burst Mode), 750MHz GFX (Turbo), ~6W TDP)
Memory| 1 x SO-DIMM, max. 4GB, DDR3L 1333/1600/1867 non- ECC

Single channel memory

Graphics| Intel® HD Graphics
I/O Chipset| NUVOTON NCT6116D
LAN| 1 x LAN1 connector (POE LAN RJ45 connector, POE power connect to 2×2 2.54mm pin header)
 | Audio| 1 x Realtek Realtek/ALC3251
---|---|---
TPM| NPCT75XXX
WatchDog Timer| 1~255 step by software program
Wake On LAN / PXE| Yes (WOL / PXE)
Power State| S3, S4, S5
Graphics chipset| Intel® HD Graphics
Graphics Multi display| eDP or LVDS
eDP| Up to 1920 x 1080@60 Hz, (colay LVDS, BOM OPTION)
LVDS| Up to 1920 x 1200 @ 60Hz ,Resolution read from EEPROM, LCD Default 640*480
LVDS

Inverter Control

| Voltage / PWM, 1 x DC 5V/12V for LCD backlight inverter board
Battery| Lithium battery
Power Requiremen t| 1 x onboard 2 pin Power input connector (12 VDC ±10%)
System| RAM| 4GB DDR3L
SSD| mSATAIII M.2 2242 64GB
OS| Customized Windows 10 Pre-Installed
Camera| Brand/Mode l #| Logitech C930c
Pixel| 1080P
Focusing| Auto
LEN| FOV ：D= 90°
Interface| USB2.0, support USB3.0
Angle| Motor for angle adjustment available
Relay| Yoctopuce| Supplied by the customer
---|---|---
channel| 4x Channel
RFID| Operating frequency| 125kHz, 13.56MHz
Dimension| 50x35mm, with the latest firmware approved by BMX
Interface| USB HID, WG
Support Cards| EM4100、S50、NFC  P2P、HID26/34/35/36/37
Support system| Windows, Linux, moc, ios, Android
Read distance| 5cm
Output format| 8H10D， P2P 16D
4G (Optional)

（this product don’t has 4G module）

| Brand/Mode l| Sierra MC7455
 |  |
 |
Speaker|  | 2x 8O3W
Microphone|  | HD-6050P
Movement Sensor| Sensing Distance| 80CM
Braille|  | Yes
Front Panel Lightening| 8 Colors available| Red, Orange, Yellow, Green, Cyan, Blue, Purple, White
Ambient Light sensor| 3 Status available| Standard Lowest

Brightest

Ibeacon| UUID| Self-setting allowed
Transmissio n Power| Self-setting allowed
 | Input Voltage| 5V
---|---|---
frequency| 2.4G
External Interface|  | 2x USB 3.0
 | 1x COM port
 | 1xRJ45 (POE)
 | 1x SIM Slot
 | 1x24V DC-IN:

Pin 1/2: D+, Pin3/4: D-

| 1x 3pin Weigand Out
 | 4x Relay Channel
 | 1x Power Button
Environment| IP rating| IP65
IP Sealing Sponge Specificatio n| Model #：E-4088
 |  |
---|---|---
Operation Temperatur e| -20~60⁰
Accessories|  | 1x 24V/4A Power Supply, cable length=1.5meter
 | 1x AC Cable 1.5meter

Power adapter cable| Standard cable length=100mm, other length can be customized
 |  |
---|---|---
 | 1x Wallmount Plate
 | 1x Lock Key
Certification| FCC| To Be Applied

Explanation

Mainboard External I/O

Device External I/O

CPU Cooling

Function Explantion

The product is pre-installed windows system, power on after the normal use. If want to connect the device through Bluetooth, you need to turn on the Bluetooth switch in the system setting option, and search for the device to be paired and the connection. If want to connect to the wireless network through WiFi, the system has enabled the WiFi-function by default, select the corresponding wireless network to use. There is a card swiping area on the front of the product. You can use the card type sup-ported by this device about 5cm close to the swiping area.

FCC compliance statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Changelog

• 31.03.2022 Nathan Lu created
• 12.07.2022 Nathan Lu updates
• Adding in RFID dimension (50×35, the smaller version we used on keypad and 7inch ABS), and latest firmware approved by BMX
• RFID printing icon update
• Cooling profile on the back
• Adding in explanation on CPU cooling

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>